Important Please read this User’s Manual carefully to familiarize yourself with safe and effective usage. Please retain this manual for future reference.
For U.S.A. , Canada, etc. (rated 100-120 Vac) Only FCC Declaration of Conformity We, the Responsible Party EIZO NANAO TECHNOLOGIES INC. 5710 Warland Drive, Cypress, CA 90630 Phone: (562) 431-5011 declare that the product Trade name: EIZO Model: DuraVision FDX1001T/FDV1001T/FDX1201T is in conformity with Part 15 of the FCC Rules.
SAFETY SYMBOLS This manual and this product use the safety symbols below. They denote critical information. Please read them carefully. WARNING Failure to abide by the information in a WARNING may result in serious injury and can be life threatening. CAUTION Failure to abide by the information in a CAUTION may result in moderate injury and/or property or product damage. Indicates an attention to be required. For example, the symbol risk of electric shock”. Indicates a prohibited action.
PRECAUTIONS IMPORTANT • To ensure personal safety and proper maintenance, please read this section and the caution statements on the unit (refer to the figure below). 【Location of Caution Statement】 WARNING If the unit begins to emit smoke, smells like something is burning, or makes strange noises,disconnect all power connections immediately and contact your dealer for advice. Attempting to use a malfunctioning unit may result in fire, electric shock, or equipment damage.
WARNING Use the unit in an appropriate location. Not doing so may result in fire, electric shock, or equipment damage. • Do not place outdoors. • Do not place in a transportation system (ship, aircraft, train, automobile, etc.) where it may be affected by strong vibration or shock. • Do not place in a dusty or humid environment. • Do not place in a location where water is splashed on the screen (bathroom, kitchen, etc.). • Do not place in a location where the steam comes directly on the screen.
WARNING Do not touch a damaged LCD panel directly with bare hands. The liquid crystal that may leak from the panel is poisonous if it enters the eyes or mouth. If any part of the skin or body comes in direct contact with the panel, please wash thoroughly. If some physical symptoms result, please consult your doctor. CAUTION Handle with care when carrying the unit. Disconnect the power cord and cables when moving the unit. Moving the unit with the cord attached is dangerous. It may result in injury.
Notice for this monitor Aside from displaying microscope images, this product is also suited to the dedicated usages such as operation of terminal equipment. This product has been adjusted specifically for use in the region to which it was originally shipped. If the product is used outside the region, it may not operate as specified in the specifications. This product may not be covered by warranty for uses other than those described in this manual.
Cleaning ATTENTION • Never use any solvents or chemicals, such as thinner, benzene, wax, alcohol, and abrasive cleaner, which may damage the cabinet or panel. • Do not soak liquid into the clearance between the panel and the panel frame. NOTE • Optional ScreenCleaner is recommended for cleaning the panel surface. ● Panel • Clean the panel with a soft cloth such as cotton cloth or lens cleaning paper.
CONTENTS Cover ............................................................. 1 PRECAUTIONS................................................. 3 Notice for this monitor............................................... 6 CONTENTS ............................................................. 8 Chapter 1 Introduction........................................ 9 1-1. Features............................................................... 9 1-2. Package Contents............................................... 9 1-3.
Chapter 1 Introduction Thank you very much for choosing an EIZO color LCD monitor. 1-1. Features • FDX1001T/FDV1001T: 10.4-inch screen, FDX1201T: 12.
1-3. Controls and Functions 12 Setting menu 13 1 1 button 2 button 3 4 2 3 4 5 6 7 8 9 11 Switches the input signal. button button Displays the Setting menu, fixes the setting or adjustment items on each menu, and saves the setting or adjustment results. ・Used to select the setting or adjustment items, or to increase or decrease the adjustment values on each menu. or switches ・When the settings menu is not displayed, pressing between displaying and not displaying the crosshair.
Chapter 2 Connecting Cables 2-1. Connection Procedures 1 Connects to external equipment compatible with the monitor.
(1) Connect the monitor to the PC with a signal cable that matches the connectors. After connecting the cable connectors, tighten the screws of the connectors to secure the coupling. monitor PC D-Sub mini 15-pin connector Signal cable MD-C87 (optional) D-Sub mini 15-pin connector or Signal cable FD-C16 (optional) DVI connector ● When using video equipment (1) Connect the monitor to the video equipment with a signal cable that matches the connectors.
2 Plug the power cord of the monitor into a power outlet. (1) Connect the power cord to the AC adapter. (2) Connect the AC adapter to the Power jack of the monitor, and after that, connect the power plug to a power outlet. ATTENTION • This product does not include a power cord. Please provide separately a power cord which meets the usage requirements. • For the maximum power saving, it is recommended that the Power button be turned off.
