Derringer Audio Transmitter T-2071-M DTC COMMUNICATIONS INCORPORATED
How to contact DTC Copyright Notice Warranty For operator and troubleshooting information, customers are encouraged to refer to the details in this manual. For additional clarification or instruction, or to order parts, contact DTC. Customer Service is available Monday through Friday between the hours of 9:00 AM and 5:00 PM EST at: 1-800-233-8639 Tel: 603-880-4411 Fax: 603-880-6965 Website: www.dtccom.com Email: info@dtccom.com Copyright © 2003 DTC Communications, Inc. All rights reserved.
TABLE OF CONTENTS Manual Conventions Overview ............................................................................. 4 NOTE Describes special issues you should be aware of while using a particular function. Quick Start ........................................................................... 5 WARNING Calls out situations in which equipment could be damaged or a process could be incorrectly implemented, but in which operator safety is not a factor. Connections .................................
.000 .250 Top View .420 .200 OVERVIEW .313 .145 Using The Derringer .210 MULTI-PIN CONNECTOR/ EXTERNAL MICROPHONE INTERNAL MICROPHONE ANTENNA .000 .000 Front View 1.100 The T2071-M Derringer is a small audio transmitter which can transmit a secure and clear audio signal. It has up to 10 programmable channels for the RF transmission, accessed through a PC with DTC programming software installed. The transmitter is designed for personal protection and evidence gathering missions.
QUICK START Using A Separate Microphone 2 Install the noodle antenna into the antenna connector on the transmitter. Adjust length according to band of operating frequencies. 3 Attach fresh batteries to the snap on connector. 4 Using a small screwdriver, turn the recessed rotary switch located on the front cover to the desired channel. The configuration of each channel is managed with DTC programming software.
TIPS PULL UP ON SECTION INDICATED TO RELEASE LOCK AND REMOVE Note: This is a push-on, pull off locking connector. The connector will rotate 360° in the transmitter without disconnecting. Use extreme caution when connecting or removing the noodle antenna. To remove pull the noodle antenna straight out. 3 6 Battery Operation: Always remove battery when not in use. It is imperative to discard partially used batteries, as their remaining life is not predictable.
CONNECTIONS ANTENNA (Male MMCX Connector) This connector accepts the noodle antenna. Top View Microphone Multi Pin Connector MICROPHONE The Derringer uses an internal electret microphone in addition to an external microphone MULTI-PIN CONNECTOR (Male multi-pin connector) This connector mates with the 36” external microphone and also mates with the programming cable and optional vehicular power adaptor model VPA-2001.
SPECIFICATIONS Front Cover View The Derringer measures just 2.1” by 1.1” by .4”; it provides ten user programmable channels and audio scrambling. Automatic gain control is programmable by channel as well. The Derringer contains an internal microphone, which is automatically disabled if an external microphone is attached. Power is provided by a convenient snap-on 9 Volt battery type connector.
SPECIFICATIONS ITEM SPECIFICATION AGC Range 45dB Microphone Electret-fet internal or external Spurious & Harmonics -50 dBc max non-harmonic, -45 dBc harmonic Operating Temp Range -30° C to +70° C Operating Voltage Range 6.0 to 9.
PROGRAMMING Introduction When you order a Derringer audio transmitter, DTC will factory program your frequencies at no additional charge to you. You may want to place a sticker over the rotary switch on the chassis so users in the field don’t attempt to change frequencies. This is often the best path for state and local agencies with limited frequencies available to them. DTC will also provide you with free software and a free programming cable, enabling you to change your transmit frequencies.
PROGRAMMING Installing DTC Universal Programming Software on your PC NOTE: Uninstall any previous versions by going to Add/ Remove Programs, clicking on DTC Universal Programming, and clicking on uninstall. 1 2 3 4 5 6 7 8 9 10 11 Click on Start, click on run. Click on the Browse button. Click on or find your CD drive. Install the JAVA Runtime Environment Application first (CD provided). Follow the install wizard screens. Install the Universal Programming software next (floppy provided).
PROGRAMMING 1 COM1 or COM2 Serial port of computer 2 Check that an antenna (or non-radiating load) is connected to the Derringer MMCX antenna port. Connect the DB9 end of the DTC programming cable to either the COM1 or COM2 port of the PC depending on port availability. Note: A 6-foot extension cable may be used between the PC and the DTC programming cable.
PROGRAMMING 8 9 Mouse-click OK or cancel. Now follow the instructions on the DTC Programming Application to begin the download and subsequent frequency reprogramming process.
ACCESSORIES Part Number Description 4044738 Programming Cable Part Number Description 4044377 4 “AA” Battery Pack Part Number Description 7011150 3’ Microphone Part Number Description 4045319 Noodle Antenna DTC Universal Programming Software DTC part number 14 8002025
Sales Representatives Director of Federal Sales John Morgan toll free (800) 233-8639 voice (603) 546-2122 cell (603) 320-3257 fax (603) 880-6965 jmorgan@dtccom.com Federal Sales Manager Marianne Caiazza toll free (800) 233-8639 voice (603) 546-2121 cell (603) 320-3256 fax (603) 880-6965 mcaiazza@dtccom.com Federal Sales Manager Wireless Video Products John Robey toll free (800) 233-8639 voice (703) 878-4375 fax (703) 680-7997 cell (571) 217-0599 pager (877) 468-1764 jrobey@dtccom.
486 Amherst Street • Nashua, New Hampshire 03063 • 603-880- 4411 www.dtccom.