TDS

DRYLOK® Extreme Basement & Masonry Waterproofer
DRYLOK® is ideal for interior/exterior,
above/below grade masonry including
cinder and concrete block, stucco, brick,
and bare concrete swimming pools.
Features Flexible Encapsulated Polymers
for a beautiful, smooth waterproof nish.
Specically formulated to resist mildew
growth on the dry paint lm, with the
incorporation of a biocide. Tested to
ASTM D-7088 Resistance to Hydrostatic
Pressure and ASTM D-6904 Resistance to
Wind-Driven Rain. Stops 15 psi, greater
than a wall of water 33 feet (10 meters)
high! Fully transferable 15 year warranty.
Bright white, smooth finish
Resists mildew growth on the dry paint
film
Resists 15 PSI, equivalent to a wall of water
33 ft. high
Category 4-resists 140 MPH wind-driven
rain
Fully transferable 15 year warranty
Guaranteed to stop water, even under
pressure
Features flexible encapsulated polymers
Tintable
Ideal for interior, exterior, above or below
grade masonry walls, basement walls,
retaining walls, foundations, landscape
walls, cinder blocks, concrete blocks, bare
concrete swimming pools, stucco, and
brick.
DRYLOK® Extreme Basement & Masonry
Waterproofer may be applied over
previous coatings in sound condition, but
the warranty is void. Not formulated for
horizontal surfaces subject to foot traffic.
COMPOSITION:
Latex base
SHEEN:
N/A
% WEIGHT SOLIDS:
62-64%
DENSITY (LBS./US GAL.):
10.13-20.2 (1.21 ± 0.02 g/L)
VISCOSITY:
110-120 Ku @ 77ºF (25ºC)
pH:
9.0-10
COLOR:
• White – ready mixed formula
• 1 ready mixed color
DRY TIME:
• 2-3 hours
• To recoat: 2 hours
Note: Maximum cure and dry time
will be prolonged when slightly
humid and damp, cool conditions
prevail.
Note: When painting the inside of
concrete non-potable watertanks,
allow to dry at least 1 week before
puing into service.
CLEAN UP:
Warm soapy water
Dispose of contaminated absorbent,
container, and unused contents in
accordance with local, state, and
federal regulations.
COVERAGE (SQ. FT./GAL.):
First coat: Wet: 21 Dry: 10 mils @ 76
sq. ./gal.
Second coat: Wet: 13 Dry: 7 mils @
125 sq. ./gal.
Note: Actual coverage will vary
depending upon application
method, surface texture, and
porosity.
RECOMMENDED FILM THICKNESS/COAT:
21-13 wet mils/2 coats
(533-330 microns)
SHELF LIFE:
5 Years unopened container
FREEZE/THAW:
ree cycles
CONTAINER SIZES:
One quart (946 mL), One gallon
(3.785), and ve gallon (18.9 L)
containers
Does not exceed 100 g/L
Use alkali-proof universal tinting colorants.
Use only 50% of color normally
recommended. Do not use more than 2 .
oz. of colorant per gallon. (15 g/L).
Masonry surfaces must be clean and free
from dirt, dust, grease, oil, form release
compound, frost, or paint. Patch all holes or
cracks with DRYLOK® Fast Plug®, a fast
seing hydraulic cement, and smooth the
patch evenly with the surface around it.
Check the joint where the oor and wall
meet and ll any breaks with DRYLOK® Fast
Plug®.
EFFLORESCENCE, a white, powdery,
crystal-like deposit visible on the masonry
surface must be removed.
DRYLOK® Etch (liquid or powder) or
muriatic acid, used according to
UNITED GILSONITE LABORATORIES
MAILING: P.O. Box 70, Scranton, Pennsylvania, 18501
SHIPPING: 1396 Jefferson Avenue, Dunmore, Pennsylvania, 18509
T
OLL FREE: 1-800-UGL-LABS (845-5227)
P
HONE: 1-570-344-1202 • FAX: [phone]
www.UGL.com
D R Y L O K ® M A S O N R Y P R O D U C T S
O V E R
DRY TIME:
2-3 Hours
Recoat 2 Hours
CLEAN-UP:
Soap and Water
COVERAGE:
2 Coats Minimum
SPREAD RATE:
100 Sq. Ft./Gallon
07 14 16 COLD FLUID-APPLIED WATERPROOFING
09 91 13 EXTERIOR PAINTING | 09 91 23 INTERIOR PAINTING
DIV. 07 & 09