(8.) You can input http://192.168.9.9 in IE browser to enter the GUI page of upper level device and make sure the connection. ETOP 101 User’s Manual V1.
5.2.6 WPS Wi-Fi Protected Setup, it can simplify the procedures of wireless encryption between Server Router and wireless network card. If the wireless network card also supports WPS function, users can activate WPS auto-encryption to speed up the procedures. WPS supports 2 models: PIN (Personal Information Number) and PBC (Push Button Configuration). These models are approved by the Wi-Fi Alliance.
* Start PBC: (1.) Please click Start PBC to connect to the wireless network card. (2.) Open the configuration page of the wireless card which supports WPS. Click the WiFi Protect Setup, and then click PBC to make a WPS connection with AP from the WPS AP list (PBC-Scanning AP). ETOP 103 User’s Manual V1.
(3.) When you see Network Address, it means the WPS connection between wireless card and ETOP Server Router is established. 104 User’s Manual V1.
* Start PIN: (1.) Please open the configuration page of the wireless card, and write it down. ETOP 105 User’s Manual V1.
(2.) Open the Wi-Fi Protected Setup configuration page of Server Router, input the PIN number from the wireless card then click Start PIN. ETOP 106 User’s Manual V1.
(3.) Open the configuration page of the wireless card which supports WPS. Click the WPS, and then click PIN to make a WPS connection with AP from the WPS AP list (PIN-Begin associating to WPS AP). (4.) When you see Network Address, it means the WPS connection between wireless card and Server Router is established. ETOP 107 User’s Manual V1.
5.3 NAT 5.3.1 Visual Server Port forwarding service is to transfer packets from specific ports to corresponding IP address on local area network. ETOP 108 User’s Manual V1.
1. Enable Port Forwarding Please select to enable Port Forwarding service or not. 2. IP Address Please specify the IP address which receives the incoming packets. 3. Protocol Please select the protocol type. 4. Port Range Please enter the port number, for example 80-80 or 20-22。 5. Comment You can add comments for this port forwarding rule. 6. Apply Changes & Reset Click on Apply Changes to save the setting data. Or you may click on Reset to clear all the input data. 7.
5.3.2 Visual DMZ It will expose the computer which users enable the DMZ settings. All packets from the Internet will be forwarding to this computer. It is useful for specific applications, but please be careful to establish it. DMZ (Demilitarized Zone) Host is a zone that is not limited by the firewall service. DMZ allows you to redirect the packets from specific IP address to WAN IP address.
It will enable the DMZ service if you select it. 2. DMZ Host IP Address Please enter the specific IP address for DMZ host. 3. Apply Changes & Reset Click on Apply Changes to save the setting data. Or you may click on Reset to clear all the input data. 5.4 Firewall The Firewall service includes Port Filtering, IP Filtering, MAC Filtering, and URL Filtering. 5.4.
1. Enable Port Filtering Please select Enable Port Filtering to filter ports. 2. Port Range Please enter the port number that needs to be filtered. 3. Protocol Please select the protocol type of the port. 4. Comment You can add comments for this regulation. 5. Apply Changes & Reset Click on Apply Changes to save the setting data. Or you may click on Reset to clear all the input data. 6. Current Filter Table It will display all ports that are filtering now. 7.
*All clients inside the local area network can’t open the 80 port through this router. ETOP 113 User’s Manual V1.
5.4.2 IP Filtering This function can limit a specific ip address to access the Internet. The computer, whose ip address is listed on filter table, will be denied the access request by router. This protocol is made base on Internet Protocol and Transmission Control Protocol. 1. Enable IP Filtering Please select Enable IP Filtering to filter IP addresses. 2. Local IP Address Please enter the IP address that needs to be filtered. 3. Protocol Please select the protocol type of the IP address. 4.
This function can limit a specific MAC address to access the Internet. The network card, whose MAC address is listed on filter table, will be denied the access request by router. 1. Enable MAC Filtering Please select Enable MAC Filtering to filter MAC addresses. 2. MAC Address Please enter the MAC address that needs to be filtered. 3. Comment You can add comments for this regulation. 4. Apply Changes & Reset Click on Apply Changes to save the setting data.
