E-SA18 MKBT_A6_quer_RZ_Okt.qxp_Layout 1 30.09.
E-SA18 MKBT_A6_quer_RZ_Okt.qxp_Layout 1 30.09.21 09:47 Seite 2 DYNAVOX ESA-18 MK BT Wir danken Ihnen für das Vertrauen, welches Sie uns durch die Entscheidung für dieses Audio-Produkt entgegenbringen. Dieses Gerät entspricht allen festgelegten internationalen Sicherheitsstandards. Trotzdem sollten die Sicherheitshinweise beachtet werden, um eine Gefährdung zu vermeiden.
E-SA18 MKBT_A6_quer_RZ_Okt.qxp_Layout 1 30.09.
E-SA18 MKBT_A6_quer_RZ_Okt.qxp_Layout 1 30.09.21 09:47 Seite 4 SICHERHEITSHINWEISE Alle Betriebsmittel, die an die Netzspannung des Haushalts angeschlossen sind, können dem Benutzer bei unsachgemäßer Behandlung gefährlich werden. Das Gerät darf nicht geöffnet werden! Gefahr des elektrischen Schocks! Überprüfen Sie regelmäßig die technische Sicherheit des Gerätes.
E-SA18 MKBT_A6_quer_RZ_Okt.qxp_Layout 1 30.09.21 09:47 Seite 5 SICHERHEITSHINWEISE Ziehen Sie stets am Netzstecker und nie am Netzkabel, wenn Sie die Verbindung zum Stromnetz trennen wollen. Stellen Sie sicher, dass das Netzkabel nicht gequetscht, extrem gebogen oder durch scharfe Kanten beschädigt wird. Fassen Sie das Netzkabel nicht mit nassen oder feuchten Händen an. Achten Sie darauf, dass das Gerät nicht mit Flüssigkeiten, Feuchtigkeit, Regen oder Wasserdampf in Berührung kommt.
E-SA18 MKBT_A6_quer_RZ_Okt.qxp_Layout 1 30.09.21 09:47 Seite 6 WEITERE HINWEISE Elektronik Altgeräte CE-Zeichen Dieses Gerät unterliegt den Bestimmungen der EURichtlinie 2012/19/EU, deren gesetzliche Umsetzung in Deutschland durch das Elektro- und Elektronikgeräte-Gesetz (ElektroG) geregelt ist. Dies ist durch das Symbol eines durchgestrichenen Abfalleimers auf dem Gerät gekennzeichnet.
E-SA18 MKBT_A6_quer_RZ_Okt.qxp_Layout 1 30.09.21 09:47 Seite 7 WEITERE HINWEISE Dynavox arbeitet ständig an der Verbesserung und Weiterentwicklung seiner Produkte. Deshalb bleiben Änderungen an Design und technischer Konstruktion des Gerätes, sofern sie dem Fortschritt dienen, vorbehalten. Der Inhalt dieser Anleitung hat lediglich Informationscharakter. Er kann jederzeit ohne vorherige Ankündigung geändert werden und stellt keine Verpflichtung seitens des Markeninhabers dar.
E-SA18 MKBT_A6_quer_RZ_Okt.qxp_Layout 1 30.09.
E-SA18 MKBT_A6_quer_RZ_Okt.qxp_Layout 1 30.09.21 09:47 Seite 9 1. POWER Schaltet das Gerät ein und aus. Das Gerät ist im ausgeschalteten Zustand vom Netz getrennt. Im eingeschalteten Zustand leuchtet die neben dem Schalter angebrachte LED. 5. BASS Zur Einstellung der Bassanteile (Tiefen) des Klangs. 6. TREBLE Zur Einstellung der Höhenanteile (Höhen) des Klangs. 2. MIC INPUT An diese 6,3 mm Klinkenbuchse können Sie, wenn gewünscht, ein dynamisches Mikrofon anschließen.
