6.4.1 Change Password Users can set or change their password in this section. Please input the new password and confirm it. Click on Apply Changes to save the setting data. Or you may click on Reset to clear all the input data. ETOP 201 User’s Manual V1.
6.4.2 Firmware Upgrade This function can upgrade the firmware of the router. There is certain risk while doing firmware upgrading. Firmware upgrade is not recommended unless the significant faulty is found and published on official website. If you feel the router has unusual behaviors and is not caused by the ISP and environment. You can check the website (http://www.etopnetwork.com.tw) to see if there is any later version of firmware.
6.4.3 Profiles Save Users can save or restore the setting profile, and reset the setting to factory default. Save to user pc. Reset to the factory default settings. Upload from user pc. * Please see the following instructions. a. Please click Save…, a prompt window will ask user to save config.dat file. (Figure 1), please select the location (Figure 2), for example: the desktop (Figure 3). ETOP 203 User’s Manual V1.
(Figure 1) ETOP 204 User’s Manual V1.
(Figure 2) (Figure 3) b. Please click Browser… (Figure 1) and select the config.dat file. (Figure 2), and then click Upload to retrieve (Figure 3). ETOP 205 User’s Manual V1.
(Figure 1) (Figure 2) ETOP 206 User’s Manual V1.
(Figure 3) c. When you see the screen displaying like the following figure, it means update is completed. Please click OK to turn back to the configuration page. d. if you want to reset the system back to factory default settings, please click Reset button. ETOP 207 User’s Manual V1.
e. When you see the screen displaying like the following figure, it means reset is completed. Please click OK to turn back to the configuration page. 6.4.4 Time Zone Setting This function allows users to select their time zone and NTP server. Users can adjust the time manually or through the NTP server. ETOP 208 User’s Manual V1.
Please select the time zone. 1. Current Time Users can input the time manually. 2. Time Zone Select Please select the time zone. 3. Enable NTP client update Please select to enable NTP client update or not. 4. Automatically Adjust Daylight Saving Please select to enable Automatically Adjust Daylight Saving or not. 5. NTP server Please select the NTP server from the pull-down list, or you can enter the NTP server IP address manually. 6.
can disable it. 6.4.6 Language Setting Server Router provides users with 12 languages to choose. Users can change the language of the interface configuration. Please click Apply Changes after selecting a language. ETOP 210 User’s Manual V1.
Using Korean as an example, the screen will display on the chosen language after the countdown is finished. Caution: After countdown, you can press Ctrl+F5 forcing the page to refresh. This can avoid any translation uncompleted situation. 6.4.7 User Account Management Personal users can use each individual application such as My Status, My Webcam and My Document. This section is to set the user’s right.
1. User Name Create the user name in this blank. 2. Password Setup the user’s password. 3. User Right Enable the use to Webcam, FTP server. 4. Apply & Cancel Click on Apply button to add the settings into the list table. Click on Cancel button to clean the setting on this page. 6.4.
1. Select the USB Disk and click on Mount button for refresh all disks before you do disk partition, and the Unplug button will appear. 2. To partition/format the disk, please select the disk and click on Format button. 3. If you want to view the data inside the disk, please click on “Disk Explorer” to view all the disks folders inside the device. Note：You have to click on “Unplug” button before remove the USB devices. 6.
6.5.1 Network Config Users can check the Internet status under this category, including Firmware version, Wireless setting, Connecting Time, WAN, TCP/IP …information. Server_Router_0d21ff 6.5.2 Event Log You may enable the event log feature here. ETOP 214 User’s Manual V1.
Please select to enable log function. 1. Enable Log You may choose to enable Event Log or not. 2. system all、wireless & DoS Please select the event you want to record. 3. Enable Remote Log You may choose to enable the remote event log or not. 4. Log Server IP Address Please input the log server IP Address. 5. Apply Changes & Refresh & Clear Click on Apply Changes to save the setting data. Click on Refresh to renew the system time, or on Clear to clear all the record.
6.5 Logout This function provides users to logout. Click on Apply Change to logout. ETOP 216 User’s Manual V1.
Chapter 7 Advanced Configuration for WiFi AP Mode 7.1 IP Config This section can let users add route rules of Server Router; it includes configuration of LAN. 7.1.1 IP Config - LAN 7.1.2 LAN Interface Setup This page is used to configure for local area network which connects to the LAN port of your Access Point. Here users may change the setting for IP address, Subnet Mask, DHCP, etc. ETOP 217 User’s Manual V1.