1. Enable URL Filtering Please select Enable URL Filtering to filter web pages. 2. URL Address Please enter the URL of the web page. For example: www.google.com. 3. Apply Changes & Reset Click on Apply Changes to save the setting data. Or you may click on Reset to clear all the input data. 4. Current Filter table It will display all web pages that are filtering now. 5. Delete Selected & Delete All Click Delete Selected will delete the selected item. Click Delete All will delete all items in this table. 6.
Support NetBIOS Protocol, the consumer sharing file or printer which provides as the “My Network Places”. Please make sure storage devices and printers are connecting to USB ports on the router and already mounting. 1. Enable Samba Server Enable or disable this function. 2. Workgroup Name Input the workgroup name, default is “WORKGROUP”. 3. Server Name Input the server name, default is “ Server Router”. 4. Server Description You can input description of the server. 5.
Step 2: In the Address blank input the IP address: \\192.168.1.1. Step 3: Appear following menu, can open following to share internal data. ETOP 118 User’s Manual V1.
Note： 1. If connected USB flash or HDD, and then enable samba server function, it will appear a samba folder. 2. If connected USB printer, and then enable printer server function, it will appear a printer icon. 5.5.2 FTP Server FTP Server utility allows both local and remote users to upload or download files, pictures or MP3 music form the same storage device.
The default is 21. Define the FTP command transfer service port. If you want to change this port number, remember to change the service port setting of your FTP client, also. 5. Idle Connection Time-Out When a specific time value is added, FTP Server will be de-activated if it has no activity within the time limit. The default is 300 seconds; the minimum is 60 seconds. 6. Apply & Cancel Click on Apply button to continue. Click on Cancel button to clean the setting on this page. 7.
3. Image format The format is 320X240 pixels. 4. Preview Click on this button, you can preview the image from webcam. 5. Record Setting Please see the detail advance setting in “5.5.3.2 Webcam Advanced Configuration”. 6. Apply & Cancel Click on Apply button to continue. Click on Cancel button to clean the setting on this page. 5.5.3.2 Webcam Server Advanced Setting Click on “Record Setting” button, and the screen will appear as below. 1.
5. Remote FTP user Input the users name you like and it will be used to save the webcam image into the FTP server. 6. Remote FTP password Input the remote password. 7. Remote FTP Directory To provide option of which folder should be used for saving webcam image. 8. Back Click on Back button for returning to Webcam Basic Setting screen. 9. Apply & Cancel Click on Apply button to continue. Click on Cancel button to clean the setting on this page. 5.5.3.3 Application for Web Camera 5.5.3.3.
Monitor the image via webcam from WAN Input the WAN IP Address (as you see in above screen) into browser blanks, and you will see the personal account login screen appear then input your own user account and password. After login by personal, your will see the personal control panel screen as below, please click on “My Webcam”. Click on Personal Panel to enter. ETOP 123 User’s Manual V1.
There will be a pop-up screen showing the image from web camera as below example. ETOP 124 User’s Manual V1.
5.5.3.3.1.2 Web Camera Monitoring via mobile phone Also, you may view the monitor live action through mobile phones. Please key in the WAN IP address plus “/webcam.html” e.g. http://192.168.2.51/webcam.html into the mobile phone’s browser blank and you will see the webcam user login screen appeared. Input Username and Password of your own. You will see like as below monitor screen. ETOP 125 User’s Manual V1.
5.5.3.3.2 Web Camera Recording 5.5.3.3.2.1 Administrator Server Router also can record the pictures from Webcam; only Administrator can do the settings. Select Web Camera Server from main Menu and Enable this function, click on Record setting button for further setting. To setup the Webcam Advanced Configuration for each blank and the image from webcam will be recorded into your USB HDD or Remote FTP.
select Folder Management and click on Disk Explorer to view entire folder inside the disk including webcam record files. After click on Disk Explorer, you will see the folder screen appear including all the folders. All the image files will be saved in the folder “webcam_recorded_files”. Please open the file for checking. ETOP 127 User’s Manual V1.
5.5.3.3.2.2 Personal Application All the users under administrator’s setting can view entire webcam recording images from My Document. Please login by your own personal account. For viewing your own folder, please click on “My Document”. After click on “My Document”, you will see below folder screen appeared. You can save files here. Note：If you can’t open the folder inside the FTP server, please check with administrator to setup your FTP & Webcam’s privileges. 5.5.