E-SA18 MKBT_A6_quer_RZ_Okt.qxp_Layout 1 30.09.
E-SA18 MKBT_A6_quer_RZ_Okt.qxp_Layout 1 30.09.21 09:47 Seite 11 11. AUDIO INPUT Hier können ein oder zwei Quellgeräte mit Stereoton-Hochpegelausgang angeschlossen werden, deren Signale im Verstärker zusammengemischt werden. 14. TO SPEAKER Ausgangsbuchsen mit Schraubklemmen zum Anschluss eines Lautsprecherpaars. Es können Lautsprecherkabel mit 4 mm Bananensteckern verwendet werden. 12. PRE OUT Schließen Sie hier, wenn gewünscht, z.B. einen Subwoofer oder ein Aufnahmegerät an.
E-SA18 MKBT_A6_quer_RZ_Okt.qxp_Layout 1 30.09.21 09:47 Seite 12 TYPISCHES KARAOKE-SYSTEM Für ein typisches Karaokesystem verbinden Sie den Hochpegelausgang eines Wiedergabegerätes für die Hintergrundmusik (CD-Player, Computer, portabler Player etc.) unter Verwendung eines Cinchkabels mit einem der Eingänge „AUDIO INPUT“ oder verwenden die BT-Verbindung. An die Mikrofoneingangsbuchse „MIC IN“ an der Gerätevorderseite schließen Sie ein dynamisches Mikrofon an.
E-SA18 MKBT_A6_quer_RZ_Okt.qxp_Layout 1 30.09.
E-SA18 MKBT_A6_quer_RZ_Okt.qxp_Layout 1 30.09.21 09:47 Seite 14 ANSCHLUSS UND INBETRIEBNAHME Stellen Sie die Kabelverbindung in der nachfolgend genannten Reihenfolge her.
E-SA18 MKBT_A6_quer_RZ_Okt.qxp_Layout 1 30.09.21 09:47 Seite 15 ANSCHLUSS UND INBETRIEBNAHME Anschluss der Lautsprecher Es ist empfehlenswert, konfektionierte Lautsprecherkabel zu verwenden, anstatt die Innenleiter (Litze) der Kabel direkt anzuklemmen. Bananenstecker oder Kabelschuhe bieten höhere Sicherheit gegen Kurzschlüsse und Beschädigung der Lautsprecher oder des Verstärkers. Benutzen Sie für die Verbindung Ihrer Lautsprecher mit dem ESA-18 MK BT ein Kabel mit ausreichendem Querschnitt.
E-SA18 MKBT_A6_quer_RZ_Okt.qxp_Layout 1 30.09.21 09:47 Seite 16 ANSCHLUSS UND INBETRIEBNAHME ähnliche Anschlüsse, auch hier ist die Polarität angegeben. Hier wird das andere Ende des dem Lautsprecher zugeordneten Lautsprecherkabels angeschlossen. Durch das Lautsprecherkabel müssen jeweils gleichartige Anschlüsse eines Klemmenpaares miteinander verbunden werden: die mit „+“ markierte Klemme am Verstärker muss zum mit „+“ markierten Anschluss des Lautsprechers führen.
E-SA18 MKBT_A6_quer_RZ_Okt.qxp_Layout 1 30.09.21 09:47 Seite 17 BEDIENUNG DES GERÄTES Aktion Ein- und Ausschalten Taste(n) POWER (1) Beschreibung Das Gerät wird an der Gerätevorderseite ein- und ausgeschaltet. Ist der Schalter in der Ausschaltposition, ist das Gerät vom Stromnetz getrennt. Im eingeschalteten Zustand leuchtet die neben dem Netzschalter angeordnete LED. Vor dem Einschalten sollte vorsichtshalber die Lautstärkeeinstellung (10) reduziert werden.
