User's Manual

ManualsBrandsDynaScan Technology ManualsElectronicsDigital Transmission System

USER MANUAL

DW651LR5

65” Clean Back Digital Signage

66502 | V2.03

Summary of content (33 pages)

PAGE 1
DW651LR5 USER MANUAL 65” Clean Back Digital Signage 66502 | V2.
PAGE 2
Contents Material Contents Declaration ................................................................................................................ 2 Recycling and Energy Information ......................................................................................................... 2 Declaration of Conformity ....................................................................................................................... 3 Safety Precautions ..................................................
PAGE 3
Material Contents Declaration Hazardous Substances Hexavalent Polybrominated Polybromodiphenyl Part Name Lead Mercury Cadmium Chromium Biphenyls Ethers Pb Hg Cd Cr6+ PBB PBDE PCBA O O O O O O CHASSIS O O O O O O ACCESSORY O O O O O O PACKAGE O O O O O O “O” indicates that the level of the specified chemical substance is less than the threshold level specified in the standards of SJ/T-11363-2006 and EU 2011/65/EC.
PAGE 4
Declaration of Conformity FCC This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. FEDERAL COMMUNICATIONS COMMISSION INTERFERENCE STATEMENT This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part 15 of the FCC Rules.
PAGE 5
Déclaration de conformité FCC Cet appareil est conforme à la section 15 de la réglementation FCC. Son utilisation est sujette aux deux conditions suivantes : (1) cet appareil ne doit pas causer d'interférence nuisible, et (2) cet appareil doit accepter toute interférence reçue, y compris celles qui peuvent causer un fonctionnement non souhaité.
PAGE 6
Safety Precautions CAUTION Do not install near flammable material or any heat sources. Do not defeat the safety purpose of the grounding-type plug. Do not disassemble the display to avoid electrical shock or burn. Normal operating condition considers installation at an altitude below 2000m; some abnormalities may be experienced when installed at an altitude above 2000m. WARNING Please power off the LCD and the video source before plugging in the DP or HDMI cable.
PAGE 7
Précautions relatives à la sécurité PRÉ CAUTIONS N'installez pas installer à proximité de matériaux inflammables ou de sources de chaleur. Ne pas compromettre la sécurité de la fiche de mise à la terre. Pour éviter tout choc électrique ou la brûlure, ne démontez pas l'écran. Le produit peut normalement être utilisé à une altitude inférieure à 2000 m. Des anomalies peuvent survenir lors de l’installation de l’appareil à une altitude supérieure à 2000 m.
PAGE 8
Important Safety Information             Disassembling the LCD is strictly prohibited. Opening the cover may expose the user to electric shock or other hazards. Please contact DynaScan certified service professionals for all maintenance requirements. Do not allow any liquid to enter the LCD. Also avoid placing the LCD close to water sources. Do not place heavy objects on the power cord. A damaged power cord might cause electric shock or fire. Do not bend, twist, or damage the power cord.
PAGE 9
Informations importantes relatives à la sécurité             Le démontage de l'écran LCD est strictement interdit. L'ouverture du capot peut exposer l'utilisateur à un choc électrique ou à d'autres dangers. Veuillez contacter des professionnels de service certifiés DynaScan pour tous les besoins de maintenance. Ne laissez aucun liquide pénétrer dans l'écran LCD. Évitez également de placer l’écran LCD à proximité de sources d’eau. Ne placez aucun objet lourd sur le cordon d'alimentation.
PAGE 10
Getting Started Contents Confirm that the accessories below are shipped along with the display. If any item is missing, please contact your dealer. The color and shape of the accessories may vary with the products.       DW651LR5 Professional LCD. Remote Control x 1 pc. Batteries (1.5V / AAA) x2 pcs. Power cable x1 pc. Quick Start Guide x1 pc. ESK302 x1 pc. (optional kit) Attention: Please use the following table to check whether the included power cord is suitable for your region.