1. Enable Printer Server Check Enable for applying printer server. 2. Enable Printer Access From WAN Allow printer can access from WAN side by checking on Enable for this item. 3. Printer Model The printer model will be shown when plug the USB printer. 4. Printer Name Input the name of printer you like. 5. Printer Description Input the description of printer as your demand. 6. Apply & Cancel Click on Apply button to continue. Click on Cancel button to clean the setting on this page.
Please go to Start > Printers and Faxes to add a printer. Step 2: Click “Add a printer”. Step 3: Click “Next”. ETOP 130 User’s Manual V1.
Step 4: Click the “Local printer attached to this computer”, and then click “Next”. Step 5: Click the “Create a new port” and select the “Standard TCP/IP Port”, and ETOP 131 User’s Manual V1.
then click “Next”. Step 6: Click “Next”. ETOP 132 User’s Manual V1.
Step 7: Input the IP address of Server Router: 192.168.1.1 (Router Mode), and then click “Next”. Step 8: Select the “Custom” and click the “Settings”, and then click “Next”. ETOP 133 User’s Manual V1.
Step 9: Select “LPR” and give it the same “Queue Name” as USB Printer Name as shown, and mark “LPR Byte Counting Enabled”. Finally, click on “OK” button. ETOP 134 User’s Manual V1.
Must as same as printer name, please refer to “3.2.10 Printer Server Setup” Step 10: Click the “Finish”. ETOP 135 User’s Manual V1.
Step 11: Select the “Manufacturer” and “Printers”. If your printer doesn’t listed in the table, please install its driver CD and then click on “Have Disk…” button for installation. Or click on “Next” button to finish the setting. ETOP 136 User’s Manual V1.
Step 12: Click on Finish button and all steps of setting printer server are completely. 5.6 System Management It has 6 sections: Change Password, Firmware Upgrade, Profiles Save, Time Zone Setting, UPnP Setting, and Language Setting. It is easy and helpful for users making more detailed settings. ETOP 137 User’s Manual V1.
ETOP 138 User’s Manual V1.
5.6.1 Change Password Users can set or change their password in this section. Please enter the password and confirm it. Click on Apply Changes to save the setting data. Or you may click on Reset to clear all the input data. 5.6.2 Firmware Upgrade This function can upgrade the firmware of the router. There is certain risk while doing firmware upgrading. Firmware upgrade is not recommended unless the significant faulty is found and published on official website.
Please download the firmware to the local computer first, and then browse it to upload. Caution: To prevent that firmware upgrading is interrupted by other wireless signals and causes failure. We recommend users to use wired connection during upgrading. Caution: The firmware upgrade will not remove your previous settings. *Reset button: On the back of this router, there is a reset button. If you can not login the administrator page by forgetting your password; or the router has problem you can’t solve.
default. Save it to a computer. Reset to default. Upload the file from PC to router. *Please see the following instructions. a. Please click Save…, a prompt window will ask user to save config.dat file. (Figure 1), please select the location (Figure 2), for example: the desktop (Figure 3). ETOP 141 User’s Manual V1.
(Figure 1) (Figure 2) (Figure 3) ETOP 142 User’s Manual V1.
b. Please click Browser… (Figure 1) and select the config.dat file. (Figure 2), and then click Upload to retrieve (Figure 3). (Figure 1) (Figure 2) ETOP 143 User’s Manual V1.
(Figure 3) c. When you see the screen displaying like the following figure, it means update is completed. Please click OK to turn back to the configuration page. d. if you want to reset the system back to factory default settings, please click Reset button. ETOP 144 User’s Manual V1.
e. When you see the screen displaying like the following figure, it means reset is completed. Please click OK to turn back to the configuration page. 5.6.4 Time Zone Setting This function allows users to select their time zone and NTP server. Users can adjust the time manually or through the NTP server. ETOP 145 User’s Manual V1.
Please select the time zone. 1. Current Time Users can input the time manually. 2. Time Zone Select Please select the time zone. 3. Enable NTP client update Please select to enable NTP client update or not. 4. Automatically Adjust Daylight Saving Please select to enable Automatically Adjust Daylight Saving or not. 5. NTP server Please select the NTP server from the pull-down list, or you can enter the NTP server IP address manually. 6.
