User's Manual

ManualsBrandsDynaScan Technology ManualsElectronicsDigital Transmission Systems

USER MANUAL

DS552LT5-2

55” Fanless High Brightness Digital Signage Display

64428 | V2.00

Summary of content (32 pages)

PAGE 1
DS552LT5-2 USER MANUAL 55” Fanless High Brightness Digital Signage Display 64428 | V2.
PAGE 2
Contents Material Contents Declaration ................................................................................................................ 1 Recycling and Energy Information ......................................................................................................... 1 Declaration of Conformity ....................................................................................................................... 2 Déclaration de conformité............................................
PAGE 3
Material Contents Declaration Hazardous Substances Hexavalent Polybrominated Polybromodiphenyl Part Name Lead Mercury Cadmium Chromium Biphenyls Ethers Pb Hg Cd Cr6+ PBB PBDE PCBA O O O O O O CHASSIS O O O O O O ACCESSORY O O O O O O PACKAGE O O O O O O “O” indicates that the level of the specified chemical substance is less than the threshold level specified in the standards of SJ/T-11363-2006 and EU 2005/618/EC.
PAGE 4
Declaration of Conformity FCC This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. FEDERAL COMMUNICATIONS COMMISSION INTERFERENCE STATEMENT This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part 15 of the FCC Rules.
PAGE 5
Déclaration de conformité FCC Cet appareil est conforme à la section 15 de la réglementation FCC. Son utilisation est sujette aux deux conditions suivantes : (1) cet appareil ne doit pas causer d'interférence nuisible, et (2) cet appareil doit accepter toute interférence reçue, y compris celles qui peuvent causer un fonctionnement non souhaité.
PAGE 6
Safety Precautions CAUTION Do not install near flammable material or any heat sources. Do not defeat the safety purpose of the grounding-type plug. Do not disassemble the display to avoid electrical shock or burn. Normal operating condition considers installation at an altitude below 2000m; some abnormalities may be experienced when installed at an altitude above 2000m. WARNING Please power off the LCD and the video source before plugging in the DP or HDMI cable.
PAGE 7
Précautions relatives à la sécurité PRÉ CAUTIONS N'installez pas installer à proximité de matériaux inflammables ou de sources de chaleur. Ne pas compromettre la sécurité de la fiche de mise à la terre. Pour éviter tout choc électrique ou la brûlure, ne démontez pas l'écran. Le produit peut normalement être utilisé à une altitude inférieure à 2000 m. Des anomalies peuvent survenir lors de l’installation de l’appareil à une altitude supérieure à 2000 m.
PAGE 8
Important Safety Information             Disassembling the LCD is strictly prohibited. Opening the cover may expose the user to electric shock or other hazards. Please contact DynaScan certified service professionals for all maintenance requirements. Do not allow any liquid to enter the LCD. Also avoid placing the LCD close to water sources. Do not place heavy objects on the power cord. A damaged power cord might cause electric shock or fire. Do not bend, twist, or damage the power cord.
PAGE 9
Informations importantes relatives à la sécurité             Le démontage de l'écran LCD est strictement interdit. L'ouverture du capot peut exposer l'utilisateur à un choc électrique ou à d'autres dangers. Veuillez contacter des professionnels de service certifiés DynaScan pour tous les besoins de maintenance. Ne laissez aucun liquide pénétrer dans l'écran LCD. Évitez également de placer l’écran LCD à proximité de sources d’eau. Ne placez aucun objet lourd sur le cordon d'alimentation.
PAGE 10
Getting Started Contents Confirm that the accessories below are shipped along with the display. If any item is missing, please contact your dealer. The color and shape of the accessories may vary with the products.       DS552LT5-2 Professional LCD. Remote Control x 1 pc. Batteries (1.5V / AAA) x2 pcs. Power cable x1 pc. Quick Start Guide x1 pc. ESK302 x1 pc. Attention: Please use the following table to check whether the included power cord is suitable for your region.