PAGE 11
Bien débuter Contenu Vérifiez que les accessoires ci-dessous sont fournis avec l’écran. Si l'un d'eux est manquant, veuillez contacter immédiatement votre revendeur. La couleur et la forme des accessoires peuvent varier selon les produits.       É cran LCD DW651LR5 Professional.
PAGE 12
Installation The LCD has been designed with two ways installation, which suitable for (1) Stand and (2) Ceiling Mount applications. Please note that the display must be properly installed onto the stand (DynaScan optional kit) or well-connected with the hanging kit (DynaScan optional kit), details please refer to the display installation guide. Incorrect installation may cause injury or damage the equipment.
PAGE 13
(2) Ceiling Mount Model Screw Location Landscape Screw Length Number M6 10mm is required 4 1310.2 DW651LR5 Portrait Screw Specification 629.
PAGE 14
Orientation  Take off the cover on the rear of display and the orientation sticker can be found inside, which is for distinguishing the direction of installation. Installation Location  Do not install in a location with strong vibrations or dusty.  Do not install near the building’s main electric panel.  Ensure the LCD is secured in such a manner that it cannot be easily removed by the general public.  Leave clearance around the outer edge of the LCD from other objects to ensure proper ventilation.
PAGE 15
Connecting to a Power Source Take off the cover from the back of display. Using the power cable provided, plug it in the power inlet which shown in the diagram below. Connect the power cable to a 100-240 volt, 50 / 60Hz AC power outlet. Insert the plug completely into the socket. display and/or lead to a fire hazard. A loose power connection may cause damage to the Connecting an External Video Source Turn OFF the power of both LCD and external video device. Take off the cover from the back of display.
PAGE 16
Input / Output Terminals A. RJ-45 1 (IN): RJ45 network input connection. B. RJ-45 2 (IN): RJ45 network input connection. C. RS-232 (IN): RS232C network input connection for remote control from PC. D. HDMI 1 (IN): Connect the HDMI output of a PC or an AV device via a HDMI cable. E. HDMI 2 (IN): Connect the HDMI output of a PC or an AV device via a HDMI cable. F. DP (IN): G. USB 3.0 port: H. Extension Connector: I. Micro SD card: J. Thermal: K. Audio (OUT): L. AC (IN): M.
PAGE 17
Operating Instructions Powering On/Off the Display To turn on/off the display, take off the cover from the back of display first. as shown in the diagram below. Press the power switch on ON OFF NOTE: The remote control only works when the power switch is ON.
PAGE 18
Using the Remote Control Connection using an External Sensor Kit (ESK302) Take off the cover from the back of display. Connect the ESK302 cable (optional kit) to the mini USB port, and aim the remote at the IR receiver as shown below. Meanwhile, the IR receiver on the display will be disabled. NOTE: Ambient light may affect the performance of the remote control. Avoid fluorescent or neon lights in the vicinity.
PAGE 19
        *Color and shape may vary by model. ITEM         DESCRIPTION POWER MENU UP LEFT RIGHT DOWN OK BACK Power On / Off OSD On / Off Move the cursor up or change the setting of selected item. Exit the current selection. Select the highlighted item. Move the cursor down or change the setting of selected item. Enter (for DSM365 only) Return to the last page.
PAGE 20
Using the built-in keypad ITEM DESCRIPTION MENU UP DOWN LEFT RIGHT OSD On / Off, Power On / Off. Move the cursor up or change the setting of selected item. Move the cursor down or change the setting of selected item. Exit the current selection. Select the highlighted item.
PAGE 21
Navigating the On Screen Display (OSD) Menu Press the MENU button on the built-in keypad or remote control to show the OSD. Use the navigation arrows to select and adjust the menu items. *The change of each setting can only enable when you press “LEFT” (refer to p.14) to back to the last menu layer. 1. Input Source ITEM 1 ITEM 2 DEFAULT DESCRIPTION Input Source Main Failover 1 Failover 2 Failover 3 Failover 4 HDMI 1 HDMI 2 DP DSM365 SDM Set the Main input to display.
