Thank You for Choosing Us! Get ready to enjoy your new JavaPod 1+ Single Serve Coffee Maker with Refill Kit! Instructions for the ConstantBrew refill system are included in a separate guide.
IMPORTANT SAFEGUARDS When using electrical appliances, basic safety precautions should be followed, including the following: 1. Read all instructions before using. 2. Do not touch hot surfaces. Use handles and knobs when available. Scalding may occur if the coffee brewer is moved or opened or K-Cup® Pack is disturbed during brewing cycles. 3. This appliance must be properly installed and located in accordance with these instructions before it is used. 4.
Please read all the instructions in this manual carefully before you begin to use this appliance. Proper care and maintenance will ensure a long life and a trouble-free operation for this appliance. Please save these instructions and refer to them for cleaning and care tips. SERVICING SHOULD BE PERFORMED BY AN AUTHORIZED SERVICE FACILITY. SAVE THESE INSTRUCTIONS SPECIAL CORD SET INSTRUCTIONS 1.
UNPACKING − Remove your coffee brewer from its packaging − After unpacking, please check that the following parts are included: 1. JavaPOD1+ Coffee Brewer 2. ContantBrew Refill System 3. ConstantBrew Installation Kit 4. K-Cup Optional Reuable Filter Holder 5. 50 White Paper Coffee Filters Note: − Check that your home power supply voltage is the same as marked on the machine rating plate − Destroy all the plastic bags to prevent danger to children.
ConstantBrew Refill System The ConstantBrew system refills the water reservoir automatically whenever the water level is low. ConstantBrew is designed to connect to water line that goes into a kitchen appliance for like a refrigerator. The following installation instruction is under the circumstance that you need 1/4 inch water line. If that is not the case, an adapter is required for the installation.
Installing The ConstantBrew Water Line Installation Overview Are you ready to impress your significant other, parents, or cat with your mad plumbing skills with ease? Let’s get started! Directly below, we’ve provided the option for a shortcut installation method. It requires that you have a ‘plastic’ water line (not copper or braided stainless steel) and don’t mind cutting it. However, if you need to be able to disconnect everything and return it to it’s initial state (i.e.
Installing The ConstantBrew Water Line Standard Installation Method Step #1 – Shutting off your water source. The images below illustrate the most common formats for your ice maker water source. Once you’ve located yours, shut off the valve. Drinkpod LLC 888 852 7873 www.drinkpod.
Installing The ConstantBrew Water Line Step #2 – Disconnecting your ice maker line. The images below illustrate what your water line may look like. To simply things, it’s either threaded (compression) or not threaded (quick connect). If it’s threaded, use a wrench or pliers to unscrew the compression nut at the end and disconnect it. If it’s not threaded, see the illustration at the bottom of the page for how to disconnect Quick Connect fittings.
Installing The ConstantBrew Water Line Step #3 – Connecting Assembly 1 to ice maker source. Now we want to hook up Connect Point (B1) on Assembly 1 to your water source. If your connection is threaded (1/4 in. O.D. compression): Screw Connect Point (E) on the Adapter (included with your kit) onto the threaded connection of your ice maker water source. If it’s not threaded, skip this part.
Installing The ConstantBrew Water Line Step #4 – Connecting Assembly 1 to ice maker. Now we want to hook up Connect Point (C1) on Assembly 1 to your ice maker (water line). If your hose is threaded (1/4 in. O.D. compression): Screw it onto Connect Point (D) on Assembly 2 (included with your kit. If it’s not threaded, skip this part.
Installing The ConstantBrew Refill System Step #7 – Remove JavaPod Reservoir Lid. Pull off the transparent lid on the reservoir mounted at the back of the JavaPod. Step #8 – Install the ContantBrew system. Insert the ConstantBrew system down and into the reservoir so that the port is located at the back. Step #9 – Connect water line. Insert the ConstantBrew system down and into the reservoir so that the port is located at the back. Step #10 – Turn on water.
