Installation Sheet

ManualsBrandsDXV ManualsBathroom FaucetsRandall 1.2 GPM Widespread Bathroom Faucet with Pop-Up Drain Assembly

- 1 -

INSTALLATION INSTRUCTIONS

Product names listed herein are trademarks of AS America, Inc.

SAVE FOR FUTURE USE

RECOMMENDED TOOLS AND MATERIALS

Most of the procedures require the use of common tools and materials, which are available from hardware and plumbing

supply stores. It is essential that the tools and materials be on hand before work is begun.

M965705 Rev. 1.1 (2/17)

Cross Handle

Model D3510284C

Lever Handle

Model D3510280C

Randall

Widespread Lavatory Faucet

ROUGHING-IN DIMENSIONS:

• For reference

1-3/8"

(35 mm)

5-3/8"

(136 mm)

2-3/8" DIA.

(61 mm)

LEVER

HANDLE

CROSS

HANDLE

1-1/4" MAX.

(32 mm)

1-1/16" DIA.

(29 mm)

3-3/4"

(96 mm)

3-3/4"

(96 mm)

6" - 12"

(153 - 305 mm)

(76 mm)

7/8" DIA.

(22 mm)

1-1/4 O.D.

(32 mm)

8-1/16" MAX.

(205 mm)

MAX 2"

(51 mm)

NOTE: MOUNTING HOLES ARE 1-3/8" DIA. (35 mm)

CONNECTIONS:

• 1/2" IPS FLEXIBLE SUPPLIES

• 3/8" O.D. BULL-NOSE RISERS

Plumbers' Putty or Caulking

Phillips Screwdriver

Channel LocksTubing Cutter Flat Blade Screwdriver Adjustable Wrench

Basin Wrench

In the United States:

DXV

One Centennial Avenue

Piscataway, New Jersey 08855

Attention: Director of Customer Care

For residents of the United States, warranty

information may also be obtained by calling

the following toll free number: (800) 227-2734

www.DXV.com

In Canada:

DXV

5900 Avebury Road

Mississauga, Ontario

L5R 3M3

Canada

Toll Free: 1-800-387-0369

Local: 905-306-1093

Fax: 1-800-395-1498

www.DXV.ca

In Mexico:

DXV

Via Morelos 330

Col. Santa Clara Coatitla

Ecatepec, Estado de México 55540

Toll Free: 01-800-8391200

www.DXV.mx

Thank you for selecting DXV. To ensure that your

installation proceeds smoothly, please read these

instructions carefully before you begin.

Summary of content (8 pages)

PAGE 1
INSTALLATION INSTRUCTIONS Randall® Widespread Lavatory Faucet Cross Handle Model D3510284C Lever Handle Model D3510280C Most of the procedures require the use of common tools and materials, which are available from hardware and plumbing supply stores. It is essential that the tools and materials be on hand before work is begun.
PAGE 2
1 SPOUT ASSEMBLY CAUTION 2 TEE ASSEMBLY Turn off hot and cold water supplies before beginning. • Thread TEE BODY (1) COUPLING NUT (2) to SPOUT SHANK (3). • Insert SPOUT (1) and CABLE CONNECTOR (2) through center hole, making sure SEAL WASHER (3) is properly seated in SPOUT BASE (4) groove. 1 4 • Assemble RUBBER GROOVE WASHER (5), BRASS WASHER (6) and LOCKNUT (7) 3 onto SPOUT SHANK (8) from under side of sink.
PAGE 3
4 POP-UP DRAIN Fig. A. Fig. B. • Remove CLEAR PLASTIC COVER (1). Fig. A. 1 • Remove CARDBOARD SPACER (2) from under DRAIN POP-UP (3). Fig. A. 3 DRAIN BODY • Tighten TAILPIECE (4) on DRAIN BODY before installing DRAIN BODY. Fig. B. 2 5 REMOVE FLANGE 4 Fig. A. • Thread FLANGE (1) counter-clockwise and remove FLANGE (1) and FOAM GASKET (2) from drain body. Fig. A. Fig. B. 1 • Thread LOCKNUT (3) clock-wise to bottom of drain body. Push GASKET (4) down against LOCKNUT (3). Fig. B.
PAGE 4
9 ATTACH CABLE CONNECTOR Fig. A. Fig. B. • Thread CABLE CONNECTOR (1) clockwise onto DRAIN BODY CONNECTION (2) and hand tighten. Fig. A. 1 • Your new POP-UP DRAIN installation is now complete. Fig. B. Note: Tailpeice on pop-up drain is 1-1/4" (32 mm) O.D. Fig. B. 2 1-1/4” O.D. 10 CHECK OPERATION OF POP-UP 1 • Operate LIFT KNOB (1) to verify that STOPPER (2) opens and closes.
PAGE 5
12 CONNECT DRAIN • Connect 1-1/4" (32 mm) O.D. tailpiece on POP-UP DRAIN to waste outlet. WASTE OUTLET 1-1/4" (32 mm) O.D. TAILPIECE 13 TEST INSTALLED FITTING 1 5 • With HANDLES (1) in OFF position, turn on WATER SUPPLIES (2) and check all connections for leaks. • Remove AERATOR (3). • Operate both HANDLES (1) to flush water lines thoroughly. • Replace AERATOR (3). 1 3 4 14 CHECK DRAIN CONNECTIONS • Operate POP-UP KNOB (5) and fill Sink with water.
PAGE 6
Speed Connect® Drain Troubleshooting Guide If sink does not hold water even though Stopper is in the “down” position: • Follow CABLE ADJUSTMENT PROCEDURE. If Stopper does not raise up fully or sink drains too slowly: • Follow CABLE ADJUSTMENT PROCEDURE. If you need to remove the Stopper: • Follow STOPPER REMOVAL PROCEDURE. If you would like the ability to remove your Stopper simply by lifting it out of the drain: • Follow STOPPER INSTALLATION PROCEDURE for “Unlocked” mode.
PAGE 7
STOPPER INSTALLATION PROCEDURE The Stopper can be installed two ways, “Locked” Mode (Stopper cannot be removed) or “Unlock” Mode (Stopper is removable). LOCKED MODE: • Look at the Plastic Loop at the bottom of the Stopper and notice that the Loop is on one side of the Stopper. Fig. G. Fig. G. • To install the stopper in “Locked” mode, insert the Stopper into the Drain so that the Plastic Loop is facing toward the rear of the Sink.
PAGE 8
Randall® Widespread Lavatory Faucet MODEL NUMBERS Cross Handle D3510284C Replace the “YYY” with appropriate finish code Lever Handle POLISHED CHROME 100 BRUSHED NICKEL 144 PLATINUM NICKEL 150 SATIN BRASS 427 D3510280C A860682.XXX HANDLE CAP H960622.XXX POP-UP KNOB M964764-YYY0A POP-UP ROD A860682.XXX HANDLE CAP A860680.XXX CROSS HANDLE SET A860681.XXX LEVER HANDLE SET H960625.XXX ROSETTE & WASHER M964737-YYY0A AERATOR ASSEMBLY H960295.191 SPOUT MOUNTING KIT H960628.