PAGE 22
Green Blue Adjust the green light level. Range 0 – 100. Note: The feature is only supported on User2 mode. Adjust the blue light level. Range 0 – 100. Note: The feature is only supported on User2 mode. Adjust the contrast level. Range 0 – 100. Adjusts the Gamma value. (Native, 2.2, 2.4 and sGamma) Selects the black level to adjust the screen gray scale. "Limited" for video source uses 16 to 235 levels for R/G/B, such as HDMI. "RGB Full" for video source uses all levels from 0 to 255 levels.
PAGE 23
4. Backlight ITEM 1 ITEM 2 DEFAULT DESCRIPTION If the AUTO BRIGHTNESS is “Off”, the screen brightness will remain at HIGH LEVEL brightness value. B. If the AUTO BRIGHTNESS is “Auto”, the brightness of display will be adjusted according to the ambient light. When ambient light is bright, the screen will adjust to the High Level brightness value set; when ambient light is dark, the screen will adjust to the Low Level brightness value set. C.
PAGE 24
5. Advance ITEM 1 ITEM 2 DEFAULT Display Mode Portrait Screen Protection Off IR Control On Power Off Mode Standby AC Back Status Power On Volume 50 Reset Default Setting Off Advance DESCRIPTION Change the Menu orientation. The Menu can be displayed in either LANDSCAPE, PORTRAIT or PORTRAIT FLIP mode. Turn on / off image burn-in protection. Set image burn-in protection interval. Range 0 – 100 minutes. Enable/disable the remote control for Menu.
PAGE 25
6. Information ITEM 1 ITEM 2 DEFAULT Resolution Model Information DESCRIPTION Input resolution. DW651LR5 The display’s model. Serial Number The display’s serial number. Hardware The H/W version. Firmware The F/W version. Cabinet Temp. ETK Temp. Humidity ALS Level LCD inner (backlight unit) temperature monitoring. The Extension Thermal Kit (ETK203) is for ambient temperature monitoring. LCD inner (backlight unit) humidity monitoring. The brightness of ambience monitoring.
PAGE 26
Specifications MODEL PANEL POWER MECHANICAL SPECS USER INTERFACE ENVIRONMENT I/O Ports Fuse DW651LR5 LCD Panel Size Native Resolution Brightness Contrast Ratio Response Time Viewing Angle Life Time Panel Surface Power Supply Rated Voltage Power On Mode Power Saving Mode Bezel Width (T/B/L/R) Cabinet Color Monitor Dimension (LxHxD) Monitor Weight (set / package) Orientation OSD Language 64.53 inches 3840 x 2160 4000 cd/m² (Typ.) 3,000:1 8 ms (Typ.) 178°/ 178° 100,000 hrs (Typ.
PAGE 27
Input Mode Active Resolution H Pixels V Lines 640 720 800 960 1024 1280 1280 1280 1280 1366 1400 1440 1600 1680 1920 1920 1920 1920 2560 3840 480 480 600 600 768 720 768 960 1024 768 1050 900 1200 1050 720 1080 1200 1440 1440 2160 Refresh Rate 60 Hz 60 Hz 60 Hz 60 Hz 60 Hz 60 Hz 60 Hz 60 Hz 60 Hz 60 Hz 60 Hz 60 Hz 60 Hz 60 Hz 60 Hz 60 Hz 60 Hz 60 Hz 60 Hz 60 Hz 26
PAGE 28
Pin Assignments RS-232 Input PIN No.
PAGE 29
Troubleshooting ISSUE RECOMMENDED SOLUTION   No image is displayed. Nothing happens when switching the main switch on.    Check whether the cable is completely plugged in. Check whether the main switch is in the ON position, and the power cord is completely plugged in. Check whether the image source’s resolution is set as the supported format (refer to section “Input Mode”, p.22). Check whether the cable is damaged or bent excessively.
PAGE 30
About DSM365 DSM365 is an internal operating system as Android, which can install the applications via USB flash drive storage, SD card or Internet. How to Switch to DSM365   Press the MENU button on either the rear panel control or remote control to show the OSD. Use the navigation arrows to select and adjust the Input Source. [Input Source Main DSM365]  ITEM  DESCRIPTION APPS Show the Installed APPS.
PAGE 31
About SDM Install SDM on the display 1. Loosen screws and remove the SDM cover from the display. 2. Insert the SDM module into the display and fasten screws. Make sure the SDM properly installed to avoid causing the devise destruction.
PAGE 32
Switch to SDM   Press the MENU button on either the rear panel control or remote control to show the OSD. Use the navigation arrows to select and adjust the Input Source.