User's Manual

ManualsBrandsDynaScan Technology ManualsElectronicsDigital Transmission System

USER MANUAL

DI100ST2-M

100” Fanless UHD 4K Premium Indoor LCD

Intel® SDM Ready

65406 | V2.01

Summary of content (30 pages)

PAGE 1
DI100ST2-M USER MANUAL 100” Fanless UHD 4K Premium Indoor LCD Intel® SDM Ready 65406 | V2.
PAGE 2
Contents Material Contents Declaration ................................................................................................................ 2 Recycling and Energy Information ......................................................................................................... 2 Declaration of Conformity ....................................................................................................................... 3 Safety Precautions ..................................................
PAGE 3
Material Contents Declaration Hazardous Substances Hexavalent Polybrominated Polybromodiphenyl Part Name Lead Mercury Cadmium Chromium Biphenyls Ethers Pb Hg Cd Cr6+ PBB PBDE PCBA O O O O O O CHASSIS O O O O O O ACCESSORY O O O O O O PACKAGE O O O O O O “O” indicates that the level of the specified chemical substance is less than the threshold level specified in the standards of SJ/T-11363-2006 and EU 2011/65/EC.
PAGE 4
Declaration of Conformity FCC This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. FEDERAL COMMUNICATIONS COMMISSION INTERFERENCE STATEMENT This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part 15 of the FCC Rules.
PAGE 5
Safety Precautions CAUTION Do not install near flammable material or any heat sources. Do not defeat the safety purpose of the grounding-type plug. Do not disassemble the display to avoid electrical shock or burn. Normal operating condition considers installation at an altitude below 2000m; some abnormalities may be experienced when installed at an altitude above 2000m. WARNING Please power off the LCD and the video source before plugging in the DP or HDMI cable.
PAGE 6
Important Safety Information             Disassembling the LCD is strictly prohibited. Opening the cover may expose the user to electric shock or other hazards. Please contact DynaScan certified service professionals for all maintenance requirements. Do not allow any liquid to enter the LCD. Also avoid placing the LCD close to water sources. Do not place heavy objects on the power cord. A damaged power cord might cause electric shock or fire. Do not bend, twist, or damage the power cord.
PAGE 7
Getting Started Contents Confirm that the accessories below are shipped along with the display. If any item is missing, please contact your dealer. The color and shape of the accessories may vary with the products.       DI100ST2-M Professional LCD. Remote Control x 1 pc. Batteries (1.5V / AAA) x2 pcs. Power cable x1 pc. Quick Start Guide x1 pc. ESK302 x1 pc. Attention: Please use the following table to check whether the included power cord is suitable for your region.
PAGE 8
Installation The LCD must be properly installed using a wall mount. Incorrect installation may cause injury or damage the equipment. Product warranty does not cover the damage caused by improper installation and DynaScan shall not be held responsible in such incident. Refer to the mount manufacturer’s instructions for proper installation. Mounting    Hanging the Professional LCD from the ceiling or mounting it on the wall is the responsibility of the user.
PAGE 9
Unit: mm B A Orientation  When used in the portrait orientation, the LCD should be rotated clockwise when looking at the front of the display such that the left edge becomes the top edge.
PAGE 10
Portrait mode: Rotate the set counterclockwise 90° (mandatory)  The orientation sticker can be found on the rear of display, which is for distinguishing the direction of installation. Installation Location  The wall and mount must have enough strength to support the LCD and its accessories.  Do not install in a location with strong vibrations or dusty.  Do not install near the building’s main electric panel.
PAGE 11
Maintenance  Inspect the fasteners regularly for signs of loosening or deformation. Please perform appropriate corrective measures when a problem is identified. Neglecting the problem may worsen the situation.  Increase the inspection frequency on areas where previous maintenance had occurred to ensure the problems do not occur again. Wall Mounting     A wall mount is not included. Please purchase a VESA Standard wall mount to secure the LCD.
PAGE 12
Connecting to a Power Source Using the power cable provided, plug it in the power inlet on the side of the display shown in the diagram below. Connect the power cable to a 100-240 volt, 50 / 60Hz AC power outlet. Insert the plug completely into the socket. display and/or lead to a fire hazard. A loose power connection may cause damage to the Connecting an External Video Source Turn OFF the power of both LCD and external video device.
PAGE 13
Input / Output Terminals A. AC (IN): Connect the supplied power cord to the wall outlet. B. Power Switch: C. RJ-45 1 (IN): RJ45 network input connection. D. RJ-45 2 (IN): RJ45 network input connection. E. RS-232 (IN): RS232C network input connection for remote control from PC. F. HDMI 1 (IN): Connect the HDMI output of a PC or an AV device via a HDMI cable. G. HDMI 2 (IN): Connect the HDMI output of a PC or an AV device via a HDMI cable. H. DP (IN): I. USB 3.0 port: J.
PAGE 14
Operating Instructions Powering On/Off the Display To turn on/off the display, press the power switch on the side of the display as shown in the diagram below. ON OFF NOTE: The remote control only works when the power switch is ON.
