User's Manual

1.Special Thanks 2.Contents
Thank you for your trust and support in purchasing
our product. Please read the user manual carefully
before using our product. In order to continuously
enhance the performance and quality of the
product and allow users to get a better experience
in using our product, we will keep improving and
optimizing this product. Thus design and
specifications are subject to change without notice.
Note:
Your satisfaction is our unremitting pursuit.
In case you have any questions about using the
product, please don't hesitate to contact us; we
will provide timely and satisfactory solutions.
Contact: [e-mail]
1) Complied Standards-------------------1
2) Product Overview and Accessories-----1-2
3) Main Parameters--------------------2-3
4) Operation Instructions---------------3-9
5) Troubleshooting-------------------9-12
3.Complied Standards
4.Product Overview and Accessories
1.This product is in compliance with the National
Standard Food and Drug Administration (FDA)
and Federal Communications Commission of
United States of America.
2.
This product complies with the regulation of
myopia glasses and reading glasses.
➀ Magnetic charging port
➁ Operation Button
➂ IR Light Sensor and LED indicator
➃ Microphone
➄ Bone Conduction Headphone
5.Main Parameters
CAUTION: Do not put your fingers on the hingear
when open glasses for wearing, in case it will
cause pinching.
Accessories:
Anti Blue Light&Photochromic Lenses; Lenses
Templates; Magnetic Charging Cable; Cloth Pouch;
User Manual
Ⅰ. Bluetooth System
Bluetooth Version 5.0
Connectable to Bluetooth competent mobile
phones, desktops, laptops, etc. Compatible with
profiles A2DP、APTX.
Stand-by time: Around 7 days
Continuous playback time:3-4 hours ( Different
volume and sound source will be different. )
Up to 10 meters barrier-free wireless range.
Battery specifications: 90 mAh/3.7V on each frame
side; Fully charge within 1 hour.
Speaker type : Bone conduction speakers
Power of speakers: 1W* 2
Speaker sensitivity : 102+3dB
Microphone sensitivity : -40+3dB
Frequency Range:20Hz ~ 20KHz
Illustrations for voice prompts
6.Operation Instructions
Ⅱ. Other technical specifications
Product dimension:155mm* 146mm* 49mm
Net weight: 38g(lenses included)
Operating environment:Temperature:-10c ~ 50c
Humidity:0~90%
Waterproof rating:IP66
Specification of charger:
Charger port: Magnetic
Input:AC 110V/220V. 50/60Hz
Output:DC 5V. MAX 1A
Note:
Always use PC USB port or 5V-1A charger
for charging; using fast charger will damage
battery life.
Voice prompts can be heard and the status of
LED indicator shows differently as per different
functions during the use of this product.
Status/Function Voice prompt
Power On Power On
Power Off Power Off
Enter Pairing Mode Pairing
Bluetooth Connected Connected
Bluetooth Disconnected Disconnected
Color of indicator and the corresponding status
Color of Indicator Status
Red(Solid) Charging
Blue(Solid) Fully Charged
Blue and Red (Simultaneous Flash) In Pairing Mode
Ⅰ. Turn On/Off
In the OFF status, press and hold either side
ON/OFF button for 3 sec to power on left or right
frame only, followed by a voice prompt “Power
On”. While press and hold both side ON/OFF
button for 3 sec to power on both left and
right frames simultaneously, followed by a voice
prompt “Power On”
In the ON status, press and hold the one side
ON/OFF button for 3 sec to power off left or
right frame only, followed by a voice prompt
“Power Off”; Press and hold both sides ON/OFF
buttons for 3 sec to power off both left and right
frames simultaneously, followed by followed by
a voice prompt “Power Off”.
5 6
7 8 9 10
11
12
13
14
432
Ⅱ. Bluetooth Connection
▼In the OFF status, press and hold either side
ON/OFF button for 3 sec to power on left or
right frame only, e.g. turn on left side frame.
After then, press and hold the ON/OFF button
of the other side frame for 10 sec,till the blue
and red light simultaneously flash and accompanied
with voice prompt first “Power On” and then turn to
“Pairing”. (The side in pairing status is the main
connection side )
▼Locate the Bluetooth menu on the device you
are using and select “Rocklion“, then click it for
Pairing.
▼
Notes:
1
➀
➀
➁
➁
➂
➃
➃
➄
➄
User Manual
Bone Conduction Glasses
Nothing in or on your ears
A new way to listen. Stay connected to the world
around you while discreetly listening to music with
a revolutionary open-ear audio design.