Network Places. Users will see an Internet Gateway Device icon. By click the icon, users can enter the GUI of Server Router. If you do not wish to use UPnP, you can disable it. 5.5.6 Language Setting Server Router provides users with 12 languages to choose. Users can change the language of the interface configuration. Please click Apply Changes after selecting a language. ETOP 147 User’s Manual V1.
Using Korean as an example, the screen will display on the chosen language after the countdown is finished. Caution: After countdown, you can press Ctrl+F5 forcing the page to refresh. This can avoid any translation uncompleted situation. 5.5.7 ETOP User Account Management 148 User’s Manual V1.
Personal users can use each individual application such as My Status, My Webcam and My Document. This section is to set the user’s right. Also, all the users right will be showed in User Account List and can do the edit or delete by clicking the meaning text. 1. User Name Create the user name in this blank. 2. Password Setup the user’s password. 3. User Right Enable the use to Webcam, FTP server. 4. Apply & Cancel Click on Apply button to add the settings into the list table.
1. Select the USB Disk and click on Mount button for refresh all disks before you do disk partition, and the Unplug button will appear. 2. To partition/format the disk, please select the disk and click on Format button. 3. If you want to view the data inside the disk, please click on “Disk Explorer” to view all the disks folders inside the device. Note：You have to click on “Unplug” button before remove the USB devices. ETOP 150 User’s Manual V1.
5.6 Log & Status The category provides Network Config and Event Log status for users to know the operation status. 5.6.1 Network Config Users can check the Internet status under this category, including Firmware version, Wireless setting, Connecting Time, WAN, TCP/IP …information. ETOP 151 User’s Manual V1.
5.6.2 Event Log You may enable the event log feature here. Please select to enable log function. 1. Enable Log You may choose to enable Event Log or not. ETOP 152 User’s Manual V1.
2. system all、wireless & DoS Please select the event you want to record. 3. Enable Remote Log You may choose to enable the remote event log or not. 4. Log Server IP Address Please input the log server IP Address. 5. Apply Changes & Refresh & Clear Click on Apply Changes to save the setting data. Click on Refresh to renew the system time, or on Clear to clear all the record. *The following figure is an example when users click Apply Changes to record the event log. 5.
Chapter 6 Advanced Configuration for AP Mode 6.1 IP Config In this category, you can setup the IP rules under AP Mode. 6.1.1 LAN Setup Please click on LAN of IP Config and follow the below setting. 6.1.2 LAN Interface Setup This page is used to configure for local area network which connects to the LAN port of your Access Point. Here users may change the setting for IP address, Subnet Mask, DHCP, etc. ETOP 154 User’s Manual V1.
1. IP Address The default IP address is 192.168.1.254 (recommend). 2. Subnet Mask Please enter the Subnet Mask address; it should be 255.255.255.0 for the most time. 3. Default Gateway Please enter the Default Gateway address. If you don’t know the address, please contact your ISP. 4. DHCP Users can choose to enable DHCP service or not. The DHCP server will give an unused IP address to a computer which is requesting for one.
6.2 Wireless Setup The category includes Basic Settings, Advanced Settings, Security, Access Control, WDS settings, and WPS. Please read below for the setting instruction. 6.2.1 Wireless Basic Settings The basic settings related to the wireless are specified as following. ETOP 156 User’s Manual V1.
1. Disable Wireless LAN Interface Turn off the wireless function. 2. Band Please select the frequency. It has 6 options: 2.4 GHz (B/G/N/B+G/G+N/B+G+N). 3. Mode Please select the mode. It has 3 modes to select: (AP, WDS, AP+WDS). Multiple APs can provide users another 4 different SSID for connection. Users can add or limit the properties for each connection. ETOP 157 User’s Manual V1.
(1.) Enable: please choose to enable it or not. (2.) Band: please select the frequency. (3.) SSID: please enter the SSID. (4.) Data Rate: please select the data transmission rate. (5.) Access: enable this function can let clients use 2 access types: a. LAN+WAN: the client can access to the Internet and connect to Server Router’s GUI to setup. b. WAN: the client can only access to the Internet. (6.) Active Client List: display the properties of the client which is connecting successfully. (7.
