User's Manual

ManualsBrandsDynaScan Technology ManualsElectronicsDigital Transmission System

User Manual

65701

Model Code: DI881LT2

Version 2.01

The use of diagrams and illustrations in the manual are for reference only. The actual product may be different.

Product design and specifications are subject to change without notice

Summary of content (27 pages)

PAGE 1
User Manual 65701 Model Code: DI881LT2 Version 2.01 The use of diagrams and illustrations in the manual are for reference only. The actual product may be different.
PAGE 2
Contents Material Contents Declaration ........................................................................................................... 2 Recycling and Energy Information..................................................................................................... 2 Declaration of Conformity.................................................................................................................. 3 Safety Precautions...................................................................
PAGE 3
Material Contents Declaration Hazardous Substances Hexavalent Polybrominated Polybromodiphenyl Part Name Lead Mercury Cadmium Biphenyls Ethers Chromium Pb Hg Cd Cr6+ PBB PBDE PCBA O O O O O O CHASSIS O O O O O O ACCESSORY O O O O O O PACKAGE O O O O O O “O” indicates that the level of the specified chemical substance is less than the threshold level specified in the standards of SJ/T-11363-2006 and 2011/65/EU.
PAGE 4
Declaration of Conformity FCC This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. FEDERAL COMMUNICATIONS COMMISSION INTERFERENCE STATEMENT This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules.
PAGE 5
Safety Precautions CAUTION Do not install near flammable material or any heat sources. Do not defeat the safety purpose of the grounding-type plug. Do not disassemble the display to avoid electrical shock or burn. Normal operating condition considers installation at an altitude below 2000m; some abnormalities may be experienced when installed at an altitude above 2000m. WARNING Please power off the LCD and the video source before plugging in the DP or HDMI cable.
PAGE 6
Important Safety Information • • • • • • • • • • • • Disassembling the LCD is strictly prohibited. Opening the cover may expose the user to electric shock or other hazards. Please contact DynaScan certified service professionals for all maintenance requirements. Do not allow any liquid to enter the LCD. Also avoid placing the LCD close to water sources. Do not place heavy objects on the power cord. A damaged power cord might cause electric shock or fire. Do not bend, twist, or damage the power cord.
PAGE 7
Getting Started Contents Confirm that the accessories below are shipped along with the display. If any item is missing, please contact your dealer. The color and shape of the accessories may vary with the products. • • • 65701 Professional LCD. Remote Control x 1 pc. Batteries (1.5V / AAA) x2 pcs. • • • Power cable x1 pc. Quick Start Guide x1 pc. ESK302 x1 pc. Attention: Please use the following table to check whether the included power cord is suitable for your region.
PAGE 8
Installation The LCD must be properly installed using a wall mount. Incorrect installation may cause injury or damage the equipment. Product warranty does not cover the damage caused by improper installation and DynaScan shall not be held responsible in such incident. Refer to the mount manufacturer’s instructions for proper installation. Mounting • • • • We recommend for at least four people to handle and mount the display. Mounting the Professional LCD on the wall is the responsibility of the user.
PAGE 9
Unit: mm B A Orientation • When used in the portrait orientation, the LCD should be rotated clockwise when looking at the front of the display such that the left edge becomes the top edge. Portrait mode: Rotate the set clockwise 90° (mandatory) • The orientation sticker can be found on the rear of display, which is for distinguishing the direction of installation.
PAGE 10
Installation Location • The wall and mount must have enough strength to support the LCD and its accessories. • Do not install in a location with strong vibrations or dusty. • Do not install near the building’s main electric panel. • Ensure the LCD is secured in such a manner that it cannot be easily removed by the general public. • Leave clearance around the outer edge of the LCD (or video wall matrix) from other objects to ensure proper ventilation.
PAGE 11
Wall Mounting • • • • A wall mount is not included. Please purchase a VESA Standard wall mount to secure the LCD. DynaScan is not responsible for damages caused by using non-standard wall mounts. Verify that the mounting location can support the weight of the LCD before installation. The installation angle must be within 15 degrees of the vertical axis. Do not install the wall mount while the power is turned on as it may cause serious injury from electrical shock.
PAGE 12
Connecting an External Video Source Turn OFF the power of both LCD and external video device. Using the DP cable (or HDMI cable) provided, insert one end into the DP-IN (or HDMI 1-IN, HDMI 2-IN) on the back of the display shown the in the diagram below. Connect the other end of the DP cable (HDMI cable) to the DP output (or HDMI output) of the video source. Refer to your video device’s manual for additional information.
PAGE 13