PAGE 11
Bien débuter Contenu Vérifiez que les accessoires ci-dessous sont fournis avec l’écran. Si l'un d'eux est manquant, veuillez contacter immédiatement votre revendeur. La couleur et la forme des accessoires peuvent varier selon les produits.    É cran LCD DS552LT5-2 Professional.
PAGE 12
Installation The LCD must be properly installed using a wall mount. Incorrect installation may cause injury or damage the equipment. Product warranty does not cover the damage caused by improper installation and DynaScan shall not be held responsible in such incident. Refer to the mount manufacturer’s instructions for proper installation. Mounting     We recommend for at least four people to handle and mount the display. Mounting the Professional LCD on the wall is the responsibility of the user.
PAGE 13
Unit: mm B A Orientation  When used in the portrait orientation, the LCD should be rotated clockwise when looking at the front of the display such that the left edge becomes the top edge. Portrait mode: Rotate the set clockwise 90° (mandatory)  The orientation sticker can be found on the rear of display, which is for distinguishing the direction of installation.
PAGE 14
Installation Location  The wall and mount must have enough strength to support the LCD and its accessories.  Do not install in a location with strong vibrations or dusty.  Do not install near the building’s main electric panel.  Ensure the LCD is secured in such a manner that it cannot be easily removed by the general public.  Leave clearance around the outer edge of the LCD (or video wall matrix) from other objects to ensure proper ventilation.
PAGE 15
Wall Mounting     A wall mount is not included. Please purchase a VESA Standard wall mount to secure the LCD. DynaScan is not responsible for damages caused by using non-standard wall mounts. Verify that the mounting location can support the weight of the LCD before installation. The installation angle must be within 15 degrees of the vertical axis. Do not install the wall mount while the power is turned on as it may cause serious injury from electrical shock.
PAGE 16
Connecting an External Video Source Turn OFF the power of both LCD and external video device. Using the DP cable (or HDMI cable) provided, insert one end into the DP-IN (or HDMI 1-IN, HDMI 2-IN) on the back of the display shown the in the diagram below. Connect the other end of the DP cable (HDMI cable) to the DP output (or HDMI output) of the video source. Refer to your video device’s manual for additional information.
PAGE 17
Input / Output Terminals A. AC (IN): Connect the supplied power cord to the wall outlet. B. Power Switch: C. Audio (OUT): D. RJ-45 1 (IN): RJ45 network input connection. E. HDMI 1 (IN): Connect the HDMI output of a PC or an AV device via a HDMI cable. F. HDMI 2 (IN): Connect the HDMI output of a PC or an AV device via a HDMI cable. G. RS-232 (IN): RS232C network input connection for remote control from PC. H. USB 2.0 port 1: Support for USB flash drive storage, mouse and keyboard. I.
PAGE 18
Operating Instructions Powering On/Off the Display To turn on/off the display, press the power switch on the back of the display as shown in the diagram below. ON OFF NOTE: The remote control only works when the power switch is ON.
PAGE 19
Using the Remote Control Connection using an External Sensor Kit (ESK302) Connect the ESK302 cable to the mini USB port on the side of the display, and aim the remote at the IR receiver as shown below. Meanwhile, the IR receiver on the display will be disabled. The operating range of the remote control is 2.5 meters (8 feet). NOTE: Ambient light may affect the performance of the remote control. Avoid fluorescent or neon lights in the vicinity.
PAGE 20
        *Color and shape may vary by model. ITEM         DESCRIPTION POWER MENU UP LEFT RIGHT DOWN OK BACK Power On / Off OSD On / Off Move the cursor up or change the setting of selected item. Exit the current selection. Select the highlighted item. Move the cursor down or change the setting of selected item. Enter (for DSM365 only) Return to the last page.
PAGE 21