4. Network Type Please select the network type, it has 2 options: Infrastructure or Ad hoc. If the wireless mode is set to AP mode, this section is disabled. 5. SSID Service Set identifier, the default SSID is Server_Router, users can define to any. 6. Channel Width Please select the channel width, it has 2 options: 20MHZ, and 40MHZ. 7. Control Sideband Enable this function will control your router use lower or upper channel. 8.
12. Enable Mac Clone (Single Ethernet Client) Clone the MAC address for ISP to identify. 13. Enable Universal Repeater Mode (Acting as AP and Client simultaneously) Allow to equip with the wireless way conjunction upper level, provide the bottom layer user link in wireless and wired way in the meantime. (The IP that bottom layer obtains is from upper level.
Server_Router_0d21ff If the bottom layer device is trying to make a connection, users must input the SSID of this router as a relay station. The IP that the bottom layer device gets is from the upper level device. 14. SSID of Extended Interface While linking the upper level device in wireless way, you can set SSID to give the bottom layer user search. 15. Apply Changes & Reset Click on Apply Changes to save the setting data. Or you may click on Reset to clear all the input data. 6.2.
1. Fragment Threshold To identify the maxima length of packet, the over length packet will be fragmentized. The allowed range is 256-2346, and default length is 2346 Bytes. 2. RTS Threshold This value should remain at its default setting of 2347. The range is 0~2347. Should you encounter inconsistent data flow, only minor modifications are recommended. If a network packet is smaller than the present RTS threshold size, the RTS/CTS mechanism will not be enabled.
form transmission to PHY (Physical layer). There are two options, Short Preamble and Long Preamble. The Short Preamble option improves throughput performance. Select the suit Preamble as Short or Long Preamble. 5. IAPP Inter Access Point Protocol. Allow seamless roaming between Access Points in your wireless network. 6. Protection Please select to enable wireless protection or not. 7. Aggregation Enable this function will combine several packets to one and transmit it.
6.2.3 Wireless Security Setup 4 encryption types could be selected here, please follow below instruction for the setting. 1. Encryption – WEP 1.1 Set WEP Key This section provides 64bit and 128bit WEP encryptions for wireless network. Users can also choose ASCII and Hex shared Key format to protect data. ETOP 164 User’s Manual V1.
1.2 802.1x Authentication It is a safety system by using authentication to protect your wireless network. Please choose between WEP 64bits and WEP 128bits. 4. Encryption – WPA（WPA, WPA2, and WPA2 Mixed） WPA Authentication Mode 2.1 Enterprise（RADIUS） Please input the Port, IP Address, and Password of Authentication RADIUS Server. 2.2 Personal（Pre-Shared Key） Pre-Shared Key type is ASCII Code; the length is between 8 to 63 characters. If the key type is Hex, the key length is 64 characters.
2. Apply Changes & Reset Click on Apply Changes to save the setting data. Or you may click on Reset to clear all the input data. ETOP 166 User’s Manual V1.
6.2.4 Wireless Access Control The function of access control is to allow or deny users to access Server Router by according MAC address, it is optional. If you select Allowed Listed, then only those clients whose MAC address is listed on access control can connect to your base station. If you select Deny Listed, those clients whose MAC address is listed on access control can’t connect to your base station. Users may enable or disable this function. Take the wireless card as the example. (1.
(2.) You will find out that the MAC address appears on Current Access Control List, it means the initiation is completed. (3.) Please open wireless card UI and try to connect to this router. You will find out that the connection request will be denied. ETOP 168 User’s Manual V1.
6.2.5 WDS Settings Wireless basic settings must enable WDS first. This function can communicate with other APs by adding MAC address into the same channel. ETOP 169 User’s Manual V1.
* The following figure is the explanation. Wireless Connection AP Router WDS AP Router WDS Internet Wired Connection * Please follow the instructions to setup the connection. (1.) Please check the MAC address and Channel number of the upper level device. ETOP 170 User’s Manual V1.
