E- TECH C o., Ltd 1/19 ▶ Table of Contents◀ 1. Introduction 2. Description of Unit 3. Technical Specifications 4. Theory of Operation 5. Circuit Descriptions 6. Alignment Procedure - FILE: IP 100 service manual.doc 2004.05.
E- TECH C o., Ltd 2/19 1. Introduction IP-100 has a compact size with a various features in the range of 136~174MHz. IP-100 Has a various features shown as below. IP-100 constructed with a microprocessor controlled, temperature compensated Phase Locked Loop(PLL) frequency synthesizer. The radio features a double conversion receiver and a direct FM transmitter modulator.
E- TECH C o., Ltd 3/19 3. Technical Specifications 3-1 General 1) Frequency range : 136~174 MHz 2) Channels : 255 Channels 3) Channel spacing : 12.5 kHz/25 kHz 4) Communication method : Simplex 5) Antenna Impedance : 50 ohm 6) : Helical Antenna Antenna 7) Power supply voltage : 8) Current Drain : LI-1700mAh Li-Ion battery pack(Voltage: 7.5V DC) When Transmitting(5W) - When Receiving(0.
E- TECH C o., Ltd 4/19 3-3 Receiver 1) Receiver Type : Double Super Hetero type 2) Sensitivity : -0.25uV 이하(12dB SINAD 시) 3) Frequency Stability : ±0.00025%(±2.5PPM) 4) SPURIOUS Rejection : 5) Adjacent Channel Selectivity: -60 dB -60 dB (Narrow) , -70 dB (Wide) 6) Distortion : 5% (1 kHz 60%) 7) Hum & Noise : -40 dB(HP8920A 300Hz ~ 3kHz BPF) 8) Audio output : 1000 mW 9) BAND SPREAD : 38MHz 10) Speaker size : 45 pi 4.
E- TECH C o., Ltd 5/19 4-1 Features & Operation 1. Monitor Press the Monitor key momentarily to disable the Tone squelch. 2. Radio Call By using Various 5Tone, individual / Group call is available. 16 Receiving codes are available as well as open call. 3. Missed calls list 16 Missed calls can be listed. If a call remains unanswered, the call will be stored by the radio. 4. contact list During a call, the contact list may be used to give access to up to 16 preprogrammed numbers accessed via the menu. 5.
E- TECH C o., Ltd 6/19 4-2 LCD Display and Icons 1.ANT GAZE ; Shows the received signal strength. 2.TX POWER HIGH: Indicate power level 3.KEY LOCK: Appears during key lock function is ON. 4.ALART(BEEP) ON/OFF: Appears when beep sound is turned ON. 5.Battery level indicator: Indicates reaming battery power. 6.VOX ON/OFF: Appears when VOX function is turned On. 7.SCAN: Appears when Scan function is activated. 8.SCRAMBLE: Appears while the voice scrambler function is activated. 9.TALK AROUND Indicator.
E- TECH C o., Ltd 7/19 3. Contact list 1). to enter Menu Mode. 2) or 3) 4) 5) to until to select or to scroll list to exit 4. Status call list 4-1. Making STATUS call 1) to enter Menu Mode. 2) or 3) 4) to until to select or to scroll list 5) Push PTT KEY for sending message on the LCD. 4-2 Make STATUS Message 1) to enter Menu Mode. 2) or 3) 4) 5) to until to select or to scroll list to SELECT FILE: IP 100 S ervice manual.doc 2004.05.
E- TECH C o., Ltd 8/19 5. Lone work 1). to enter Menu Mode. 2) or 3) to until to select or 4) to select ON/OFF 6. Tx power . 1). to enter Menu Mode. 2) or 3) to until to select or 4) 5) to select HIGH / LOW POWER to select 7. Tx Tone Selecting Transmitting TONE(CTCSS/DCS). 1). to enter Menu Mode. 2) or 3) 4) to until to select or to Select TONE을 either CTCSS or DCS. 0= NON TONE 1-38 CTCSS 101 – 183 DCS TONE 5) to select exit FILE: IP 100 S ervice manual.doc 2004.05.
E- TECH C o., Ltd 9/19 8. Rx Tone Changing Receiving TONE(CTCSS/DCS). 1). to enter Menu Mode. 2) or 3) to until to select 4) or to select TONE either CTCSS or DCS. 0= NON TONE 1-38 CTCSS 101 – 183 DCS TONE. to select exit 5) 9. Group Changing GROUP Tone. 1). to enter Menu Mode. 2) or 3) to select or 4) 5) to until to select scroll list to select exit 10. Beep on/off 1). to enter Menu Mode. 2) or 3) 4) 5) to until to select or to select on off .