RK
A voice prompt "connected" can be heard
when pairing has succeeded.
1) For IOS system, when the main connection side
connects successfully with Bluetooth, the other side
frame will automatically interconnect with Bluetooth.
2) For Android system, after the main connection
side connects successfully with Bluetooth, a new
Bluetooth pairing request will pop up again in your
device and you need to manually click “PAIR” to
connect with Bluetooth.
(1)
Pair the glasses to a standby device for the first
use. After pairing, re-pairing is unnecessary for
the connection to the same device if “Rocklion”
isn't deleted from the Bluetooth menu of the
device. After the glasses are turned on, they will
automatically reconnect to the device or you can
select "Rocklion” for pairing from the Bluetooth
menu of this device
(2)
When you delete “Rocklion” from the Bluetooth
https://www.youtube.com/watch?v=wIRF_8YGzLk
Should you have any using questions about the
glasses, please scan the below QR or input the
link in your browser, you will redirect to operation
video with detailed instruction.
▼Follow the above instructions to turn on the glasses
and pair them to a mobile phone or a desktop.
▼Answer a Call: Single click the button on either
side to pick up an incoming call
Ⅳ. Answer/Make Calls
▼Reject a Call: press and hold the button on either
side for second and release
▼End a Call: Single click the button on either side
to hang up the call.
▼Radial the Last Number on call records only:
press and hold the button of the main connection
side with Bluetooth for 1 second.
▼ After Voice Assistant is activated, human
commands can be used to perform operations of
mobile phones with Voice Assistant supported.
Please refer to user manual of mobile phones for
Ⅴ. Voice Assistant
▼When glasses connected with Bluetooth, double
clicking the button of the main connection
side with Bluetooth to activate the Voice Assistant
(also called Voice Recognition)
Ⅵ. Charging
Use magnetic charging cable included and connect
the glasses to a standard USB interface on PC or a
standard 5V-1A USB charger. The LED indicator
will show solid red when charging and will turn sold
blue when charging is completed.
CAUTION: Please fully charge the glasses before
the first use. Do not use any fast chargers to charge
the glasses.
Ⅶ. Factory Reset
Q1: Does not turn on
Q2: Unable to pair
be not when you follow the instructions below.
Please consult the after-sales team of the manufacturer
who will provide you with recommendations and
solutions for these problems.
"power off" or not. If neither of the voice prompts,
it is concluded that the battery needs to be
charged.
▼It is recommended to reset the glasses to reset the
glasses to factory reset if it still cannot be turned on
after fully charged. Please follow previous steps for
factory reset.
▼If the problem still exists after factory reset, we
assume it has something to do with the failure of
the electric circuit.Please communicate with the
after-sales team of the manufacturer to get a
solution.
▼Make sure the battery (both side frames) isn't
dead and press ON/OFF button to check if there is
any voice prompt saying "power on". If not, please
press and hold ON/OFF button again for 3 secs to
check whether there is any voice prompt saying
▼Make sure the pairing mode is entered while LED
light flashes red and blue alternately, and voice
prompted “Pairing”. If you see the intermittent red
Voice Assistant operations.
Q3: Does not charge
mode. Follow the correct steps of pairing described
above.
▼It is recommended to reset it to factory default
if it still cannot get paired. Follow the correct
steps of pairing described above.
▼If the problem still exists after factory reset, we
assume it has something to do with the failure of
the electric circuit.Please communicate with the
after-sales team of the manufacturer to get a solution.
LED only, it means the glasses is powered on and
does not enter the pairing mode. Follow the correct
steps of pairing described above.
▼Check If the glasses have already been paired
with another device within 10 meters. If yes, the
solution is to delete the Bluetooth name
“Rocklion” from the menu of the device paired
and then follow the pairing steps to pair it with
the new device.
▼Try to remove all the Bluetooth names from the
menu of your phone and put it back to pairing
▼Check whether there is electricity on the power
outlet (check whether the socket switch is turned
off etc.)
▼Check whether the USB charger charges properly.
(Try to charge other devices with this USB charger to
(1) In the OFF status, charge both sides of the
glasses
(2) Press and hold the buttons of both sides for
15-20 seconds, do not release the bottons untill
the red light disappears and lights up again
(3) Unplug the charging cable, blue light will
working temperature should be -10~ +50°C.Using
the glasses in too cold/hot environment or highly
humid area will shorten the battery life.