1. IP Address The default IP address is 192.168.1.254 (recommend). 2. Subnet Mask Please enter the Subnet Mask address; it should be 255.255.255.0 for the most time. 3. Default Gateway Please enter the Default Gateway address. If you don’t know the address, please contact your ISP. 4. DHCP Users can choose to enable DHCP service or not. The DHCP server will give an unused IP address to a computer which is requesting for one.
8. Apply Changes & Reset Click on Apply Changes to save the setting data. Or you may click on Reset to clear all the input data. 7.2 Wireless Setup The category includes Basic Settings, Advanced Settings, Site Survey, Security, Access Control, and WPS. Please read below for the setting instructions. 7.2.1 Wireless Basic Setting The basic settings related to the wireless are specified as following. ETOP 219 User’s Manual V1.
1. Disable Wireless LAN Interface Turn off the wireless function. 2. Band Please select the frequency. It has 6 options: 2.4 GHz (B/G/N/B+G/G+N/B+G+N). 3. Mode Please select the mode. It has 3 modes to select: (AP, WDS, AP+WDS) 4. Network Type Please select the network type, it has 2 options: Infrastructure or Ad hoc. If the wireless mode is set to AP mode, this section is disabled. ETOP 220 User’s Manual V1.
5. SSID Service Set identifier, the default SSID is Server_Router, users can define to any. 6. Channel Width Please select the channel width, it has 2 options: 20MHZ, and 40MHZ. 7. Control Sideband Enable this function will control your router use lower or upper channel. 8. Channel Number Please select the channel; it has Auto, 1, 2~11 options. 9. Broadcast SSID User may choose to enable Broadcast SSID or not. 10. Data Rate Please select the data transmission rate. 11.
---------------------------------------------------------------------------------Users can go to the network Config section and check the information of upper level in Wireless Repeater Interface Configuration. Server_Router_0d21ff Caution: when users enable the wireless encryption. The upper level and lower devices can connect to each other even if their encryption types are not the same. 14.
1. Fragment Threshold To identify the maxima length of packet, the over length packet will be fragmentized. The allowed range is 256-2346, and default length is 2346. 2. RTS Threshold This value should remain at its default setting of 2347. The range is 0~2347. Should you encounter inconsistent data flow, only minor modifications are recommended. If a network packet is smaller than the present RTS threshold size, the RTS/CTS mechanism will not be enabled.
header to create the PPDU. It has 2 options: Long Preamble and Short Preamble. 5. IAPP Inter-Access Point Protocol is a recommendation that describes an optional extension to IEEE 802.11 that provides wireless access-point communications among multivendor systems. 6. Protection Please select to enable wireless protection or not. 7. Aggregation Enable this function will combine several packets to one and transmit it. It can reduce the problem when mass packets are transmitting. 8.
7.2.4 Wireless Security Setup 4 encryption types could be selected here, please follow below instructions for the setting. 1. Encryption – WEP 1.1 Set WEP Key This section provides 64bit and 128bit WEP encryptions for wireless network. Users can also choose ASCII and Hex shared Key format to protect data. ETOP 225 User’s Manual V1.
1.1 802.1x Authentication It is a safety system by using authentication to protect your wireless network. Please choose between WEP 64bits and WEP 128bits. 2. Encryption – WPA（WPA、WPA2 & WPA2 Mixed） WPA Authentication Mode 2.1 Enterprise (RADIUS) Please input the Port, IP Address, and Password of Authentication RADIUS Server. ETOP 226 User’s Manual V1.
2.2 Personal（Pre-Shared Key） Pre-Shared Key type is ASCII Code; the length is between 8 to 63 characters. If the key type is Hex, the key length is 64 characters. ETOP 227 User’s Manual V1.
3. Apply Changes & Reset Click on Apply Changes to save the setting data. Or you may click on Reset to clear all the input data. ETOP 228 User’s Manual V1.
7.2.5 Access Control The function of access control is to allow or deny users to access Server Router by according MAC address, it is optional. If you select Allowed Listed, then only those clients whose MAC address is listed on access control can connect to your base station. If you select Deny Listed, those clients whose MAC address is listed on access control can’t connect to your base station.。 Users can enable and disable this function. *Take the wireless card as the example. (1.