Using The ConstantBrew Refill System ATTENTION You should always shut off the water valve: a) Before you remove the ConstantBrew system from the water reservoir. b) If the system will be unsupervised for long periods of time (i.e. vacation). Under no circumstance is Drinkpod responsible for any damages caused from failing to shut off the water valve. Usage Tips If you experience any dripping, use a wrench or pliers to tighten the hexagonal connector (see below).
Drinkpod LLC 888 852 7873 www.drinkpod.
POWER UP Place Brewer upright on a flat surface, remove all product packaging and plug into outlet. FILL THE RESERVOIR Option 1: Manual Fill Remove reservoir and reservoir lid, then fill with water to the MAX FILL line. Option 2: Direct Connect to a Water Source Please refer to the ConstantBrew Manual included in the box. SET RESERVOIR ON BREWER Replace reservoir lid and place reservoir on top Brewer.
Option 2: Choose your K-Cup Lift the handle of the brewer and insert a chosen K-Cup® pack into the k-cup pack housing. Do NOT peel off the foil cover of the k-cup pack. CAUTION: Avoid the sharp piercing pin inside the brew head (it will be hidden when the handle is opened) Close by pressing down on top of the brew head handle NOTE: K-Cup® pack will be punctured when closing the brew head. Place your coffee cup in the dispense area on the drip tray.
TIP FOR FIRST TIME USE: It is suggested to make a cup of water that will rinse the inside as well as help warm up the machine. How to change default coffee volume ( 6oz- 8 oz-10 oz): A. Leave the machine unplugged. B. Press the hold the small cup button while simutaneously inserting the plug into the socket.. C. The middle cup button is lit steadily, which stands for the factory default setting. D. You can press the small cup size to set the default volume at: 4oz- 6oz- 8 oz for the 3 buttons. E.
Helpful Hints • Initial Cleansing Brew – Before you use your JavaPOD Brewer for the first time, perform an initial cleansing brew by running clean water through the brew cycle without using a K-Cup® pack. • One Cup at a Time – Your new Brewer makes one fresh beverage at a time. • The Right Water Makes a Difference – For the best tasting gourmet coffee, tea or hot cocoa, we recommend using bottled or filtered water. We do not recommend using distilled or reverse osmosis water.
Cleaning the K-Cup® pack Holder Assembly 1. Cleaning the Parts – The K-Cup® pack Holder Assembly can be placed onto the top shelf of a dishwasher. NOTE: Use low temperature cycles in the dishwasher. To remove from the Brewer, lift the front face of the Brewer. Grasp the top of the K-Cup® pack Holder with one hand while twist clockwise on the bottom of the K-Cup® pack Holder to unlock it.
DE-SCALING YOUR JavaPOD Mineral content in bottled or filtered water varies. Depending on the mineral content of the water, calcium deposits or scale may build up in your Brewer. Scale is non-toxic but left unattended, it can hinder Brewer performance. Descaling your Brewer helps maintain the heating element, and other internal parts of the Brewer that come in contact with water. The Brewer should be de-scaled every 3-6 months to ensure optimal performance or when there are white deposits in the reservoir.
PROBLEM CAUSE SOLUTION 1) K-Cup® pack Holder may be clogged 2) Water is not enough to brew the selected size. 3) Calcium or scale is built up in the brewer. 1) Clean K-Cup® pack Holder if necessary and rinse under faucet Brewer is working but no water comes out in first time use or after long time no use . The pump is dry causing difficulty for priming. Plug the brewer in OFF mode, keep pressing the POWER button to initiate the pump till priming succeeds.
WARRANTY INFORMATION 1-YEAR LIMITED WARRANTY Drinkpod warrants that for a period of one year from the date of purchase, this product will be free from defects in material and workmanship. Drinkpod , at its option, will repair or replace this product or any component of the product found to be defective during the warranty period. Replacement will be made with a new or remanufactured product or component.