User's Manual

9
Precautions
10
Check points before complaints about failure
Please use 5V-1A charger.
Please use the suitable charger and cable with the correct
voltage.
If you charge the product with the unofficial cable and
charger for a long time, the product can be damaged.
➡ The manufacturer has no responsibility on the issue
caused by the unofficial cable and charger.
The sticker is printed by moving back and forth in the slot
for 6 times.
▪ Please don't touch the paper during printing.
▪ Please don't pull out the paper during printing.
▪ Please don’t put something on slot for paper.
▪ Please use the newest app version fir the best printing quality.
➡ Please check the newest version of the app on the
Google Play Store and Apple App store.
▪ The printer has an inner battery. Please charge it before
using it.
▪ Please don't disassemble or deform it.
▪ Please avoid too high temperature and humidity.
▪ Proper temperature: 5~40℃
Cases Solutions
The printer doesn't work well. • Please check if the power button is turned on.
•
Please check the color of LED light.
The power is not turned on.
• Please connect the charger to the USB port.
• Please check if the charger operating well.
• Please check if the voltage on your state is
matched with the product's voltage.
The paper is jammed. •
Please turn on printer again after turning
it off. The paper is printed automatically.
•
Please reset the printer by putting the reset
hole by a sharp thing.
*
If you can't solve the issue with the above solutions, please contact to
CS center([phone]).
4
How to put the cartridge
5
How to pull out cartridge from the printer
STEP 3
Please put the upper cover on the printer by
pushing it to the right like the picture.
STEP 4STEP 2 STEP 3STEP 1 STEP 1 STEP 2
Please don't touch the paper and ribbon when
putting the cartridge.
STEP 1
Please open the upper cover by pushing it to the left like the picture.
STEP 2
Please put the cartridge into the same direction on the picture.
STEP 1
Please press both sides of the hook of the cartridge.
STEP 2
Please pull out the cartridge while pressing the hook.
STEP 3
Please press ‘PUSH’ button on the cartridge.
STEP 4
Please press the hook of the cartridge until there's clicked sound.
When cartridge is put into correctly : White LED
When cartridge is put into wrong : Red LED
*
STEP 3
Specification
▪
Model name: NP100
▪
Product name: NAILPOP
▪
Made in Vietnam
▪
Dimension: 39.5mm x 148mm x 101mm
▪
Rated voltage: 5V 1A
▪
Optimal temperature: 5~40ºC
▪
Optimal humidity: Under 70%
1
Components
2
Name for each component
3
Quick Start Guide
4
How to put the cartridge
5
How to pull out the cartridge
6
7
Transferring nail design to the product
8
Mobile application
9
Precaution
10
Check points before complaints about failure
User manual
STEP 1
Power on
Please press the power button
about 3 seconds.
STEP 3
App
Please choose a nail look design on the application.
STEP 2
Connect to Bluetooth
To connect to Bluetooth, please
search the printer on the setting
of your smartphone.
Ex) NailPOP XX:XX
Please select the nail pop printer
on the search list.
2
Name for each component
1
Components
3
Quick Start Guide
Power button
LED status indicator
Reset Button
LED charging indicator
USB port
Upper Cover
Strap Rubber
Slot for paper
*
About the details about LED indicator, please check from the NAIL POP APP.
USB‒type C(1EA) Nail File(1EA)Alcohol prep pads (5EA)
Cartridge (1EA)
STEP 4
Printing
You can print out by pressing
'Print' button on the app after
choosing a nail look design.
STEP 7
How to charge
You can charge the printer by
USB type-C enclosed in the set.
The red LED light is turned on
during charging and the green
LED light is turned on when the
printer is charged.
STEP 5
Attaching sticker
Please clean your nails by the
prep pad enclosed in the cartridge
box. And then, please attach the
nail sticker printed on your nail and
trim it by the nail file.
STEP 6
How to power off
Please press the power button
about 3 seconds.
LED 충전표시등
Specification of product
11
Specification of product
12
Contact Point
Paper (Medium 10EA)
6
8
Mobile Application
Search Nail POP App
by the QR code.
7
Transferring nail design
to the smartphone
700mAh
Battery
USB C- type
USB type
Bluetooth
Specification
(Red light: On charging /
Green light: Charging finished)
• Please check if the battery is charged.
11
12
Contact Point
TEL : 070 - 5117 - 4717
Homepage : http://www.nailpop.biz/
22.722.722.7
22.7
8.1 9.2 10.0 10.1 11.0
11.8
13.4
16.5
NAIL POP Printer (1EA)
Print Overview
Print Overview
You can design your own nail
look if you select the nail tip.
You can design your own nail
look if you select the nail tip.
You can design your own nail
look if you select the nail tip.
Print
Print
Print Overview
Print Overview
Precautions on
charging
General
precautions
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to
part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful
interference in a residential installation. This equipment generates, uses and can radiate radio frequency
energy and, if not installed and used in accordance with the instructions, may cause harmful interference to
radio communications. However, there is no guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference to radio or television reception, which can be
determined by turning the equipment off and on, the user is encouraged to try to correct the interference by
one or more of the following measures:
—Reorient or relocate the receiving antenna.
—Increase the separation between the equipment and receiver.
—Connect the equipment into an outlet on a circuit different from that to which the receivers
connected.
—Consult the dealer or an experienced radio/TV technician for help.
IMPORTANT NOTE : FCC RF Radiation Exposure Statement
This equipment complies with FCC RF radiation exposure limits set forth for an uncontrolled environment.
This equipment should be installed and operated with a minimum distance of 20 centimeters between the
radiator and your body. This transmitter must not be co-located or operating in conjunction with any other
antenna or transmitter. This device complies with part 15 of the FCC Rules.
Operation is subject to the following two conditions:
(1) This device may not cause harmful interference, and (2) this device must accept any interference received,
including interference that may cause undesired operation. IC Information to User This device complies with
Industry Canada’s licence-exempt RSSs.
Operation is subject to the following two conditions:
(1) This device may not cause interference; and (2) This device must acceptany interference, including
interference that may cause undesired operation of the device.
Le présent appareil est conforme aux CNR d’Industrie Canada applicables aux appareils radio exempts de
licence. L’exploitation est autorisée aux deux conditions suivantes :(1) l’appareil ne doit pas produire de
brouillage, et (2) l’utilisateur de l’appareil doit accepter tout brouillage radioélectrique subi, meme si le
brouillage est susceptible d’en compromettre le fonctionnement. Attention: Tout changement ou
modi_cation non expressément approuvé par le fabricant peut annuler le droit de l'utilisateur à utiliser
l'équipement. exposition aux rayonnements radiofréquences. Pour se conformer aux exigences de
conformité de l'exposition IC RF, une distance de séparation d'au moins 20 cm doit être maintenue entre
l'antenne de cet appareil et toutes les personnes.
Caution
THE GRANTEE IS NOT RESPONSIBLE FOR ANY CHANGES OR MODIFICATIONS NOT EXPRESSLY APPROVED BY
THE PARTY RESPONSIBLE FOR COMPLIANCE. SUCH MODIFICATIONS COULD VOID THE USER’S AUTHORITY TO
OPERATE THE EQUIPMENT.
User manual
front
back
810mm90mm
90mm