(2.) You will find out that the MAC address appears on Current Access Control List, it means the initiation is completed. (3.) Please open wireless card UI and try to connect to this router. You will find out that the connection request will be denied. ETOP 230 User’s Manual V1.
7.2.6 WPS Wi-Fi Protected Setup, it can simplify the procedures of wireless encryption between Server Router and wireless network card. If the wireless network card also supports WPS function, users can activate WPS auto-encryption to speed up the procedures. WPS supports 2 models: PIN (Personal Information Number) and PBC (Push Button Configuration). These models are approved by the Wi-Fi Alliance.
When users select a specific model on wireless base station, the clients can connect to the base by selecting the same model. The connection procedures of PIN and PBC are almost the same. The small difference between those two is: Users input the PIN of wireless card in the base station first; it will limit the range of the clients. It is faster to establish a connection on PIN model.
(2.) Open the configuration page of the wireless card which supports WPS. Click the WiFi Protect Setup, and then click PBC to make a WPS connection with AP from the WPS AP list (PBC-Scanning AP). ETOP 233 User’s Manual V1.
(3.) When you see Network Address, it means the WPS connection between wireless card and Server Router is established. ETOP 234 User’s Manual V1.
* Start PIN: (1.) Please open the configuration page of the wireless card, and write it down. ETOP 235 User’s Manual V1.
(2.) Open the Wi-Fi Protected Setup configuration page of Server Router, input the PIN number from the wireless card then click Start PIN. ETOP 236 User’s Manual V1.
(3.) Open the configuration page of the wireless card which supports WPS. Click the WPS, and then click PIN to make a WPS connection with AP from the WPS AP list (PIN-Begin associating to WPS AP). (4.) When you see Network Address, it means the WPS connection between wireless card and Server Router is established. ETOP 237 User’s Manual V1.
ETOP 238 User’s Manual V1.
7.3 Server Server Router provides Samba Server, FTP Server, Web Camera Server, and Printer Server Application. 7.3.1 Samba Server Support NetBIOS Protocol, the consumer sharing file or printer which provides as the “My Network Places”. Please make sure storage devices and printers are connecting to USB ports on the router and already mounting. 6. Enable Samba Server Enable or disable this function. 7. Workgroup Name Input the workgroup name, default is “WORKGROUP”. ETOP 239 User’s Manual V1.
8. Server Name Input the server name, default is “ Server Router”. 9. Server Description You can input description of the server. 10. Apply & Cancel Click on Apply button to finish setting. Click on Cancel button to clean the setting on this page. 7.3.1.1 How to Enter Sharing Folder Please follow below steps. Step 1: Please click the “start”, and select “My Computer”. ETOP 240 User’s Manual V1.
Step 2: In the Address blank input the IP address: \\192.168.1.254. Step 3: Appear following menu, can open following to share internal data. Note： 5. If connected USB flash or HDD, and then enable samba server function, it will appear a samba folder. 6. If connected USB printer, and then enable printer server function, it will appear a printer icon. 7.3.2 FTP Server FTP Server utility allows both local and remote users to upload or download files, pictures or MP3 music form the same storage device.
1. Enable FTP Server Select to “Enable” or “Disable” FTP server. 2. Enable Anonymous to Login Allow anonymous to login after check on Enable. 3. FTP Server Port The default is 21. Define the FTP command transfer service port. If you want to change this port number, remember to change the service port setting of your FTP client, also. 4. Idle Connection Time-Out When a specific time value is added, FTP Server will be de-activated if it has no activity within the time limit.
1. Enable Webcam Server Select to “Enable” or “Disable” webcam server. 2. Image format The format is 320X240 pixels. 3. Preview Click on this button, you can preview the image from webcam. 4. Record Setting Please see the detail advance setting in “4.4.3.2 Webcam Advanced Configuration”. 5. Apply & Cancel Click on Apply button to continue. Click on Cancel button to clean the setting on this page. 7.3.3.2 Webcam Advanced Setting Click on “Record Setting” button, and the screen will appear as below.
1. Save image interval For saving image, you can set the save interval time, the default value is 5 seconds. 2. Save Location Set the save location for webcam image, you may save into USB HDD or Remote FTP; if select save to Remote FTP, please continue following remote FTP setting. 3. Remote FTP URL Input the FTP URL for saving webcam image. 4. Remote FTP port Input the FTP port number under URL to save image. 5.