Never leave the glasses in your car on a hot day.
Recharge the glasses after you leave them unused
Ⅷ. Storage & Maintenance
Store the glasses in cool and dry place. The
for a long period.
Clean the glasses with soft cloth.
Do not bring the glasses into contact with sharp
objects.
Notes:
1.It is not recommended to wear glasses to
shower or swimming to prevent the glasses from
malfunctioning in unexpected situations.
2.The sensitivity of light sensor may weaken or
even fail over long-time use, but it does not affect
the basic functions of the product.
7.Troubleshooting
You may come across some unexpected problems
during the use of this product.Some problems can
be solved quickly by yourself while the others may
flash, and then power on the glasses for pairing
(Factory reset is generally used when there is
electronic failure of the glasses)
Ⅲ. Play/Pause Music
▼Follow the above instructions to turn on the
glasses and pair them to a mobile phone or a
desktop.
▼Start a music player from your mobile phone
or desktop and wear the glasses to enjoy music.
▼Music stops playing when the music player is
closed from your mobile phone or desktop.
Operation instructions:
menu of a connected device, please power off the
glasses first and follow the previous steps of
Bluetooth connection for pairing with a new device
(3)
The glasses turn off automatically 14 minutes
after they are unconnected or fail to connect to
the device
(4)
If out of range (more than 10 meters) when
connected to a device, the glasses will disconnect
from the device. Once back within range, it will
automatically reconnect within 1 minutes. Single
click On/Off button to make the glasses reconnect
to the device if 5 minutes pass
(1)
Play/Pause: Single click On/Off button on
either side to pause music under playback status.
Single click On/Off button on either side to play
music under pause status.
(2)
Volume Adjustment and Song Switch:
One-button design has no access to multi-status
operations through the glasses; under playback
status, Operations like switching songs and
adjusting volume can be operated through
mobile phones.
(3)
Light-Sensor Switch and Power Saving Mode:
under playback status, taking off the glasses
from your head will trigger light sensor, and
music will automatically pause. When the light
glasses again within 5 seconds, and the music
playback will automatically continue, but after 5
seconds, you need to click the button on either
side to continue playing.
sensor triggers the music to pause, put on the
make sure the USB charger is in good condition.)
▼Check whether the LED shows sold red. If not,
it means charging isn't effective. LED turns blue
when charging is finished.
▼It is recommended to reset it to factory default
if it still does not charge.
▼If the problem still exists after factory reset, we
assume it has something to do with the failure
of the electric circuit.Please communicate with
the after-sales team of the manufacturer to get
a solution.
Q4: One side speaker doesn't work
▼Check whether there is electricity on the power
outlet (check whether the socket switch is turned
off etc.)
▼Check whether the USB charger charges
properly. (Try to charge other devices with this
USB charger to make sure the USB charger is in
good condition.)
▼It is recommended to reset it to factory default
if it still does not work.
▼If the problem still exists after factory reset, we
assume it has something to do with the failure
of the electric circuit.Please communicate with
the after-sales team of the manufacturer to get
a solution.
Federal Communications Commission (FCC) Statement
This device complies with part 15 of the FCC Rules.
Operation is subject to the following two conditions:
(1) This device may not cause harmful interference,
and (2) this device must accept any interference
received, including interference that may cause
undesired operation.
Note: This equipment has been tested and found to
comply with the limits for a Class B digital device,
pursuant to part 15 of the FCC Rules. These limits
are designed to provide reasonable protection a
gainst harmful interference in a residential installation.
This equipment generates, uses and can radiate radio
frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful
interference to radio communications. However, there
is no guarantee that interference will not occur in a
particular installation. If this equipment does cause
harmful interference to radio or television reception,
which can be determined by turning the equipment
off and on, the user is encouraged to try to correct
the interference by one or more of the following
measures:
●Reorient or relocate the receiving antenna.
●Increase the separation between the equipment
and receiver.
●Connect the equipment into an outlet on a circuit
different from that to which the receiver is connected.
●Consult the dealer or an experienced radio/TV
technician for help.
Warning: Changes or modifications made to this
device not expressly approved by SHENZHEN SHI
OUTUOYI MAOYIYOUXIANGONGSI may void the
FCC authorization to operate this device.
Note: The manufacturer is not responsible for any
radio or TV interference caused by unauthorized
modifications to this equipment. Such
modifications could void the user’s authority to
operate the equipment.
6) Federal Communications Commission (FCC)
Statement-------------------------13-14