E-SA18 MKBT_A6_quer_RZ_Okt.qxp_Layout 1 30.09.21 09:47 Seite 18 Aktion Taste(n) Beschreibung die Lautstärke (10) verringert werden. HIGH = normale, für Hochpegelquellen geeignete Empfindlichkeit LOW = niedrigere Empfindlichkeit für kräftigere Eingangssignale Höhenanteile des Klangs verändern TREBLE (6) Mit dem Drehregler „TREBLE“ an der Gerätevorderseite beeinflussen Sie den Anteil der höheren Töne des Klangbilds.
E-SA18 MKBT_A6_quer_RZ_Okt.qxp_Layout 1 30.09.21 09:47 Seite 19 Aktion Taste(n) Beschreibung notwendig, weil das menschliche Gehör bei niedriger Lautstärke hohe und tiefe Frequenzanteile bei identischem Schalldruck viel leiser wahrnimmt als die Mitten (Tonfrequenzen um 1 kHz). Diese Funktion sollte nur bei niedriger Lautstärke verwendet werden.
E-SA18 MKBT_A6_quer_RZ_Okt.qxp_Layout 1 30.09.21 09:47 Seite 20 Aktion Taste(n) Beschreibung 0.4 Watt auf. Um das Gerät danach wieder einzuschalten, muss der Ein/Ausschalter zwei mal betätigt werden. Einen Standby- bzw. Bereitschaftszustand besitzt dieses Gerät nicht. Bei längerer Nichtnutzung empfiehlt es sich grundsätzlich das Gerät vom Netz zu trennen. Die automatische Standbyschaltung kann mit dem Schalter A-S (ON/OFF) auf der Geräterückseite deaktiviert werden.
E-SA18 MKBT_A6_quer_RZ_Okt.qxp_Layout 1 30.09.21 09:47 Seite 21 TECHNISCHE DATEN Frequenzgang: Nennausgangsleistung (Musikleistung) an 4 Ohm: Eingangsempfindlichkeit (Cincheingang): 20 Hz - 20 kHz (3dB) 2 x 75 W 150 mV („SIGNAL IN“=HIGH) 300 mV („SIGNAL IN“=LOW) 10 mV < 0.
E-SA18 MKBT_A6_quer_RZ_Okt.qxp_Layout 1 30.09.21 09:47 Seite 22 DYNAVOX ESA-18 MK BT We thank you for the confidence you prove in purchasing our product. It complies with all established international safety standards. Nonetheless, the following instructions should be fully read and observed in order to prevent any hazard: In order to ensure correct operation, please read these instructions thoroughly before setting up and connecting this device.
E-SA18 MKBT_A6_quer_RZ_Okt.qxp_Layout 1 30.09.21 09:47 Seite 23 DYNAVOX ESA-18 MK BT The ESA-18 MK BT is a compact HiFi amplifier for two stereo RCA input sources, BT and a microphone. If two analog sources are connected to the RCA inputs, their signal will be mixed. There is no option to switch between the two sources. If a dynamic microphone is connected, its signal will be mixed with the signal from sources depending on the setting of the microphone volume (2) (karaoke function).
E-SA18 MKBT_A6_quer_RZ_Okt.qxp_Layout 1 30.09.21 09:47 Seite 24 SECURITY PRECAUTIONS All equipment that is connected to the domestic mains voltage can be dangerous to the user if not handled properly. Do not open the appliance! Risk of electric shock! Regularly check the technical safety of the device.
E-SA18 MKBT_A6_quer_RZ_Okt.qxp_Layout 1 30.09.21 09:47 Seite 25 SECURITY PRECAUTIONS Always pull the plug and never the power cable if you want to disconnect the appliance from the mains power. Make sure when setting up the appliance that the power cable is not squashed, severely bent or damaged by sharp edges. Do not touch the power lead with wet or damp hands.
