User's Manual Part 2

ManualsBrandsDYE PRECISION ManualsElectronicsM2

WWW.DYEPAINTBALL.COM

ADJUSTING YOUR REACH

TRIGGER

The trigger’s travel and reach

angle are fully adjustable so that

you can fine-tune the trigger

to your preference. You do not

need to remove the frame or grip

from the gun in order to make an

adjustment to the trigger.

There are two adjustment

screws located on the left side

of the Ultralite frame and one

adjustment screw behind the

trigger. The two screws on the

side of the frame adjust the travel

of the trigger.

The one located behind the

trigger will adjust the magnet’s

strength.

TO ADJUST TRIGGER TRAVEL

Use a 5⁄6 4” Allen wrench to make the desired adjustments.

• The bottom screw (1) controls the forward travel. Screwing it in will shorten the trigger’s

length of pull.

NOTE: IF THIS SCREW IS ADJUSTED TOO FAR, THE SWITCH WILL BE HELD

DOWN AT ALL TIMES AND THE MARKER WILL NOT FIRE.

• The top screw (2) controls the over travel. By turning this screw you can adjust how

far the trigger will travel after it reaches the firing point.

NOTE: IF THIS SCREW IS ADJUSTED TOO FAR, THE TRIGGER WILL NOT BE

ALLOWED TO TRAVEL FAR ENOUGH TO DEPRESS THE SWITCH AND FIRE THE

MARKER.

TO ADJUST MAGNET STRENGTH

• Use a 5⁄6 4” Allen wrench to make the desired adjustment. Insert the Allen wrench

through the hole behind the trigger blade (3).

• To make the trigger pull stronger, turn the Allen wrench clockwise or in.

• To make the trigger pull weaker, turn the Allen wrench counterclockwise or out.

ULTRALITE REACH TRIGGER

The M2 has an external reach angle adjustment for the Ultralite trigger.

This adjustment changes the angle that the trigger blade sits without affecting the trigger

activation point.

TO ADJUST TRIGGER REACH

To adjust, simply loosen the two 6-32 screws (4) using a 1/16” Allen wrench. You do not

have to remove the screws from the trigger. Now the front of the trigger should rotate freely

while the back of the trigger remains relatively stationary. When the desired trigger angle

has been achieved, tighten the two 6-32 screws snugly. Be careful not to over tighten and

strip the Allen wrench or screws.

REACH TRIGGER ADJUSTMENT

BE SURE THE TRIGGER IS NOT ADJUSTED TO THE POINT

WHERE IT IS TOO SENSITIVE AND MAY CAUSE ACCIDENTAL

DISCHARGE OF THE MARKER.

Summary of content (18 pages)