Server_Router (2.) Enter the Wireless Basic Settings page, select AP+WDS mode, and then select the Channel Number. Click Apply Changes to save the setting data. (3.) Enter the WDS Settings page, select Enable WDS, and then input the MAC address of the upper level device. Click Apply Changes to save the setting data. ETOP 171 User’s Manual V1.
(4.) When the time counts down to 0, you will see the MAC address of the upper level device displaying on Current WDS AP List. ETOP 172 User’s Manual V1.
(5.) Head back to LAN Interface, disable DHCP option, and then click Apply Changes to save the setting data. (6.) The MAC address of the upper level device is going to setup like the MAC address of the router. Enter the upper level device’s WDS settings page, and input router’s MAC address. Click Apply Changes to save the setting data. Please input the MAC address. (7.) After initiating the upper level device, please check Local Area Connections. ETOP 173 User’s Manual V1.
Click Supports to check out the IP address which is assigned by upper level device. (8.) You can input http://192.168.9.9 in IE browser to enter the GUI page of the upper level device and make sure the connection. ETOP 174 User’s Manual V1.
6.2.6 WPS Wi-Fi Protected Setup, it can simplify the procedures of wireless encryption between Server Router and wireless network card. If the wireless network card also supports WPS function, users can activate WPS auto-encryption to speed up the procedures. WPS supports 2 models: PIN (Personal Information Number) and PBC (Push Button Configuration). These models are approved by the Wi-Fi Alliance.
* Start PBC: (1.) Please click Start PBC to connect to the wireless network card. (2.) Open the configuration page of the wireless card which supports WPS. Click the WiFi Protect Setup, and then click PBC to make a WPS connection with AP from the WPS AP list (PBC-Scanning AP). ETOP 176 User’s Manual V1.
(3.) When you see Network Address, it means the WPS connection between wireless card and Server Router is established. ETOP 177 User’s Manual V1.
* Start PIN: (1.) Please open the configuration page of the wireless card, and write it down. ETOP 178 User’s Manual V1.
(2.) Open the Wi-Fi Protected Setup configuration page of Server Router, input the PIN number from the wireless card then click Start PIN. ETOP 179 User’s Manual V1.
(3.) Open the configuration page of the wireless card which supports WPS. Click the WPS, and then click PIN to make a WPS connection with AP from the WPS AP list (PIN-Begin associating to WPS AP). (4.) When you see Network Address, it means the WPS connection between wireless card and Server Router is established. ETOP 180 User’s Manual V1.
6.3 Server Server Router provides Samba Server, FTP Server, Web Camera Server, and Printer Server Application. 6.3.1 Samba Server Support NetBIOS Protocol, the consumer sharing file or printer which provides as the “My Network Places”. Please make sure storage devices and printers are connecting to USB ports on the router and already mounting. ETOP 181 User’s Manual V1.
1. Enable Samba Server Enable or disable this function. 2. Workgroup Name Input the workgroup name, default is “WORKGROUP”. 3. Server Name Input the server name, default is “ Server Router”. 4. Server Description You can input description of the server. 5. Apply & Cancel Click on Apply button to finish setting. Click on Cancel button to clean the setting on this page. 6.3.1.1 How to Enter The Sharing Folder Please follow below steps. Step 1: Please click the “start”, and select “My Computer”.
Step 2: In the Address blank input the IP address: \\192.168.1.254. Step 3: Appear following menu, can open following to share internal data. ETOP 183 User’s Manual V1.
Note： 3. If connected USB flash or HDD, and then enable samba server function, it will appear a samba folder. 4. If connected USB printer, and then enable printer server function, it will appear a printer icon. 6.3.2 FTP Server FTP Server utility allows both local and remote users to upload or download files, pictures or MP3 music form the same storage device.
The default is 21. Define the FTP command transfer service port. If you want to change this port number, remember to change the service port setting of your FTP client, also. 4. Idle Connection Time-Out When a specific time value is added, FTP Server will be de-activated if it has no activity within the time limit. The default is 300 seconds; the minimum is 60 seconds. 5. Apply & Cancel Click on Apply button to continue. Click on Cancel button to clean the setting on this page. 6.