E-SA18 MKBT_A6_quer_RZ_Okt.qxp_Layout 1 30.09.21 09:47 Seite 26 USER INFORMATION Electronic waste CE-Sign This appliance is subject to the conditions set out in the European Directive 2012/19/EU, whose implementation is regulated in Germany by the Electrical and Electronic Equipment Act (ElektroG). This is identified by the symbol of a crossed out waste bin on the appliance.
E-SA18 MKBT_A6_quer_RZ_Okt.qxp_Layout 1 30.09.21 09:47 Seite 27 USER INFORMATION Dynavox works continually to improve and develop its products. Therefore, the appearance and technical design of the appliance are subject to changes, as long as they are in the interest of progress. Dynavox is a registered trademark of Sintron Distribution GmbH, 76473 Iffezheim.
E-SA18 MKBT_A6_quer_RZ_Okt.qxp_Layout 1 30.09.
E-SA18 MKBT_A6_quer_RZ_Okt.qxp_Layout 1 30.09.21 09:47 Seite 29 1. POWER Switches the device on and off. When switched off, the device is disconnected from the mains. The LED located next to the switch lights up when the device is switched on. 5. BASS For setting the bass proportions (low frequencies) of the sound. 6. TREBLE For setting the treble proportions (high frequencies) of the sound. 2. MIC INPUT You can connect a dynamic microphone to this 6.3 mm jack socket.
E-SA18 MKBT_A6_quer_RZ_Okt.qxp_Layout 1 30.09.
E-SA18 MKBT_A6_quer_RZ_Okt.qxp_Layout 1 30.09.21 09:47 Seite 31 11. AUDIO INPUT Here you can connect one or two source devices with stereo audio high level output and their signals are mixed to the amplifier. 14. TO SPEAKER Output sockets with screw clamps for connecting one pair of loudspeakers. Loudspeaker cables with 4 mm banana connectors may be used. 12. PRE OUT If desired, attach a recording device or subwoofer here, for example.
E-SA18 MKBT_A6_quer_RZ_Okt.qxp_Layout 1 30.09.21 09:47 Seite 32 TYPICAL KARAOKE SYSTEM For a typical karaoke system connect the high level output of an audio source for the playback music (CD player, computer, portable player etc.) using an RCA cable with one of the inputs being “AUDIO INPUT” or use the BT connection. Connect a dynamic microphone to the microphone input socket “MIC IN” on the front of the device.
E-SA18 MKBT_A6_quer_RZ_Okt.qxp_Layout 1 30.09.
E-SA18 MKBT_A6_quer_RZ_Okt.qxp_Layout 1 30.09.21 09:47 Seite 34 CONNECTION AND PLACING INTO OPERATION Make the cable connections in the order specified below. Never make changes to the cable connections while the devices are switched on! Mechanically identical RCA plugs are available for input and output connections. Make sure that you do not get these connections confused during installation! Make sure that you do not mix up the analogue inputs for right and left.
E-SA18 MKBT_A6_quer_RZ_Okt.qxp_Layout 1 30.09.21 09:47 Seite 35 CONNECTION AND PLACING INTO OPERATION input (“LINE IN”, “TAPE IN” or “REC IN”) of the recording device or a subwoofer. your loudspeakers with the ESA-18 MK BT. Make sure that bare loudspeaker cables can never touch each other or the back wall of the housing! Only use loudspeakers with a nominal impedance of at least 4Ω. One pair of loudspeakers may be connected to the amplifier.
E-SA18 MKBT_A6_quer_RZ_Okt.qxp_Layout 1 30.09.21 09:47 Seite 36 CONNECTION AND PLACING INTO OPERATION cables with 4 mm banana connectors, you need to connect only the two plugs of each loudspeaker cable with the two associated clamps and the screw cover of the clamp should be turned in a clockwise direction.
E-SA18 MKBT_A6_quer_RZ_Okt.qxp_Layout 1 30.09.21 09:47 Seite 37 OPERATING THE APPLIANCE Operation Button(s) Description Switch on and off POWER (1) The amplifier is switched on and off using this button at the front panel. When switched off the device is internally separated from the AC power. The LED next to the mains switch lights up when the device is switched on. As a precaution, after switching on, the volume setting (10) should be reduced.
