Head up Display User Manual Thank you for purchasing the Head Up Display! The User Manual will teach you how to operate the product. Please read the User Manual before starting using the product to make sure you operate the HUD correctly.
Safety Warning The product operates safely as a design and manufacture were given priority in development. To avoid any potential risks, please follow the instructions when you are going to install, operating and cleaning the product. ● Before using the product, please read and understand all instructions, and save all instructions as they may be useful in the future. ● You are required to follow all warning instructions for the product.
Federal Communication Commission Interference Statement This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. FCC RF Radiation Exposure Statement: This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. End users must follow the specific operating instructions for satisfying RF exposure compliance.
Product Introduction 一、Product outline(EL-311R) 5
一、Product Outline(EL-101) 麥克風口:microphone input/多元化顯示螢幕: Multiple Display Layout SCreen Micro SD卡槽: Micro SD input / 行車記錄器影像輸入:Entering for Digital video recording 倒車鏡頭影像輸入: Entering for Reversing monitor view 二、Product features ● 4” TFT high-resolution image with multiple display layouts, information full, bright screen but does not hurt the eyes. ● Lighting sensor: automatic detection when light reaches the sensor. ● Special and newly innovative GPS built-in/ with speeding reminding.
三、Specification Voltage DC 12V Storage Temperature -40℃ ~ +85℃ Working temperature -30℃ ~ +80℃ Current consume Single operation 1A/ with event data record 2.5A After turning off car engine, the products current consume ≦0.13mA 311 overall size (body) Length 122.2mm*Width111.4mm*height 29.7mm 311R overall size (body with Length146.3mm*Width116mm*Height17.
四、Instructions for starting the Product [Preface] Before using the product, please follow the procedures in order to sure the regular connections.
Connect Setting(Android System) Procedure 1 Install E-where on your phone and EZ-Remote APP。E-where APP function when you are doing route planning, you can share all hot spot (scenery) to SmartHUD. EZ-Remote is an app that functions as a remote controller for the HUD monitor.
Procedure 3Enable the blue tooth function:Setting>Bluetooth>Open,Choose console equipped 「Smart HUD」,Enter password 「1234」。 When building a connection, SmartHUD will ask for confirmation to make sure you want to give the telephone saving authorization.
Connection Setting(iOS System) Procedure 1 Install E-where on your phone and EZ-Remote APP。E-where APP function when you are doing route planning, you can share all hot spot (scenery) to SmartHUD. EZ-Remote is an app function its can control HUD monitor.
Procedure3 Enable Cellular:Settings>Cellular >Cellular Data 13
Procedure 4 Enable Personal Hotspot:Settings>Personal Hotspot>Personal Hotspot 14
Note:How to make sure the PAN is connected? You can get information about the Data connection or wireless base station is enabled* from mobile phone information.
After establishing PAN, you can enable EZ-Remote operation, press for one second and it will jump out another window, then screen down to gesture operation is the same as using a Mouse Mode.
Note: EZ-Remote will present functional teaching during first installation. Click on the EZ-Remote right side can review the functional teaching again after completing installation. Note: When EZ-Remote is in digital video record mode or safe mode, use long press follow by a down gesture to go back the main screen, do not use go back gesture to go back to the 17 primary links.
Knob Operating Gesture Display Response 1 second long press Enter to primary links 3 seconds long press Start voice control Short press Go to Enter Function Short Press+Long press Start EZ-Talk (program is developing) left rotate/right rotate Focus to left/right Press down+ rotate left Focus move up area 18
Press down+ rotate right 1. Digital Video Record(DVR) Select Primary links Focus move down area equipped with 311 type function,switch to DVR vision. Also you can use actuated button function of DVR to fast entering main menu. HOME Button Long time press:Enter to primary links ▲ Button long press: DVR and image recognition vision switch.
1、 Digital Video Recording(DVR) Select primary links equipped with 111 type function, switch to DVR screen. (The details of operating instruction please refer to EL-640-HUD1 manual.
2.
Road name of two blocks ahead Road name of one block ahead. Current speed limit (Red circle will flash while speeding) Driving Directions Current Temperature Highest temperature today Current driving speed Lowest temperature today Current road name Note: The triangles in the upper right corner indicate how close you are to your destination or next direction change. The first triangle will indicate to you at 200m to the destination.
The distance of one block ahead Driving Directions Current speed limit. Red circle will flash while speeding. Current speed limit Distance to destination Current road name • GPS Positioning Status: This icon located at the bottom right of the main screen informs you on your GPS status and connectivity. After setting a course, if your GPS status is fully connected the GPS icon will change from to current time. This indicates that your inputs were successful.
Screen of freerun Location at the map information can not support. After setting location in route planning set-up the photo shows up as follows.
※Select equipped Digital Video Recording (DVR) add-value function Without Route-planning and connected DVR layout 25
Road name of one block ahead. Distance of one section ahead Driving Directions Current speed limit, Red circle will flash while speeding.