3. Preview Click on this button, you can preview the image from webcam. 4. Record Setting Please see the detail advance setting in “6.3.3.2 Webcam Advanced Configuration”. 5. Apply & Cancel Click on Apply button to continue. Click on Cancel button to clean the setting on this page. 6.3.3.2 Webcam Server Advanced Setting Click on “Record Setting” button, and the screen will appear as below. 1. Save image interval For saving image, you can set the save interval time, the default value is 5 seconds. 2.
into the FTP server. 6. Remote FTP password Input the remote password. 7. Remote FTP Directory To provide option of which folder should be used for saving webcam image. 8. Back Click on Back button for returning to Webcam Basic Setting screen. 9. Apply & Cancel Click on Apply button to continue. Click on Cancel button to clean the setting on this page. 6.3.3.3 Application for Webcam 6.3.3.3.1 Web Camera Monitoring Application Monitor your home with a Webcam via Server Router.
Click on Personal Panel to enter. There will be a pop-up screen showing the image from web camera as below example. ETOP 188 User’s Manual V1.
6.3.3.3.1.2 Web Camera Monitoring via Mobile Phone Also, you may view the monitor live action through mobile phones. Please key in the WAN IP address plus “/webcam.html” e.g. http://192.168.1.254/webcam.html into the mobile phone’s browser blank and you will see the webcam user login screen appeared. Input Username and Password of your own. You will see like as below monitor screen. ETOP 189 User’s Manual V1.
6.3.3.3.2 Web Camera Recording 6.3.3.3.2.1 Administrator Server Router also can record the pictures from Webcam; only Administrator can do the settings. Select Web Camera Server from main Menu and Enable this function, click on Record setting button for further setting. To setup the Webcam Advanced Configuration for each blank and the image from webcam will be recorded into your USB HDD or Remote FTP.
select Folder Management and click on Disk Explorer to view entire folder inside the disk including webcam record files. After click on Disk Explorer, you will see the folder screen appear including all the folders. All the image files will be saved in the folder “webcam_recorded_files”. Please open the file for checking. ETOP 191 User’s Manual V1.
6.3.3.3.2.2 Personal Application All the users under administrator’s setting can view entire webcam recording images from My Document. Please login by your own personal account. For viewing your own folder, please click on “My Document”. After click on “My Document”, you will see below folder screen appeared. You can save files here. Note：If you can’t open the folder inside the FTP server, please check with administrator to setup your FTP & Webcam’s privileges. ETOP 192 User’s Manual V1.
6.3.4 Printer Server The two USB ports on Server Router are for connection with printers to be shared on the local area network. Follow the below steps to setup your PC to connect to a Printer server. 1. Enable Printer Server Check Enable for applying printer server. 2. Printer Model The printer model will be shown when plug the USB printer. 3. Printer Name Input the name of printer you like. 4. Printer Description Input the description of printer as your demand. 5.
Step 1: Please go to Start > Printers and Faxes to add a printer. Step 2: Click “Add a printer”. Step 3: Click “Next”. ETOP 194 User’s Manual V1.
Step 4: Click the “Local printer attached to this computer”, and then click “Next”. Step 5: ETOP 195 User’s Manual V1.
Click the “Create a new port” and select the “Standard TCP/IP Port”, and then click “Next”. Step 6: Click “Next”. ETOP 196 User’s Manual V1.
Step 7: Input the IP address of Server Router: 192.168.1.254, and then click “Next”. Step 8: Select the “Custom” and click the “Settings”, and then click “Next”. ETOP 197 User’s Manual V1.
Step 9: Select “LPR” and give it the same “Queue Name” as USB Printer Name as shown, and mark “LPR Byte Counting Enabled”. Finally, click on “OK” button. Must as same as printer name, please refer to “6.3.4 Printer Server Setup” Step 10: Click the “Finish”. ETOP 198 User’s Manual V1.
Step 11: Select the “Manufacturer” and “Printers”. If your printer doesn’t listed in the table, please install its driver CD and then click on “Have Disk…” button for installation. Or click on “Next” button to finish the setting. ETOP 199 User’s Manual V1.
Step 12: Click on Finish button and all steps of setting printer server are completely. 6.4 System Management It has 6 sections: Change Password, Firmware Upgrade, Profiles Save, Time Zone Setting, UPnP Setting, and Language Setting. It is easy and helpful for users making more detailed settings. ETOP 200 User’s Manual V1.
