Installation Sheet

ManualsBrandsDXV ManualsBathroom FaucetsPercy Ws Lever Handle 1.2 GPM

- 1 -

INSTALLATION INSTRUCTIONS

Product names listed herein are trademarks of AS America, Inc.

SAVE FOR FUTURE USE

RECOMMENDED TOOLS AND MATERIALS

Most of the procedures require the use of common tools and materials, which are available from hardware and plumbing,

supply stores. It is essential that the tools and materials be on hand before work is begun.

M965710 Rev. 1.0 (5/17)

Cross Handle

Model D3510584C

Lever Handle

Model D3510580C

Percy

Widespread Faucet

ROUGHING-IN DIMENSIONS:

• For reference

Plumbers' Putty or CaulkingAdjustable Wrench

Phillips Screwdriver

Channel Locks Flat Blade Screwdriver

6" to 12"

(152 to 305 mm)

9-11/16"

(245 mm)

6-9/16"

(167 mm)

5-7/16"

(138 mm)

MOUNTING

SURFACE

2-1/4"

(57 mm)

2-1/4" DIA.

(57 mm)

7/8" DIA.

(22 mm)

1-1/2" MAX.

(38 mm)

CROSS

HANDLE

10-1/2" MAX.

(267 mm)

1-1/4" O.D.

(32 mm)

2" MAX

(51 mm)

1-1/2"

(37 mm)

LEVER

HANDLE

2-1/2"

(63 mm)

NOTE: MOUNTING HOLES ARE 1-3/8" DIA. (35 mm)

CONNECTIONS:

• 1/2" IPS FLEXIBLE SUPPLIES

• 3/8" O.D. BULL-NOSE RISERS

In the United States:

DXV

One Centennial Avenue

Piscataway, New Jersey 08855

Attention: Director of Customer Care

For residents of the United States, warranty

information may also be obtained by calling

the following toll free number: (800) 227-2734

www.DXV.com

In Canada:

DXV

5900 Avebury Road

Mississauga, Ontario

L5R 3M3

Canada

Toll Free: 1-800-387-0369

Local: 905-306-1093

Fax: 1-800-395-1498

www.DXV.ca

In Mexico:

DXV

Via Morelos 330

Col. Santa Clara Coatitla

Ecatepec, Estado de México 55540

Toll Free: 01-800-8391200

www.DXV.mx

Thank you for selecting DXV. To ensure that your

installation proceeds smoothly, please read these

instructions carefully before you begin.

Summary of content (8 pages)

PAGE 1
INSTALLATION INSTRUCTIONS Percy® Widespread Faucet Cross Handle Model D3510584C Lever Handle Model D3510580C Thank you for selecting DXV. To ensure that your installation proceeds smoothly, please read these instructions carefully before you begin. RECOMMENDED TOOLS AND MATERIALS Most of the procedures require the use of common tools and materials, which are available from hardware and plumbing, supply stores. It is essential that the tools and materials be on hand before work is begun.
PAGE 2
1 SPOUT ASSEMBLY CAUTION 2 TEE ASSEMBLY Turn off hot and cold water supplies before beginning. • Thread TEE BODY (1) COUPLING NUT (2) to SPOUT SHANK (3). Tighten with wrenches. • Insert SPOUT ASSEMBLY (1) and CABLE CONNECTOR (2) through center hole, making sure O-RING SEAL (3) is properly seated in SPOUT BASE (4) groove. • Assemble RUBBER WASHER (5), BRASS WASHER (6) and LOCKNUT (7) onto SPOUT SHANK (8) from under side of sink.
PAGE 3
4 INSTALL POP-UP DRAIN Fig. B. Fig. A. 1 • Remove CLEAR PLASTIC COVER (1). Fig. A. • Remove FOAM SPACER (2) from under DRAIN POP-UP (3). Fig. A. DRAIN BODY 3 • Tighten TAILPIECE (4) on DRAIN BODY before installing DRAIN BODY. Fig. B. 4 2 5 REMOVE MOUNTING WASHERS Fig. A. AND LOCKNUT Fig. B. REAR OF SINK • Thread LOCKNUT (1) counter-clockwise and remove from drain body. Remove PLASTIC WASHER (2) and pull off RUBBER CONE WASHER (3). Fig. A. 3 • Drop DRAIN BODY (4) through sink drain hole.
PAGE 4
9 ATTACH CABLE CONNECTOR Fig. B. Fig.A. A. Fig. • Thread CABLE CONNECTOR (1) clockwise onto DRAIN BODY CONNECTION (2) and hand tighten. Fig. A. 1 Your new POP-UP DRAIN installation is now complete. Fig. B. Note: Tailpeice on pop-up drain is 1-1/4" O.D. (32mm) Fig. B. 2 1-1/4" O.D. (32mm) 10 CHECK OPERATION OF POP-UP • Operate LIFT KNOB (1) to verify that STOPPER (2) opens and closes.
PAGE 5
12 CONNECT DRAIN • Connect 1-1/4" (32mm) O.D. tailpiece on POP-UP DRAIN to waste outlet. 1-1/4" (32mm) O.D. TAILPIECE WASTE OUTLET 13 TEST INSTALLED FITTING • With HANDLE (1) in OFF position, turn on WATER SUPPLIES (2) and check all connections for leaks. • Remove AERATOR (3). Loosen AERATOR HOUSING (4) and remove AERATOR (3). 3 4 • Operate HANDLES (1) to flush water lines thoroughly. • Replace AERATOR (3) and tighten AERATOR HOUSING (4).
PAGE 6
Speed Connect® Drain Troubleshooting Guide If sink does not hold water even though Stopper is in the “down” position: • Follow CABLE ADJUSTMENT PROCEDURE. If Stopper does not raise up fully or sink drains too slowly: • Follow CABLE ADJUSTMENT PROCEDURE. If you need to remove the Stopper: • Follow STOPPER REMOVAL PROCEDURE. If you would like the ability to remove your Stopper simply by lifting it out of the drain: • Follow STOPPER INSTALLATION PROCEDURE for “Unlocked” mode.
PAGE 7
STOPPER INSTALLATION PROCEDURE The Stopper can be installed two ways, “Locked” Mode (Stopper cannot be removed) or “Unlock” Mode (Stopper is removable). Fig. G. LOCKED MODE: • Look at the Plastic Loop at the bottom of the Stopper and notice that the Loop is on one side of the Stopper. Fig. G. • To install the stopper in “Locked” mode, insert the Stopper into the Drain so that the Plastic Loop is facing toward the rear of the Sink.
PAGE 8
Percy® Widespread Faucet MODEL NUMBERS Cross Handle D3510584C Lever Handle D3510580C Replace the “YYY” with appropriate finish code M964630-YYY0A LEVER HANDLE ASSEMBLEY POLISHED CHROME 100 BRUSHED NICKEL 144 M964629-YYY0A CROSS HANDLE ASSEMBLEY M964751-YYY0A LIFT KNOB ASSEMBLY M952430-0070A SPEED CONNECT CABLE ASSEMBLY M964752-YYY0A AERATOR ASSEMBLY M964712-0070A O-RING H960295.191 SPOUT MTG. KIT H960279.191 MOUNTING KIT M953006-0070A TEE & HOSE ASSEMBLY H960136.