7.3.3.3 Application for Webcam 7.3.3.3.1 Web Camera Monitoring Application Monitor your home with a Webcam via Server Router. Take pictures via Server Router, also can do the monitoring or recording all images into the USB HDD for reviewing. Often marketed as surveillance tools for home or office security, network Webcams are now being employed by early adopters for more personal matters, such as watching kids and monitoring pets. The Webcam can be remotely accessed and controlled via a browser.
There will be a pop-up screen showing the image from web camera as below example. ETOP 246 User’s Manual V1.
7.3.3.3.1.2 Web Camera Monitoring via Mobile Phone Also, you may view the monitor live action through mobile phones. Please key in the WAN IP address plus “/webcam.html” e.g. http://192.168.1.254/webcam.html into the mobile phone’s browser blank and you will see the webcam user login screen appeared. Input Username and Password of your own. You will see like as below monitor screen. 7.3.3.3.2 Web Camera Recording 247 User’s Manual V1.
7.3.3.3.2.1 Administrator Server Router also can record the pictures from Webcam; only Administrator can do the settings. Select Web Camera Server from main Menu and Enable this function, click on Record setting button for further setting. To setup the Webcam Advanced Configuration for each blank and the image from webcam will be recorded into your USB HDD or Remote FTP.
All the image files will be saved in the folder “webcam_recorded_files”. Please open the file for checking. 249 User’s Manual V1.
7.3.3.3.2.2 Personal Application All the users under administrator’s setting can view entire webcam recording images from My Document. Please login by your own personal account. For viewing your own folder, please click on “My Document”. After click on “My Document”, you will see below folder screen appeared. You can save files here. Note：If you can’t open the folder inside the FTP server, please check with administrator to setup your FTP & Webcam’s privileges. 7.3.
1. Enable Printer Server Check Enable for applying printer server. 2. Printer Model The printer model will be shown when plug the USB printer. 3. Printer Name Input the name of printer you like. 4. Printer Description Input the description of printer as your demand. 5. Apply & Cancel Click on Apply button to continue. Click on Cancel button to clean the setting on this page. Besides above setting finished, the printer setting on PC also needs to be set as follows. 7.3.4.
Step 2: Click “Add a printer”. Step 3: Click “Next”. 252 User’s Manual V1.
Step 4: Click the “Local printer attached to this computer”, and then click “Next”. Step 5: 253 User’s Manual V1.
Click the “Create a new port” and select the “Standard TCP/IP Port”, and then click “Next”. Step 6: Click “Next”. 254 User’s Manual V1.
Step 7: Input the IP address of Server Router: 192.168.1.254, and then click “Next”. Step 8: Select the “Custom” and click the “Settings”, and then click “Next”. 255 User’s Manual V1.
Step 9: Select “LPR” and give it the same “Queue Name” as USB Printer Name as shown, and mark “LPR Byte Counting Enabled”. Finally, click on “OK” button. Must as same as printer name, please refer to “7.3.4 Printer Server Setup” Step 10: Click the “Finish”. 256 User’s Manual V1.
Step 11: Select the “Manufacturer” and “Printers”. If your printer doesn’t listed in the table, please install its driver CD and then click on “Have Disk…” button for installation. Or click on “Next” button to finish the setting. 257 User’s Manual V1.
Step 12: Click on Finish button and all steps of setting printer server are completely. 7.4 System Management It has 6 sections: Change Password, Firmware Upgrade, Profiles Save, Time Zone Setting, UPnP Setting, and Language Setting. Making detailed settings are easier for users to setup. 258 User’s Manual V1.
7.4.1 Change Password Users can set or change their password in this section. Please enter the password and confirm it. Click on Apply Changes to save the setting data. Or you may click on Reset to clear all the input data. 259 User’s Manual V1.
7.4.2 Firmware Upgrade This function can upgrade the firmware of the router. There is certain risk while doing firmware upgrading. Firmware upgrade is not recommended unless the significant faulty is found and published on official website. If you feel the router has unusual behaviors and is not caused by the ISP and environment. You can check the website (http://www.etopnetwork.com.tw) to see if there is any later version of firmware.
7.4.3 Profiles Save The Profiles Save option lets user save and retrieve a file containing your router’s configuration settings Save it to a computer. Reset to default. Upload the file from PC to router. *Please see the following instructions. a. Please click Save…, a prompt window will ask user to save config.dat file. (Figure 1), please select the location (Figure 2), for example: the desktop (Figure 3). 261 User’s Manual V1.