PAGE 1
REACh TRIGGER ADJUSTMENT ADJUSTING YOUR REACh TRIGGER The trigger’s travel and reach angle are fully adjustable so that you can fine-tune the trigger to your preference. You do not need to remove the frame or grip from the gun in order to make an adjustment to the trigger. There are two adjustment screws located on the left side of the Ultralite frame and one adjustment screw behind the trigger. The two screws on the side of the frame adjust the travel of the trigger.
PAGE 2
STICkY GRIP REMOvAL 1. Pull the upper back corner of the grips away from the gripframe with your thumb. Allowing the rear tab to clear the frame. 2. While pulling with your thumb, use your index finger, to push the grips toward you. 3. The top portion of the grips should now be free from the gripframe. 5. Pull the grip forward and down. 6. In doing so, you will have released the last three locking tabs that are under the molded finger grooves. 7.
PAGE 3
FUSE™ BOLT ASSEMBLY AND MAINTENANCE 2 1 3 FUSE™ BOLT OPERATION To achieve top performance from your M2, it is important to understand the basic operation of the M2’s patented FUSE™ bolt system. This design consists of three sleeves threaded together to capture the only moving part of the system, the bolt. The FUSE™ Bolt has six components: 1 2 3 4 5 6 BACK POSITION Cylinder Bolt Sail Bolt Top Hat Manifold Tool-less Back Cap W . D Y E P A I N to the rear of the cylinder.
PAGE 4
FUSE™ BOLT ASSEMBLY AND MAINTENANCE BOLT MAINTENANCE Regular Fuse™ bolt maintenance is vital to the performance of the M2. If the Fuse™ bolt is not kept well greased and the O-rings in good shape, the performance of the M2 will be greatly hindered. 7 7 7 7 7 The M2 software tracks how many shots the marker has fired, and will alert you when service is due. A red service icon will flash over the playing screen. See service system on page 8 for more info.
PAGE 5
hYPER5™ GAS ThRU REGULATOR BASIC vELOCITY ADJUSTMENT ADJUSTMENTS The Hyper5 regulator controls your velocity. It is pre-set at approximately 140 psi. This will enable your gun to shoot about 285 FPS. The M2’s velocity will be affected by paint size, weather conditions, altitude and other factors. To adjust your velocity use a 3/16” Allen wrench and insert it into the bottom of the fore grip where the Hyper5 reg is located.
PAGE 6
hYPER5™ GAS ThRU REGULATOR The M2 software tracks how many shots the marker has fired, and will alert you when service is due. A red service icon will flash over the playing screen. See service system on page 8 for more info. NOTE: IT IS IMPORTANT TO kEEP ThE SEAT AND PISTON FACE CLEAN OF ALL DIRT AND DEBRIS. CLEAN ThE SEAT AND PISTON FACE AND APPLY FRESh GREASE EvERY 6 MONThS OR 75,000 - 100,000 ShOTS, DEPENDING ON PLAYING CONDITIONS.
PAGE 7
LPR (LOW PRESSURE REGULATOR) ADJUSTMENTS AND MAINTENANCE LPR ASSEMBLY, CLEANING, TESTING AND ChANGING SEALS The Low-Pressure Regulator (LPR) is located at the front of the M2 under the barrel. The function of the LPR is to lower the air pressure supplied to the marker by the Hyper5™ before it reaches the solenoid. This air pressure is used to cycle the bolt forward and back. LPR ADJUSTMENT The LPR is pre-set at approximately 65 PSI. Generally there is no reason to adjust the Factory LPR setting.
PAGE 8
LPR (LOW PRESSURE REGULATOR) ADJUSTMENTS AND MAINTENANCE LPR DISASSEMBLY INSTRUCTIONS The LPR is housed in a self-contained cartridge. A fouled LPR cartridge can be quickly removed for service. The only user-serviceable part in the LPR is the regulator Seat, located in the Seat Retainer. This seal needs to be changed in the unlikely case the LPR is allowing gas through the regulator, increasing pressure sent to the solenoid. The M2 is equipped with an internal digital pressure sensor for the LPR.
PAGE 9
ShiftPort ASA ShiftPort ASA The M2 comes equipped with a the ShiftPort ASA attached to the bottom of the frame. To turn on the gas supply, rotate the side lever counter clockwise until the internal stop is reached. To turn off the gas supply, rotate the side lever clockwise until the other stop is reached. As you rotate the side lever past the mid point, the residual gas between the Hyper5™ and the ShiftPort ASA will vent. ShiftPort ASA LENGTH ADJUSTMENT The ShiftPort can be adjusted for optimal comfort.
PAGE 10
ULTRALITE FRAME & LOCk DOWN MICRO FEED NECk LOCk DOWN MICRO FEED NECk The Lock Down Micro Feedneck is adjustable to fit any standard loader. To adjust the cam locking system, lift the cam lever away from the feed collar, and rotate the lever clockwise to tighten or counterclockwise to loosen the grip on the loader. Once the cam lever is facing in the forward direction, press the cam lever down against the feed collar to secure the loader in the feedneck.
PAGE 11
EYE PIPE ANTI ChOP EYES/ BALL DETENTS ANTI ChOP EYES The Anti Chop Eye (ACE) system will help prevent the M2 from chopping paint by preventing the marker from firing until a ball is fully seated in front of the bolt. The eyes use a light beam across the breech. In order for the marker to fire with the eyes turned on, the signal between the two eyes must be broken (a paintball in the breach). After every shot, before the next ball drops in the breech, the eye transmitter and receiver must see each other.
PAGE 12
Trouble Shooting Guide AIR LEAKS Air leaking from the BACK OF airport • Check the O-ring on the Air system. If needed change the O-ring and try again. The O-ring normally used is 015 but some manufacturers might use a different size. Consult the manual of the air system you are using. Air leaking between Frame & airport • Make sure airport locking screw is tight Air leaking from the Hyper5™ regulator • First locate the position of the leak.
PAGE 13
TROUBLE SHOOTING GUIDE SOLENOID WILL NOT ACTIVATE / TRIGGER NOT WORKING • Check that the trigger adjustment is not set so that the micro switch cannot activate. You should hear a small click when pulling the trigger. VELOCITY IS NOT CONSISTENT • your trigger is set so that the micro switch is always activated. Re-adjust the trigger. • Check that the solenoid cable is attached to the board and to the correct connector (solenoid should be attached to the two-prong connector).
PAGE 14
27
PAGE 15
EXPLODED VIEW 1 2 3 8 PARTS LIST 5 9 1 Clamping Micro Feed Neck 6 2 Ball Detent Clip 3 Eye Pipe 4 4 Eye Seal 13 5 M2 Body 21 12 7 11 6 FUSE™ Bolt 7 Tool-less Back Cap 8 LPR Retainer Nut 20 10 9 LPR Cartridge 10 Solenoid 14 11 Sensor Board 15 12 Eye Wire 13 Hyper5™ 19 14 Front Frame Mounting Screw 15 Rear Frame Mounting Screw 16 16 Ultralite Frame 17 17 MOS AIR Board 18 18 ShiftPort ASA 19 Sticky Grip 20 Transfer Board 22 21 Reach Trigger 22 Regulator Sleeve W W W .
PAGE 16
M2 Warranty and legal information WARRANTY DYE Precision, Inc. warrants for one year to the initial retail purchaser, from the initial date of purchase, that the paintball marker and regulator are free from defects in materials and workmanship, subject to the requirements, disclaimers and limitations of this warranty. Disposable parts, normal maintenance and standard wear and tear parts such as batteries, O-rings and seals are not warrantied.
PAGE 17
QUICK START PAGE The e.VOKE Air Sync system includes: • e.VOKE i5 Air Sync smart box • Micro USB charging cable • M2 Air Sync transmitter board with M2 x 3 mm screw • User’s manual The e.VOKE system is compatible with the M2 MOSAir board. POWER ON To power on your e.VOKE press and hold the center button for 2 seconds. To power off hold center button for 3 seconds. CHARGING Use a standard mini USB cable to charge your e.VOKE from any power supply. During charging the Power level is indicated by the LED.
PAGE 18
BUTTON CHART 3 (rear) 2 (center) 1 (front) BUTTON Button #1 front SINGLE CLICK Add to G-count PRESS/HOLD Reset G-count Button #2 center Game times updates POWER : HOLD 2 SEC = ON, HOLD 3 SEC = OFF Button #3 rear #1 and #3 #1 and #2 Shot tracker update Motivations HOLD #2, TAP #1 = Volume + Search for device for pairing #3 and #2 HOLD #2, TAP #3 = Volume - FEATURES: FEATURES: FUTURE PROGRAMING: UPDATE FIRMWARE: AIR SYNC: The e.