E-SA18 MKBT_A6_quer_RZ_Okt.qxp_Layout 1 30.09.21 09:47 Seite 38 OPERATING THE APPLIANCE Operation Button(s) Description Change the treble proportions of the sound TREBLE (6) With the “TREBLE” control dial on the front of the device you affect the proportion of higher frequencies in the sound. Turning it in clockwise direction increases the treble intensity and moving it in anticlockwise direction reduces it. In the middle setting the treble proportions of the input signals remain unchanged.
E-SA18 MKBT_A6_quer_RZ_Okt.qxp_Layout 1 30.09.21 09:47 Seite 39 OPERATING THE APPLIANCE Operation Button(s) Description Mix in a microphone signal MIC VOL (3) With this dial you change the volume of the microphone signal and thereby determine how loud the microphone signal is in the final mix with the sources (karaoke function). If no microphone is used, it is recommended that the dial be set to its minimum.
E-SA18 MKBT_A6_quer_RZ_Okt.qxp_Layout 1 30.09.21 09:47 Seite 40 OPERATING THE APPLIANCE Operation Button(s) Description Input sources BT/LINE (8) To use the BT function, set the input selector switch (8) BT/LINE to "BT" channel. The blue LED starts flashing and signals the connection availability. Now locate the amplifier in the list for available devices with your BT-compatible source device. You can find more information in the operating instruction of your source device.
E-SA18 MKBT_A6_quer_RZ_Okt.qxp_Layout 1 30.09.21 09:47 Seite 41 TECHNICAL SPECIFICATIONS Frequency Response: Nominal output power (music power) into 4 Ohm: Input Impedance (RCA inputs): 20 Hz - 20 kHz (3dB) 2 x 75 W 150 mV („SIGNAL IN“=HIGH) 300 mV („SIGNAL IN“=LOW) 3 mV < 0.
E-SA18 MKBT_A6_quer_RZ_Okt.qxp_Layout 1 30.09.21 09:47 Seite 42 DYNAVOX ESA-18 MK BT Nous vous remercions de la confiance que vous nous témoignez en achetant ce produit de qualité. Cet appareil répond à toutes les normes internationales de sécurité qui doivent être respectées pour éviter tout danger. Pour garantir une mise en service conforme, veuillez lire entièrement cette notice avant d’installer et raccorder votre appareil.
E-SA18 MKBT_A6_quer_RZ_Okt.qxp_Layout 1 30.09.21 09:47 Seite 43 amplificateur le signal (qui peut aussi être entendu via les haut-parleurs) peut être retransmis à un appareil enregistreur (de casettes par ex.) ou un subwoofer. Grâce à sa petite dimension, le ESA-18 est particulièrement adapté comme système Karaoké portable mais peut également être utilisé pour la reproduction audio de votre ordinateur et comme amplificateur pour votre chaine stéréo.
E-SA18 MKBT_A6_quer_RZ_Okt.qxp_Layout 1 30.09.21 09:47 Seite 44 CONSIGNES DE SECURITE Tous les moyens d'exploitation raccordés au secteur du foyer peuvent représenter un danger pour l'utilisateur en cas d'usage non conforme. Ne pas ouvrir l'appareil! Danger de décharge électrique! Vérifiez périodiquement la sécurité technique de l’appareil.
E-SA18 MKBT_A6_quer_RZ_Okt.qxp_Layout 1 30.09.21 09:47 Seite 45 CONSIGNES DE SECURITE Le contact d'appareils électriques avec des liquides, l'humidité, la pluie ou la vapeur d'eau représente un risque pour les appareils et leurs utilisateurs et doit donc être absolument évité. Faites attention à ce qu'aucun liquide ou objet ne pénètre dans l'appareil (fentes d'aération etc.). Si cela a été le cas, il doit immédiatement être débranché du secteur et contrôlé par un spécialiste.