2-3.Installing the Touch Panel Driver ATTENTION • The user account to be used for installing the touch panel driver must have the “Administrators” privilege. • When reinstalling the touch panel driver to update the driver, etc., restart the PC after uninstalling the driver and then install it. 1 2 Uninstall the other touch panel driver, if it is installed. Install the touch panel driver according to the instructions included in the CDROM.
Chapter 3 Settings and Adjustments 3-1. Basic Operation and Functions Basic operation of Setting menu 1 Displaying Setting Menu Press . 2 Setting/Adjusting 3 Exiting Choose [Exit] with or , and press . NOTE • Keeping pressed for 2 seconds will also exit the Setting menu.
Functions The settings adjustable in the Setting menu are as shown below. The availability of items depends on the input signal.
3-2. Color Adjustment This will perform color adjustments. Please switch between the input screens you want to adjust and adjust them one by one. Adjustable item / adjustable value Adjusting Brightness 0 - 30 Adjusts the brightness of the backlight. Contrast 0 - 30 Adjusts the contrast. Black Level 0 - 30 Adjusts the image brightness. Sharpness Off/Low/High Adjusts the image outlines. Saturation -30 - +30 Adjusts the saturation. Hue -30 - +30 Adjusts the hue.
3-3. Configure other settings This will configure other settings. Setting item / setting value Setting Video Aspect Configures the display range of the input image (overscan). Normal/100% “Normal” : Displays the input image with the outmost parts slightly cut off. * This is how display devices normally display images. “100%” : Displays most of the input image.
Chapter 4 Troubleshooting If a problem still remains after applying the suggested remedies, contact your local dealer. Common Problems Possible cause and remedy No picture • Power indicator does not light. • Check whether the power cord is connected correctly. • If the problem persists, turn off the power, and then turn it on again a few minutes later. • Power indicator lights orange. • Press • Power indicator lights blue. • Check whether the power of the connected device is turned on.
Touch panel problems 20 Problems Possible cause and remedy Cursor position is not correct. / Cursor jumps. • Turn off and on the monitor. If the symptom is not improved, perform the calibration on the monitor. • Touch with one finger only. • Connect the monitor to the PC with the cable indicated in the User’s Manual of the monitor. Using a conversion adapter, the touch panel may not operate properly. Touch operation is not effective.
Chapter 5 Reference 5-1. Attaching an Arm The stand can be removed and replaced with an arm (or another stand) to be attached to the monitor. Use an arm or stand of EIZO option. ATTENTION • When attaching an arm or stand, follow the instructions of their user’s manual. • When using another manufacturer’s arm or stand, confirm the following in advance and select one conforming to the VESA standard. Use the M4 × 12 mm screws in use by this monitor.
5-2. Specifications FDX1001T LCD Panel Size 10.4-inch (260 mm) TFT color LCD Surface treatment Anti-glare Surface hardness 2H Viewing angle Horizontal 160°, Vertical 130° (CR : 10 or more) Dot Pitch 0.2055 mm Display Area (H × V) 210.4 mm × 157.8 mm Resolution 1024 dots × 768 lines Max. Display Color Approx. 16.7 million colors PC input Horizontal Scan Frequency 24-50 kHz Vertical Scan Frequency 55-75 Hz (Non-interlace) Max.
Environmental Temperature Conditions [Operating temperature] Main unit : 0 °C - 50 °C (32 °F - 122 °F) AC adapter : 0 °C - 40 °C (32 °F - 104 °F) [Storage temperature] -20 °C - 60 °C (-4 °F - 140 °F) Humidity [Operating humidity] Main unit : 20% - 90% R.H. (wet bulb temperature ≤ 39 °C (102 °F), no condensation) AC adapter : 20% - 85% R.H.(no condensation) [Storage humidity] 10% - 90% R.H.
Dimensions (Width) × (Height) × (Depth) Main unit 252 mm (9.9 inch) × 255 mm (10 inch) × 175 mm (6.9 inch) Main unit (without stand) 252 mm (9.9 inch) × 216 mm (8.5 inch) × 45 mm (1.77 inch) Mass Main unit Approx. 3.7 kg (8.2 lbs.) Main unit (without stand) Approx. 2.1 kg (4.6 lbs.
Video input Applicable Format NTSC, PAL, SECAM Input Signal Connector S-Video DIN mini 4 pin/ Video Pin jack × 1 Input Signal Level S-Video DIN mini 4 pin : Y 1.0Vp-p/75Ω, C 0.28Vp-p/75Ω Video Pin jack : 1.0Vp-p/75Ω Power Supply Power Consumption AC adapter (AC) : 100-240VAC±10%, 50/60Hz, 0.4-0.25A (Max.) Main unit (DC) : 12VDC±10%, 1.4 A Screen Display On AC adapter (AC) : 20 W or less Main unit (DC) : 17 W or less Power Off AC adapter (AC) : 1.6 W or less Main unit (DC) : 0.