Name of road one section ahead. The distance of one section a head Driving Directions Directions to next Current speed limit, The indicator will direction or course flash when you are speeding. Distance to Destination Current speed limit Current Weather Current road section with road name 三、Navigation For more details info please refer to navigation user manual.
Using Google Maps to Share Scenic Areas (Android System) or pick a specific scenic area with Step 1: Connect to Google Map address) Step 2: Look for scenic area (enter address or location into the search bar 28
Step 3: Sharing the Scenic Area Step 4: Sharing to Smart HUD 29
“Success” view Failure view “Cannot send POI” 30
Using Apple Maps to Share Scenic Areas (iOS System) Step 2: Allow E-Where to use your current Step 1: connect phone E-Where location, so you are able to continue.
need. Step 3: Initial view after E-Where has accessed your current location.
place in map. Click the address row for detail spot information. View of “Send Successully” Step 6: Click the icon for sharing spot to SmartHUD.
View of “No device connected”.
四、Applications Content: Weather:Resourced from Yahoo Weather News:Resourced from Yahoo News SD Music:Support for playing with Micro SD card MP3 and WAV music EZ-Talk and calendar function are under development.
(一)Weather Default weather information if not using GPS location is 1: Alabama city, 2: Taipei city. For other cities information you can select to enter another city and select this city. After the selection, you are able to set the cities you would like to display.
(二)News Default setting is instant news, to switch to a different setting, click page.
(三) SD Music This icon go back one folder, is used to update data.
五、Blue tooth Provide PhoneBook, music, message function Note: iOS system is not supported for blue tooth message function. (一 一) PhoneBook Top right of screen is ,used to update your contact info to the PhoneBook.
updating image layout to inform you, and the default operational layout for an incoming phone call below left photo. If phone number is not within Contact list it will be presented as unknown. During this interim screen the console is unable to show the other functions.
Select at top right ,updates and retrieves all new messages.
Provides a speeding reminder service using a Flashing function, and you can set the value from 0. The setting range is 50~50. You can add or subtract 1 Use + and - .
(2)Brightness The product auto detects outside light to automatically switch screen presentation. As personal preference you can switch by yourself, switch range is -5 to + 5. Add or subtract by 1, use + and -. (3) FM Transmitter The ability to use FM transmitter to listen to FM channels, using the car's video player's channels and switch to listen to HUD music signal. (FM range: 88.1-107.
(4) Voice volume Change to your personal preference. Use + and – to switch. As right photo example. (5) Language According your personal preference you can set the language. The console support English, Traditional Chinese and Simplified Chinese, use photo as an example.
7. Voice Recognition Voice recognition will give you an option to say a command or cancel, speak into the microphone to access different functions. How to start voice recognition: Knob:long press 3 seconds EZ-Remote:long press 1 second and slide to the right After start, system will play indicated words, such as ‘Say a command or cancel.
(1)Phone book Before using this function, please have your phone to connect with Bluetooth and go to the phonebook page to download contact lists first, then you would be able to start using this function. If you haven't finished connecting, then the screen will show you haven't connect the Bluetooth as indicated(example to the right) 1. After a short beep along with indication words ”please say a command or cancel”, give order “phonebook”. 2.
(2)Number calling To use this function, please have your phone to connect with Bluetooth. 1. After a short beep along with indication words ”please say a command or cancel”, give order “call”. 2. After a short beep along with indication words “Please say a number”, say the number clearly you want to call. Then system will show the result after recognition. 3. After a short beep along with indication words “Please say Dial or Correction “, give your order or cancel. 4.
(3) Mode Recog 1. After a short beep along with indication words “Please say a command or cancel”, give order “mode recog”. 2. After a short beep along with indication words ”please say a name”, give your order or cancel. 3. Say “safety”, then you can access to safety mode. 4. Say “DVR”, then you can enter the DVR mode.
(4) Siri 1. This function is only available for iOS systems 2. After a short beep along with indication words ”please say a name”, give order “Siri”, then system will reach Siri functions on your smartphone. 3. Recording page as right example. (5)Listen News 1. After a short beep along with indication words ”please say a name”, give order “Listen News”, you will access the news page and directly start speaking news text from first one.
Troubleshooting Version checking( the page only avalible for EL-311(R) instruction) Step 1:Please enter to primary links/setting /language's screen Step2:Please practice how to use actuated button turn left move, and select a target toward to up one space gesture. Step 3:Please practice using rotated button turn right move, then select a target to move down once space gesture.
Please inform the Service Specialist of your version number to let them solve your problem as soon as possible. System Programs Automatic Updates Step1:Please put update program on a Micro SD, please notice you are not allowed to put same profile name on the same card, if you do this you be unsuccessful when updating. Step2:Put Micro SD card inside the console's SD card slot, And at the same time turn off your car.
Step5:When screen switch the normal starting layout you are able to begin using the console.