E-SA18 MKBT_A6_quer_RZ_Okt.qxp_Layout 1 30.09.21 09:47 Seite 46 AUTRES CONSIGNES Appareils électroniques usagés Sigle CE Cet appareil est soumis aux dispositions fixées dans la directive européenne 2012/19/EU. L'identification est fournie sur l'appareil par le symbole représentant une poubelle rayée. Tous les anciens appareils électriques ou électronique portant ce sigle qui ne sont plus utilisés doivent être séparés des ordures ménagères courantes et être éliminés dans des déchèteries spécialisées.
E-SA18 MKBT_A6_quer_RZ_Okt.qxp_Layout 1 30.09.21 09:47 Seite 47 AUTRES CONSIGNES Dynavox travaille en permanence à l'amélioration et au développement de ses produits. Pour cette raison, des modifications de design et de construction technique liées au progrès sont possibles. Le contenu de ces instructions a uniquement un caractère d'information. Il peut être modifié à tout moment sans information préalable et n'a pas valeur d'obligation pour le propriétaire de la marque.
E-SA18 MKBT_A6_quer_RZ_Okt.qxp_Layout 1 30.09.
E-SA18 MKBT_A6_quer_RZ_Okt.qxp_Layout 1 30.09.21 09:47 Seite 49 1. POWER Met l’appareil en MARCHE ou à l’ARRET, à l’ARRET, l’appareil est coupé de l’alimentation secteur. En l’état de MARCHE, la LED située à côté du commutateur reste allumée. 5. BASS Réglage des basses. 2. MIC INPUT Si vous le souhaitez, vous pouvez brancher sur cette prise Jack 6,3 mm, un microphone dynamique. En aucun cas, il n’est possible d’y brancher une source de haut niveau ! 7.
E-SA18 MKBT_A6_quer_RZ_Okt.qxp_Layout 1 30.09.
E-SA18 MKBT_A6_quer_RZ_Okt.qxp_Layout 1 30.09.21 09:47 Seite 51 11. AUDIO INPUT Vous pouvez raccorder un à deux appareils source ayant une sortie son stéréo dont les signaux sont mixés dans l’amplificateur. 14. TO SPEAKER Douilles de sortie avec serrage à vis pour le raccordement d’une ou de deux paires de haut-parleurs. On peut utiliser des câbles de haut-parleurs avec fiches banane de 4 mm. 12. PRE OUT Sur cette fiche vous pouvez raccorder un subwoofer ou un appareil enregistreur.
E-SA18 MKBT_A6_quer_RZ_Okt.qxp_Layout 1 30.09.21 09:47 Seite 52 SYSTEME KARAOKE TYPIQUE Pour un système Karaoké typique, raccordez la sortie haut niveau d’un appareil de reproduction pour la musique de fond (lecteur de CD, ordinateur, lecteur portable etc.) à l’une des entrées „AUDIO INPUT“ à l’aide d’un câble RCA ou utilisez la connexion BT. Raccordez un microphone dynamique à la douille d’entrée microphone „MIC IN“ située sur la façade de l’appareil.
E-SA18 MKBT_A6_quer_RZ_Okt.qxp_Layout 1 30.09.
E-SA18 MKBT_A6_quer_RZ_Okt.qxp_Layout 1 30.09.21 09:47 Seite 54 RACCORDEMENT ET MISE EN SERVICE ses de sorties des appareils sources sont souvent désignées par « LINE OUT ». Les prises d’entrées RCA de cet amplificateur sont des prises d’entrée de haut niveau électriquement équivalente dont le signal est mixé à l’intérieur de l’appareil. Il n’y a pas possibilité de commuter entre les deux sources RCA. Réalisez les raccordements de câbles dans l’ordre indiqué ci-après.