Outside Dimensions unit : mm (inch) 45 (1.77) 21 (0.83) FDX1001T / FDV1001T 30° 20 (0.79) 36 (1.42) 93 (3.66) 291 (11.5) 252 (9.9) 213 (8.4) 160 (6.3) 216 (8.5) 255 (10.0) 20 (0.79) 20 (0.79) 35° 35° 175 (6.9) 201 (7.9) 200 (7.9) 22 (0.87) 200 (7.9) 30° 84 (3.31) 34.8 (1.37) 186 (7.3) 244 (9.6) 271 (10.7) 247.4 (9.7) 22.8 (0.90) 306 (12.0) 293 (11.5) 22.8 (0.90) 23.2 (0.91) 35° 35° 46 (1.81) FDX1201T 175 (6.9) 207 (8.
Connector Pin Assignment • D-Sub mini 15-pin connector 3 4 5 1 2 8 9 10 7 6 14 13 12 11 15 Pin No. Signal 1 Red video Pin No. 6 Signal Red video ground Pin No. 11 Signal NC* 2 Green video 7 Green video ground 12 Data (SDA) 3 Blue video 8 Blue video ground 13 H. Sync 4 NC* 9 NC* 14 V. Sync 5 Ground 10 Ground 15 Clock (SCL) (NC*: No Connection) • Serial port for the touch panel 3 2 1 6 7 5 4 8 9 Pin No. Signal Pin No.
5-3. Glossary Afterimage The Afterimage is particular to LCD monitors. When the monitor screen is left on for a long period without use. The Afterimage can be removed gradually by changing the displayed image. Clock The analog input monitor needs to reproduce a clock of the same frequency as the dot clock of the graphics system in use, when the analog input signal is converted to a digital signal for image display. This is called clock adjustment.
5-4. Preset Timing The following table shows the factory preset video timing of the PC. ATTENTION • Display position may be deviated depending on the PC connected, which may require screen adjustment using Setting menu. • If a signal other than those listed in the table is input, adjust the screen using the Setting menu. However, screen display may still be incorrect even after the adjustment.
LIMITED WARRANTY EIZO NANAO CORPORATION (hereinafter referred to as “EIZO”) and distributors authorized by EIZO (hereinafter referred to as the “Distributors”) warrant, subject to and in accordance with the terms of this limited warranty (hereinafter referred to as the “Warranty”), to the original purchaser (hereinafter referred to as the “Original Purchaser”) who purchased the product specified in this document (hereinafter referred to as the “Product”) from EIZO or Distributors, that EIZO and Distributors
关于电子信息产品污染控制标识 本标识根据「电子信息产品污染控制管理办法」，适用于在中华人民共和国销售的电子信息产品。标识中央的 数字为环保使用期限的年数。只要您遵守该产品相关的安全及使用注意事项，在自制造日起算的年限内，不会 产生对环境污染或人体及财产的影响。上述标识粘贴在机器背面。 • 有毒有害物质或元素的名称及含量 部件名称 有毒有害物质或元素 铅 汞 镉 六价铬 多溴联苯 多溴二苯醚 （Pb） （Hg） （Cd） （Cr（VI）） （PBB） （PBDE） 印刷电路板 × ○ ○ ○ ○ ○ 机箱 ○ ○ ○ ○ ○ ○ 液晶显示器 × ○ ○ ○ ○ ○ 其他 × ○ ○ ○ ○ ○ ○ ：表示该有毒有害物质在该部件所有均质材料中的含量均在 SJ/T 11363-2006 规定的限量要求以下。 × ：表示该有毒有害物质至少在该部件的某一均质材料中的含量超出 SJ/T 11363-2006 规定的限量要求。 ( 企业可在此处 , 根据实际情況对上表中打“×”的技术原因进行进一步说明 )
EIZO NANAO CORPORATION 153 Shimokashiwano, Hakusan, Ishikawa 924-8566 Japan Phone: +81 76 277 6792 Fax: +81 76 277 6793 EIZO Nordic AB Lovangsvagen 14 194 61, Upplands Väsby, Sweden Phone: +46 8 594 105 00 Fax: +46 8 590 91 575 中国苏州市苏州工业园区展业路8号中新科技工业坊5B Phone: +86 512 6252 0100 Fax: +86 512 6252 1508 http://www.eizo.com 5th Edition-November, 2011 Printed in Japan. 00N0L595E1 (U.