E- TECH C o., Ltd 10/19 11. Key lock 1). to enter Menu Mode. 2) or 3) to until to select 4) or 5) to select key lock /unlock. to select 12. Squelch level 16 level is available. 0 = terminate sq function 1). to enter Menu Mode. 2) or 3) 4) 5) to until to select or to the scroll list to select exit 13. Auto Squelch 1). to enter Menu Mode. 2) or 3) 4) 5) to until to select or to select on /off . to select 14. Scan 1). to enter Menu Mode. 2) or 3) to until to scan.
E- TECH C o., Ltd 11/19 4) Push PTT for exit 15. DTMF 1). to enter Menu Mode. 2) or 3) to until to select or 4) 5) to select ON /OFF. to select 16. Vox on/off 1). to enter Menu Mode. 2) or 3) to until to select or 4) 5) to select ON /OFF. to select 17. Vox Level 16 level is available.. 1). to enter Menu Mode. 2) or 3) 4) 5) to until to select or to select to scroll list for exit FILE: IP 100 S ervice manual.doc 2004.05.
E- TECH C o., Ltd 12/19 18. Auto Vox 1). to enter Menu Mode. 2) or 3) 4) 5) to until to select or to select ON /OFF. to select 19. Priority Scan 1). to enter Menu Mode. 2) or 3) 4) 5) to until to select or to select ON /OFF. to select 20. Priority scan CH 1). to enter Menu Mode. 2) or 3) 4) 5) to until to select or to scroll list to select for exit FILE: IP 100 S ervice manual.doc 2004.05.
E- TECH C o., Ltd 13/19 21. Power save 1). to enter Menu Mode. 2) or 3) to select or 4) 5) to until to select ON /OFF. to select 22. Talkaround 1). to enter Menu Mode. 2) or 3) 4) 5) to until to select or to select ON /OFF. to select 23. Password 1). to enter Menu Mode. 2) or 3) 4) 5) to until to select or to select ON /OFF. to select FILE: IP 100 S ervice manual.doc 2004.05.
E- TECH C o., Ltd 14/19 24. Password CH 1). to enter Menu Mode. 2) or 3) to until to select 4) ---- will display on the LCD( enter old password) or by pushing up and down KEY to change password. by pushing enter KEY to change digit of password. 5) Enter new password by 4 digit. 25. Location Indicate where the radio is located by blinking green light every 7 seconds. 1). to enter Menu Mode. 2) or 3) 4) 5) to until to select or to select ON /OFF. to select 26. Scramble 1).
E- TECH C o., Ltd 15/19 27. Status call Send 1). to enter Menu Mode. 2) or 3) to until to select or 4) 5) to select ON /OFF. to select 5. Circuit Description. 5-1 Transmitter 1) MIC AMP Circuit Voice signal from the microphone are applied to microphone amplifier U303. U303 contains a low-pass filter that has a 6dB/oct response between 300Hz and 3kHz and eliminate above 3kHz. The pre-emphasized audio signal is applied to VR302 to adjust maximum frequency deviation.
E- TECH C o., Ltd 16/19 4) IF Circuit The first signals from Q102 are fed to the matched pair crystal filter FL101, then IF signals are amplified in Q103. And those signals are fed to U101 which is composed of the second local oscillator, second local oscillator, second mixer, limiter amplifier, quadrature detector and active filter circuit. The second local oscillator at 20.945MHz with X 101 and is fed to the second mixer with the first IF signals to convert into 455kHz second IF signals.
E- TECH C o., Ltd 6. 17/19 Alignment 6-1 Alignment point FILE: IP 100 S ervice manual.doc 2004.05.
E- TECH C o., Ltd 18/19 6-2 Voltage Check 1) Set up the radio frequency to (136.025[Mhz]) then measure whether R/Tx voltage is over 0.8[v]. 2) Set up the radio frequency (173.975[Mhz]) then measure whether R/Tx voltage is under 5[v]. 3) When Un-Lock is display on LCD means defective goods. 6-3 Transmitter 1) At the frequency range of (146.025[MHz]), set up Tx mode then adjust frequency by using VR 301 at the level of ±150[Hz]. High power should be 3.8~5.5[W].