(Figure 1 ) 262 User’s Manual V1.
(Figure 2) (Figure 3) b. Please click Browser… (Figure 1) and select the config.dat file. (Figure 2), and then click Upload to retrieve (Figure 3). 263 User’s Manual V1.
(Figure 1) (Figure 2) 264 User’s Manual V1.
(Figure 3) c. When you see the screen displaying like the following figure, it means update is completed. Please click OK to turn back to the configuration page. d. if you want to reset the system back to factory default settings, please click Reset button. 265 User’s Manual V1.
e. When you see the screen displaying like the following figure, it means reset is completed. Please click OK to turn back to the configuration page. 7.4.4 Time Zone Setting This function allows users to select their time zone and NTP server. Users can adjust the time manually or through the NTP server. 266 User’s Manual V1.
1. Current Time Users can input the time manually. 2. Time Zone Select Please select the time zone. 3. Enable NTP client update Please select to enable NTP client update or not. 4. Automatically Adjust Daylight Saving Please select to enable Automatically Adjust Daylight Saving or not. 5. NTP server Please select the NTP server from the pull-down list, or you can enter the NTP server IP address manually. 6. Apply Changes & Reset & Refresh Please click on Apply Changes to save the setting data.
7.4.6 Language Setting This page provides users with 12 languages to choose to do the interface configuration. Please click Apply Changes after selecting a language. 268 User’s Manual V1.
Please select the language. Using Korean as an example, the screen will display on the chosen language after the countdown is finished. Caution: After countdown, you can press Ctrl+F5 forcing the page to refresh. This can avoid any translation uncompleted situation. 7.4.7 User Account Management Personal users can use each individual application such as My Status, My Webcam and My Document. This section is to set the user’s right.
1. User Name Create the user name in this blank. 2. Password Setup the user’s password. 3. User Right Enable the use to Webcam, FTP or Samba server. 4. Apply & Cancel Click on Apply button to add the settings into the list table. Click on Cancel button to clean the setting on this page. 7.4.
do disk partition, and the Unplug button will appear. 2. To partition/format the disk, please select the disk and click on Format button. 3. If you want to view the data inside the disk, please click on “Disk Explorer” to view all the disks folders inside the device. Note：You have to click on “Unplug” button before remove the USB devices. 271 User’s Manual V1.
7.5 Log & Status The category provides Network Config and Event Log status for users to know the operation status. 7.5.1 Network Config Users can check the Internet status under this category, including Firmware version, Wireless setting, Connecting Time, WAN, TCP/IP …information. 272 User’s Manual V1.
7.5.2 Event Log You may enable the event log feature here. Please select to enable log function. 273 User’s Manual V1.
1. Enable Log You may choose to enable Event Log or not. 2. system all、wireless & DoS Please select the event you want to record. 3. Enable Remote Log You may choose to enable the remote event log or not. 4. Log Server IP Address Please input the log server IP Address. 5. Apply Changes & Refresh & Clear Click on Apply Changes to save the setting data. Click on Refresh to renew the system time, or on Clear to clear all the record.
This function provides users to logout. Click on Apply Change to logout. 275 User’s Manual V1.
Chapter 8 DDNS Account Setup DDNS is a service changes the dynamic IP to the static IP. For ADSL & Cable users, the settings of DDNS can solve the problem of being given the different IP by router every time. After setting the Router, your hostname would correspond to your dynamic IP. 【Step 1】 Please visit the website http://www.dyndns.com/, and click on Sign Up Now. 【Step 2】 Please fulfill the requested information at the column, and click on Create Account when finished.
【Step 3】 When the below window appears, you already finish the registration. Please check your E-mail box, and you will receive an e-mail from the DynDNS. 277 User’s Manual V1.
【Step 4】 Please open the email sent from DynDNS. Click on the link to confirm your account. 【Step 5】 Please click on login. 278 User’s Manual V1.
【Step 6】 Please click on My Services under the Account Summary for the linkage. 【Step 7】 Please click on Add Host Services. 279 User’s Manual V1.
【Step 8】 Please click on Add Dynamic DNS Host. 【Step 9】 1. Please input the account you applied. 2. Please select the hostname preferred at the drop-down menu. 3. Please click on Add Host to add the name. 1 2 3 【Step 10】 When the below window appears, it means your hostname is created. 280 User’s Manual V1.
