-Tool user's manual Product Name:E-Tool Model:EL-400D
Table of Contents 1. -Tool Introduction …………….…………………………………1 2. -Tool keypad Instruction ………….….……………………….. 2 3. Setting ……………………………………. …………….…………... 3 4. Diagnose Sensor Function……………………………………….. 4 5. Auto Duplicate Function …………………………………...…….. 6 6. Manual Duplicate Function …………………..…………………... 7 7. Program Blank Sensor Function…………………………….…... 8 8. Whole Car Learning…………………………………………….….. 9 9. Wireless ID/RL Modify…………………...………………………..
1. -Tool Introduction Indicator will turn red when battery is low. Indicator will turn red when charging. -Tool is designed to diagnose and interacts with sensor through wireless (radio frequency). The functions of sensor include: 1. Retrieve data from sensor mounted on the wheels. 2. Verify the identity of sensor mounted on the wheels. D-Sub is to connect with E-Cable. DC jack is to connect with adapter for charging. Mini USB is to connect with PC for software update.
2. -Tool keypad Instruction Power On/Off. Enter key, press enter to select function or validate a parameter. Navigate through measured and parameters. Esc key, press to return to the previous menu without parameter validation.
3. Setting Displays E-LEAD logo. Press ESC menu page. key on CAR MAKER to go to Choose SETUP and enter 3-1. Language: Use the “Enter” key to select. key to choose the language you prefer. 3-2. Temperature: Use the “Enter” key to choose between Fahrenheit and Celsius. 3-3. Pressure: Use the “Enter” 3-4. Format: Use the “Enter” key to choose key to choose between PSI, Bar and kPa. ID format between decimal and Hexadecimal. 3-5 .
3-9. SN: SN is -Tool’s serial number for software update. 3-10 Checksum: It is for engineering check. 3-11 version: VERSION is -Tool’s Firmware version.. 4. Diagnose Sensor Function 1. Press and hold the power key to power on the device and the device displays E-LEAD logo. Long press to turn on the device. Displays E-LEAD logo. Choose car maker by using arrow key to browse alphabets. Press enter key to select. Use arrow key to browse automakers. Press enter key to select.
Use arrow key to select DIAGNOSE SENSOR and press enter key to diagnose. -Tool will activate the sensor. The sensor respond time may vary depending on sensor type and brand. -Tool will beep after receiving sensor information. The picture below is an example of diagnose result: Notes Not all sensors transmit every piece of information shown.
5. Auto Duplicate Function This function is designed for you to duplicate an O.E sensor’s ID and program a new sensor. Choose car maker by using arrow key to browse alphabets. Press enter key to select. Use arrow key to browse automakers. Press enter key to select. Use arrow key to browse models. Press enter key to select. Use arrow key to browse year. Press enter key to select. Use arrow key to select AUTO DUPLICATE and press enter key to select. -Tool will display the O.
-Tool will program the sensor. You will hear 2 short beeps when programming successfully. 6. Manual Duplicate Function This function is designed to duplicate an O.E senor’s ID by keying in its ID. If -Tool cannot detect sensor, you can put senor’s ID into it. Choose car maker by using arrow key to browse alphabets. Press enter key to select. Use arrow key to browse automakers. Press enter key to select. Use arrow key to browse models. Press enter key to select. Use arrow key to browse year.
Please connect E-Cable. -Tool with -sensor by -Tool will program the sensor. You will hear 2 short beeps when programming successfully. 7. Program Blank Sensor Function This design is to program a new ID to a new from OE sensor. -sensor, once you cannot get ID Choose car maker by using arrow key to browse alphabets. Press enter key to select. Choose car maker by using arrow key to browse alphabets. Press enter key to select. Use arrow key to browse models. Press enter key to select.
Use arrow key to select PROGRAM BLANK SENSOR and press enter key to select. After programming a blank sensor, the new ID will display. 8. Whole Car Learning This function is designed for getting all O.E. sensor’ ID on the car at one go and then copying the ID to target sensors on the car at one go. Please note that the target sensors are required to have protocol inside. 8.1 Read All This design is to get all O.E. sensor’s ID on the car at one go. Choose car maker by using arrow key to browse alphabets.
Use arrow key to select READ ALL and press enter key to select. Please scan the sensor from left front, left rear, right rear, right front tire and spare tire in order. After scanning sensors, -Tool will save the data. The maximum storage is 25 pcs of sensor’s data. We suggest saving data to PC. 8.2. WRITE ALL This function is designed for copying the ID to target sensors on the car at one go.
After showing the data storage status, press to copy ID to target sensors on the car at one go. Use arrow key to select WRITE ALL and press enter key to select. Use arrow key to select Enter=duplicate and press enter key to select. After changing the tires, put -Tool closely near left front, left rear, tire and press to copy the ID to target sensor.
9.Wireless ID/RL Modify This function is to design for copying O.E sensor to target Senor. Please note the target sensor is required to have the same protocol as O.E sensor. Choose car maker by using arrow key to browse alphabets. Press enter key to select. Choose car maker by using arrow key to browse alphabets. Press enter key to select. Use arrow key to browse models. Press enter key to select. Use arrow key to select WIRELESS ID/RL MODIFY and press enter key to select. 9.
-Tool will show OE sensor’s ID then you can press key to copy the ID to target sensor. Please place target sensor near -Tool. You will hear 2 short beeps when it is done. 9.2 Manual ID Modify Function Use arrow key to choose MANUAL ID MODIFY. Press enter key to select. Scan O.E. sensor wirelessly. -Tool will show OE sensor’s ID and press modify the ID. Use arrow key to browse and press Complete Modification. 13 to to select.
14