Using the built-in keypad ITEM DESCRIPTION MENU UP DOWN LEFT RIGHT OSD On / Off, Power On / Off. Move the cursor up or change the setting of selected item. Move the cursor down or change the setting of selected item. Exit the current selection. Select the highlighted item.
PAGE 22
Navigating the On Screen Display (OSD) Menu Press the MENU button on the built-in keypad or remote control to show the OSD. Use the navigation arrows to select and adjust the menu items. *The change of each setting can only enable when you press “LEFT” (refer to p.19) to back to the last menu layer. 1. Input Source ITEM 1 ITEM 2 DEFAULT DESCRIPTION Main Failover 1 Failover 2 HDMI 1 HDMI 2 DSM365 Command Detection Off Set the Main input to display. Set the Failover 1 input to display.
PAGE 23
ITEM 1 ITEM 2 DEFAULT Color Temperature USER 2 Red Green Blue Picture Contrast 60 Gamma Native Black Level Limited ITEM 2 DEFAULT DESCRIPTION Select the color temperature. (User2, User1, D93, D65 and D55). Adjust the red light level. Range 0 – 100. Note: The feature is only supported on User2 mode. Adjust the green light level. Range 0 – 100. Note: The feature is only supported on User2 mode. Adjust the blue light level. Range 0 – 100. Note: The feature is only supported on User2 mode.
PAGE 24
High Level 100 Low Level 7 High Level Time Low Level Time 08:00 18:00 Local Dimming High ITEM 2 DEFAULT display will automatically switch the brightness according to the time set. D. When setting “Mix” mode, Timer and Light sensor will work at this mode. For example, setting "High Level Time = 8:00am" and "Low Level Time = 6:00pm", the light sensor will detect environment brightness and then display will adjust the value of High Level during 8:00am and 6:00pm. Adjusts the highest brightness level.
PAGE 25
5. Advance ITEM 1 Advance ITEM 2 DEFAULT Display Mode Auto Screen Protection OFF IR Control ON Power Off Mode Standby AC Back Status Power On Audio Out Volume 50 Source Info ON DESCRIPTION Change the Menu orientation. The Menu can be displayed in either LANDSCAPE or PORTRAIT mode. Turn on / off image burn-in protection. Set image burn-in protection interval. Range 0 – 100 minutes. Enable/disable the remote control for Menu.
PAGE 26
RS232 CMD Compatible ON OSD Password Protection OFF RS232 Command compatible between the new and old model. Turn On: Create Password > Confirm Password > Password Protection On Turn Off: Enter Password > Password Protection Off Reset OSD Password Enter Password > Enter New Password > Confirm New Password > Success Export & Import Settings Export or Import OSD Setting by USB. Reset Default Setting Restore all settings to default.
PAGE 27
Specifications MODEL PANEL POWER MECHANICAL SPECS USER INTERFACE ENVIRONMENT I/O Ports Fuse DS552LT5-2 LCD Panel Size Native Resolution Brightness Contrast Ratio Response Time Viewing Angle Life Time Panel Surface Power Supply Rated Voltage Power On Mode Standby Mode Bezel Width (T/B/L/R) Cabinet Color Monitor Dimension (LxHxD) Monitor Weight (set / package) VESA Mounting (Dimension) 54.64 inches 1920 x 1080 4,000 cd/m² (Typ.) 3,000:1 9 ms (Typ.) 178°/ 178° 100,000 hrs (Typ.
PAGE 28
Input Mode Active Resolution H Pixels V Lines 640 720 800 960 1024 1280 1280 1280 1280 1366 1400 1440 1600 1680 1920 1920 480 480 600 600 768 720 768 960 1024 768 1050 900 1200 1050 720 1080 Refresh Rate 60 Hz 60 Hz 60 Hz 60 Hz 60 Hz 60 Hz 60 Hz 60 Hz 60 Hz 60 Hz 60 Hz 60 Hz 60 Hz 60 Hz 60 Hz 60 Hz DS552LT5-2 User Manual 26
PAGE 29
Pin Assignments RS-232 Input PIN No.
PAGE 30
Troubleshooting ISSUE RECOMMENDED SOLUTION   No image is displayed. Nothing happens when switching the main switch on.    Check whether the cable is completely plugged in. Check whether the main switch is in the ON position, and the power cord is completely plugged in. Check whether the image source’s resolution is set as the supported format (refer to section “Input Mode”, p.27). Check whether the cable is damaged or bent excessively.
PAGE 31
About DSM365 DSM365 is an internal operating system as Android, which can install the applications via USB flash drive storage, SD card or Internet. How to Switch to DSM365   Press the MENU button on either the rear panel control or remote control to show the OSD. Use the navigation arrows to select and adjust the Input Source. [Input Source → Main → DSM365]  ITEM  DESCRIPTION APPS Show the Installed APPS.