Chapter 9 9.1 Q&A Installation 1. Q: Where can I find the IP and MAC address of my computer? A: (1) From the Start menu, select Run, an input box will appear with a flashing cursor. Type "cmd" or "Command" in the Run box (2) An MS DOS Window will open, please input ipconfig /all, and then press Enter. 281 User’s Manual V1.
You will see information about Ethernet adapter for Local Area Connection. • IP address (192.168.1.100)： This is the IP address of your computer. • Default Gateway (192.168.1.1) This is the Gateway IP address of your computer. • Physical Address (00-0D-61-37-66-ED) This is the MAC address of your network interface card. 1. Q: Where should I install the XDSL Router in a network environment? A: In a typical network environment, the router should be installed between XDSL network and Local Area Network.
2. Q: My network speed is very slow, why? A: Please make sure your network cable is less than 100m. Or you can install a bridge between your router and computer to keep the quality of signal. You can also try to…: Please make sure the network traffic is less than 37% of bandwidth. Please check to see there are no more than 10 broadcast messages in network traffic. Please check the network topology and settings. 9.2 LED lights 1.
9.3 IP Address 1. Q: What is the default IP address of the Server Router? A: The default IP address is 192.168.1.1, and the Subnet mask is 255.255.255.0。 2. Q: I don’t know my WAN IP address? A: There are two ways to find it. 1: Please check with your ISP. 2: Please select Log & Status on the left menu of the Server Router, and then select Network Configuration, you will see the WAN IP address. 3.
Check the network cable connection condition, or use another cable to test again. 2. Q: Why can’t I use the utility? A: Solution 1: Check out your Ethernet connection and power adapter. Solution 2: Make sure that the IP address of your computer is located between 192.168.1.2 and 192.168.1.254. The Subnet Mask should be 255.255.255.0. The default Gateway is 192.168.1.1. To confirm these settings, please follow the instructions below. Windows 95 or 98: 1. Click Start > Run > input winipcfg > click OK. 2.
2. Select Proxies > Select Direct connection to the Internet > Click on OK. 3. Q: The webpage browsing is frozen, disconnection during downloading, or un-readable text shown on my screen. What should I do? A: Right click on My Computer > Properties > select Device Manager on Hardware tab > right click on Network Adapters > select Properties > select Advanced tab > select Link Speed/Duplex Mode on the left, and choose 10Mbps/Half Duplex > click OK. 4.
1. Please check the power of Cable/XDSL modem. 2. Please check the connection of Cable/XDSL modem. 3. Check the LED status of WAN to make sure Cable/XDSL modem is connecting with Server Router. If your ISP requires username and password, please make sure they are correct. The ISP will use there to identify users if the network service uses DHCP without authentication. 5. Q: I can ping the computer outside the local area network, but I can’t use the Internet. A: Check the DNS settings on your computer.
connect to the Internet, unless it provide a specific name. It is similar to the network or workgroup name of the function of the region. When you encounter great difficulties in data transmission, it is better to keep the situation simple. You can disable all WEP encryption settings. The successful implementation of the encryption system includes a shared encryption key. The hex encryption key is commonly used. Encryption keys will allow the router to confirm workstations as trustable websites.
Location: Please adjust the location and direction of your router. Channel: Change to another channel can avoid the interruption. Interruption: It might be interrupted by other devices. You can turn off other devices first, and then reconnect. Any noisy device should be avoided or relocated. Shielding Effect: The speed might be impeded by your environment between wireless clients. Close to station is the only way to improve the speed. 4.
A: The default WEP of WinXP is Authentication Open System – WEP, but Server Router only has Pre-Shared Key – WEP. Please change WEP of WinXP to Pre-shared Key – WEP. 9.7 Supports 1. Q: What is the maximum value for Server Router to support IP address? A: Server Router supports 253 IP addresses under NAT mode. 2. Q: Is this Router compatible on different platform? A: It is compatible to any platform supports Ethernet and TCP/IP. 9.8 Others 1. Q: I always get disconnected on PPPoE mode.
For Extend other Extend SSID Access Point's Range For Extend other Access Point's Range For User Connecting 4. Q: I don’t see anything in My Webcam？ A: This function needs Java support; you can go to the following URL to download the Java application. http://www.java.com/zh_TW/download/index.jsp Chapter 10 Appendix 10.1 Operating System 1. Microsoft：Windows 2000, XP, Vista 32bit and the following related versions. 2. Apple：Mac OS X 10.4.7, Leopard and the following related versions. 3.