E-SA18 MKBT_A6_quer_RZ_Okt.qxp_Layout 1 30.09.21 09:47 Seite 55 Raccordement d’un microphone Vous pouvez brancher uniquement un microphone dynamique sur cette prise Jack 6,3 mm. Aucun autre microphone ou lecteur ne peut être branché sur cette fiche. pouvez raccorder une extrémité d’un câble de hautparleur. Sur chaque paire de bornes de serrage vous trouverez une désignation (R ou L), qui indique à quel côté (droit ou gauche) correspond la paire de bornes.
E-SA18 MKBT_A6_quer_RZ_Okt.qxp_Layout 1 30.09.21 09:47 Seite 56 RACCORDEMENT ET MISE EN SERVICE Branchement du câble d’ alimentation Branchez l’autre extrémité du cordon à une prise de courant secteur, ayant la tension appropriée (230 V/50 Hz). Ne mettez l’appareil en marche, qu’après avoir positionné le réglage de volume sonore au minimum en le tournant dans le sens anti horaire.
E-SA18 MKBT_A6_quer_RZ_Okt.qxp_Layout 1 30.09.21 09:47 Seite 57 UTILISATION DE L’APPAREIL Action Mise en marche et arrêt Touche(s) POWER (1) Description L’appareil n‘a pas de mise en veille, il est mis en marche et arrêté par le commutateur en façade avant. En position arrêt, il n‘est plus sous tension. Dans l’état de marche, la LED située à côté du commutateur secteur est allumée. Avant de mettre l’appareil en marche, prenez la précaution de réduire le réglage du volume sonore (8).
E-SA18 MKBT_A6_quer_RZ_Okt.qxp_Layout 1 30.09.21 09:47 Seite 58 UTILISATION DE L’APPAREIL Action Touche(s) Description prenez la précaution de réduire le volume (10). HIGH = Sensibilité normale, adaptée aux sources de niveau élevé LOW = Sensibilité réduite pour les signaux d’entrée de niveau plus élevé Réglage tonalité des aigus TREBLE (6) Réglage tonalité des BASS basses (5) Avec le bouton tournant de réglage „TREBLE“ de la façade de l’appareil, vous influez sur les aigus de la sonorité.
E-SA18 MKBT_A6_quer_RZ_Okt.qxp_Layout 1 30.09.21 09:47 Seite 59 Action Touche(s) Description Activer et désactiver la correction du son pour un volume sonore faible LOUDNESS (7) La fonction "Loudness" est une caractéristique de puissance des amplificateurs audio qui permet à l'utilisateur d'augmenter les fréquences basses et hautes par simple pression sur un bouton. Cette fonction ne devrait être utilisée qu’avec un volume sonore faible.
E-SA18 MKBT_A6_quer_RZ_Okt.qxp_Layout 1 30.09.21 09:47 Seite 60 UTILISATION DE L’APPAREIL Action Touche(s) Description Dice en veille automatique ON/OFF A-S ON/OFF (17) Si ce commutateur est réglé sur "I" (On), le ESA-18 MK BT s'éteint automatiquement après environ 15 minutes sans signal d'entrée. Pour désactiver cette fonction, réglez le commutateur sur la position "0" (désactivé). Pour redémarrer l'appareil il faut appuyer 2 fois sur la touche marche/arrêt.
E-SA18 MKBT_A6_quer_RZ_Okt.qxp_Layout 1 30.09.
E-SA18 MKBT_A6_quer_RZ_Okt.qxp_Layout 1 30.09.
E-SA18 MKBT_A6_quer_RZ_Okt.qxp_Layout 1 30.09.
E-SA18 MKBT_A6_quer_RZ_Okt.qxp_Layout 1 30.09.21 09:47 Seite 64 www.dynavox-audio.de Internationaler Distributor: Importeur/Importateur/Importer: Sintron Distribution GmbH · Südring 14 · D-76473 Iffezheim WEEE-Reg.Nr.