Input / Output Terminals A. B. C. D. E. USB port: Support for USB flash drive storage, mouse and keyboard. SD card: Support for up to 32GB, FAT32/NTFS format is supported. RJ-45 (IN): RJ45 network input connection. HDMI 1 (IN): Connect the HDMI output of a PC or an AV device via a HDMI cable. HDMI 2 (IN): Connect the HDMI output of a PC or an AV device via a HDMI cable. F. G. H. I. J. K. L. M. N. DP (IN): Connect the DP output of a PC or an AV device via a DP cable.
PAGE 14
Operating Instructions Powering On/Off the Display To turn on/off the display, press the power switch on the back of the display as shown in the diagram below. ON OFF NOTE: The remote control only works when the power switch is ON.
PAGE 15
Using the Remote Control • The operating range of the remote control is 2.5 meters (8 feet). • Ambient light may affect the performance of the remote control. Avoid fluorescent or neon lights in the vicinity. Connect the ESK302 cable to the sensor port (mini USB port) on the back of the display. When using the remote control, aim the remote at the IR receiver on the ESK302.
PAGE 16
*Color and shape may vary by model. ITEM DESCRIPTION POWER MENU UP LEFT RIGHT DOWN OK BACK Power On / Off OSD On / Off Move the cursor up or change the setting of selected item. Exit the current selection. Select the highlighted item. Move the cursor down or change the setting of selected item. Enter (for DSM365 only) Return to the last page.
PAGE 17
Using the built-in keypad ITEM DESCRIPTION MENU UP DOWN LEFT RIGHT OSD On / Off, Power On / Off. Move the cursor up or change the setting of selected item. Move the cursor down or change the setting of selected item. Exit the current selection. Select the highlighted item.
PAGE 18
Navigating the On Screen Display (OSD) Menu Press the MENU button on the built-in keypad or remote control to show the OSD. Use the navigation arrows to select and adjust the menu items. *The change of each setting can only enable when you press “LEFT” (refer to p.15) to back to the last menu layer. 1. Input Source ITEM 1 ITEM 2 DEFAULT DESCRIPTION Input Source Main Failover 1 Failover 2 Failover 3 HDMI 1 DP HDMI 2 DSM365 Set the Main input to display. Set the Failover 1 input to display.
PAGE 19
16 to 235 levels for R/G/B, such as HDMI. "RGB Full" for video source uses all levels from 0 to 255 levels. 3. Time ITEM 1 Time ITEM 2 DEFAULT DESCRIPTION Current Date YYYY:MM:DD Current Time HH:MM:SS Day of Week Daylight Saving Power Control Timer Power On Time Power Off Time Off Set the date. Set the clock. Note: The internal clock will continue to function when the power is turned off. Set the day of week. (Monday to Sunday) Turn on / off DST setting.
PAGE 20
High Level 100 Low Level 20 High Level Time Low Level Time 08:00 18:00 Local Dimming Medium ITEM 2 DEFAULT Display Mode Landscape Screen Protection Off IR Control On Volume 100 Reset to Default Setting Off AC Back Status Power On display will automatically switch the brightness according to the time set. Adjusts the highest brightness level. Range 0 – 100. Adjusts the lowest brightness level. Range 0 – 100. Set high level time. Set low level time. Adjusts the contrast.
PAGE 21
6. Information ITEM 1 ITEM 2 Resolution Model Serial Number Hardware Software Temperature (BLU) DEFAULT DI881LT2 Temperature (Amb.) Information ALS Level Over Heat Protection Inactive Running Time DESCRIPTION Input resolution. The display’s model. The display’s serial number. The H/W version. The F/W version. LCD inner (backlight unit) temperature monitoring. LCD outer (ambience) temperature monitoring. (temperature sensor installation is necessary) The brightness of ambience monitoring.
PAGE 22
Specifications MODEL NAME 65701 MODEL CODE DI881LT2 PANEL POWER MECHANICAL SPECS USER INTERFACE ENVIRONMENT I/O Ports Fuse LCD Panel Size Native Resolution Brightness Contrast Ratio Response Time Viewing Angle Life Time Panel Surface Power Supply Rated Voltage Power On Mode Bezel Width (T/B/L/R) Cabinet Color Monitor Dimension (LxHxD) Monitor Weight (set / package) VESA Mounting (Dimension) OSD Language 88 inches 3840 x 1080 1,000 cd/m² (Typ.) 3,000:1 8 ms (Typ.) 178°/ 178° 50,000 hrs (Typ.
PAGE 23
Input Mode Active Resolution H Pixels V Lines 640 800 1024 1280 1280 1280 1280 1366 1440 1600 1920 1920 2560 2560 3840 480 600 768 768 800 960 1024 768 900 1200 1080 1200 1440 1600 2160 Refresh Rate 60 Hz 60 Hz 60 Hz 60 Hz 60 Hz 60 Hz 60 Hz 60 Hz 60 Hz 60 Hz 60 Hz 60 Hz 60 Hz 60 Hz 60 Hz 65701 User Manual 22
PAGE 24
Pin Assignments RS-232 Output PIN No. 01 02 03 04 05 06 07 08 09 NAME Connected to 7&8 RXD TXD Connected to 6 GND Connected to 4 Connected to 1&8 Connected to 1&7 NC RS-232 Input PIN No.
PAGE 25
Troubleshooting ISSUE RECOMMENDED SOLUTION No image is displayed. Check whether the signal cable is completely plugged in. Check whether the main switch is in the ON position, and the power cord is completely plugged in. Check whether the image source’s resolution is set as the supported format (refer to section “Input Mode”, p.22). Check whether the cable is damaged or bent excessively. Check content inputs are working fine. Nothing happens when switching the main switch on.
PAGE 26
About DSM365 DSM365 is an internal operating system as Android, which can install the applications via USB flash drive storage, SD card or Internet. How to Switch to DSM365 • • Press the MENU button on either the rear panel control or remote control to show the OSD. Use the navigation arrows to select and adjust the Input Source. [Input Source→ Main→ DSM365] ITEM DESCRIPTION APPS SETTINGS Show the Installed APPS. Enter the setting menu.