PAGE 15
Using the Remote Control Connection using an External Sensor Kit (ESK302) Connect the ESK302 cable to the mini USB port on the side of the display, and aim the remote at the IR receiver as shown below. Meanwhile, the IR receiver on the display will be disabled. The operating range of the remote control is 2.5 meters (8 feet). NOTE: Ambient light may affect the performance of the remote control. Avoid fluorescent or neon lights in the vicinity.
PAGE 16
        *Color and shape may vary by model. ITEM         DESCRIPTION POWER MENU UP LEFT RIGHT DOWN OK BACK Power On / Off OSD On / Off Move the cursor up or change the setting of selected item. Exit the current selection. Select the highlighted item. Move the cursor down or change the setting of selected item. Enter (for DSM365 only) Return to the last page.
PAGE 17
Using the built-in keypad ITEM DESCRIPTION MENU UP DOWN LEFT RIGHT OSD On / Off, Power On / Off. Move the cursor up or change the setting of selected item. Move the cursor down or change the setting of selected item. Exit the current selection. Select the highlighted item.
PAGE 18
Navigating the On Screen Display (OSD) Menu Press the MENU button on the built-in keypad or remote control to show the OSD. Use the navigation arrows to select and adjust the menu items. *The change of each setting can only enable when you press “LEFT” (refer to p.15) to back to the last menu layer. 1. Input Source ITEM 1 ITEM 2 DEFAULT DESCRIPTION Input Source Main Failover 1 Failover 2 Failover 3 Failover 4 HDMI 1 HDMI 2 DP SDM DSM365 Command Detection OFF Set the Main input to display.
PAGE 19
ITEM 1 ITEM 2 DEFAULT Color Temperature USER 2 Red Green Blue Picture DESCRIPTION Select the color temperature. (User2, User1, D93, D65 and D55). Adjust the red light level. Range 0 – 100. Note: The feature is only supported on User2 mode. Adjust the green light level. Range 0 – 100. Note: The feature is only supported on User2 mode. Adjust the blue light level. Range 0 – 100. Note: The feature is only supported on User2 mode. Adjust the contrast level. Range 0 – 100. Adjusts the Gamma value.
PAGE 20
4. Backlight ITEM 1 ITEM 2 DEFAULT DESCRIPTION If the AUTO BRIGHTNESS is “Off”, the screen brightness will remain at HIGH LEVEL brightness value. B. If the AUTO BRIGHTNESS is “Auto”, the brightness of display will be adjusted according to the ambient light. When ambient light is bright, the screen will adjust to the High Level brightness value set; when ambient light is dark, the screen will adjust to the Low Level brightness value set. C.
PAGE 21
5. Advance ITEM 1 ITEM 2 DEFAULT Display Mode Auto Screen Protection Off IR Control On Power Off Mode Stand By AC Back Status Power On Volume 50 Reset Default Setting Off Advance DESCRIPTION Change the Menu orientation. The Menu can be displayed in either LANDSCAPE or PORTRAIT mode. Turn on / off image burn-in protection. Set image burn-in protection interval. Range 0 – 100 minutes. Enable/disable the remote control for Menu.
PAGE 22
6. Information ITEM 1 Information ITEM 2 DEFAULT DESCRIPTION Resolution Input resolution. MCB Version The H/W version. FW Version The F/W version. Cabinet Temp. ETK Temp. Humidity LCD inner (backlight unit) temperature monitoring. The Extension Thermal Kit (ETK203) is for ambient temperature monitoring. LCD inner (backlight unit) humidity monitoring. Some functions may not be available for all models.
PAGE 23
Specifications MODEL PANEL POWER MECHANICAL SPECS USER INTERFACE ENVIRONMENT I/O Ports Fuse DI100ST2-M LCD Panel Size Native Resolution Brightness Contrast Ratio Response Time Viewing Angle Life Time Panel Surface Power Supply Rated Voltage Power On Mode (Typ./ Max) Bezel Width (T/B/L/R) Cabinet Color Monitor Dimension (LxHxD) Monitor Weight Orientation 99.5 inches 3840 x 2160 700 cd/m² (Typ.) 3,000:1 6.5 ms (Typ.) 178°/ 178° 50,000 hrs (Typ.) AGLR, 3H Internal 100 - 240V, 50 / 60Hz 500W 20.9/20.
PAGE 24
Input Mode Active Resolution H Pixels V Lines 640 720 800 960 1024 1280 1280 1280 1280 1366 1400 1440 1600 1680 1920 1920 1920 1920 2560 3840 480 480 600 600 768 720 768 960 1024 768 1050 900 1200 1050 720 1080 1200 1440 1440 2160 Refresh Rate 60 Hz 60 Hz 60 Hz 60 Hz 60 Hz 60 Hz 60 Hz 60 Hz 60 Hz 60 Hz 60 Hz 60 Hz 60 Hz 60 Hz 60 Hz 60 Hz 60 Hz 60 Hz 60 Hz 60 Hz DI100ST2-M User Manual 23
PAGE 25
Pin Assignments RS-232 Input PIN No.
PAGE 26
Troubleshooting ISSUE RECOMMENDED SOLUTION   No image is displayed. Nothing happens when switching the main switch on.    Check whether the cable is completely plugged in. Check whether the main switch is in the ON position, and the power cord is completely plugged in. Check whether the image source’s resolution is set as the supported format (refer to section “Input Mode”, p.23). Check whether the cable is damaged or bent excessively.
PAGE 27
About DSM365 DSM365 is an internal operating system as Android, which can install the applications via USB flash drive storage, SD card or Internet. How to Switch to DSM365   Press the MENU button on either the rear panel control or remote control to show the OSD. Use the navigation arrows to select and adjust the Input Source. [Input Source Main DSM365]  ITEM  DESCRIPTION APPS Show the Installed APPS.
PAGE 28
About SDM Install SDM on the display 1. Loosen screws and remove the SDM cover from the display. 2. Insert the SDM module into the display and fasten screws. Make sure the SDM properly installed to avoid causing the devise destruction.
PAGE 29
Switch to SDM   Press the MENU button on either the rear panel control or remote control to show the OSD. Use the navigation arrows to select and adjust the Input Source.