User's Manual

To change the camera
settings from their default
values, you must use the
Foream Connect App
(for details, see p13) .
Always ensure the Camera
lens is on top of the
camera to ensure video
and image capture is right
side up. To stand the
camera on a flat surface,
clip on a shirt or strap use
the STANDARD CLIP.
DOUBLE TAP the surface of
the camera when in
Video/Timelapse mode to
start recording/saving. The
camera Mode LED will begin
flashing RED. Double
tapping the surface again will
stop the camera.
Use the Standard Clip to
stand the camera on a
surface, clip the camera to
clothing or a strap in 90
0
increments or attached to
the Drift Lanyard.
When in Photo Mode
(YELLOW LED), double tap
the surface of the camera to
take a photo.
follow us
facebook.com/driftinnovation
vimeo.com/driftinnovation
instagram.com/drift_innovation
twitter.com/driftinnovation
DRIFTINN OVATIO N.C O M
contents
3—4
5—6
7—8
9—10
11—12
13—14
15—16
17—18
19—21
package contents | about your camera
initial setup | getting started
using the camera | using the standard clip
using the standard clip
mode selection | settings
connecting to Foream Connect App | Wi-F
connecting the camera | specifications
accessory guide
disclosures
about your compass
Lens
‘TAP’ Surface
MODE Button
MODE Status LED
A
B
F
D
C
E I
G
H J
Wi- Fi Status LED
Wi- Fi Button
USB Port (Micro-B )
Micro SD C ard Slot
Microphone
Reset Button
inside the box
USB Cable (Mic ro-B)
Drift Compass
Camera Unit
Standard Clip
Quickguide
Drift Lanyard
POWER ON AND OFF
MODE SETTINGS
getting startedinitial setup
1. Insert a class 6 or higher
Micro SD card (up to
32GB)
2. C onnect the camera via
Micro USB cable to a
powered USB port and
charge the battery for
approximately 2 hours
or until the MODE status
LED turns GREEN
Orientating the C amera UP
using the camera
Start/Stop Video/Timelapse
or Broadcast Stream
Taking A Photo
UP
using the standard clip
Inserting the camera
1. Put the camera into the base of the clip first
2. Pivot the camera towards the clip body
3. Ensure the clip arms are extended over the
camera edge securely.
1. 2. 3.
Releasing the camera
1. Push the clip upper arms gently over the camera edge.
2. Pivot the camera away from the clip body.
Rotating the camera in the clip
The camera can be used in the clip
in any orientation needed to ensure
the c amera lens is always on top
regardless of which direction is
acc essible for clipping.
Using the lanyard
Simply slide the lanyard loop
over the standard clip to
securely store and hang the
camera around your neck.
1. 2. 3.
using the standard clipusing the standard clip
3
4 5 6 7 8 9 10
Thank you for purchasing the Camera.
CUSTOMER SUPPORT
updates, customer support, news about our products and videos
from our users:
www.driftinnovation.com
If you have any suggestions, comments or concerns, please contact
our customer support team at:
[e-mail]
WARRANTY
Warranty does not apply if the product is damaged due to physical
abuse, mishandling, accident, fire, frostbite, water damage,
negligence or failure to follow the supplied operating instructions.
For more information on warranty, see:
driftinnovation.com/warranty
Press and hold the (MODE)
button for 2 seconds. The
camera will power on in the
The current camera mode is
indicated by the colour of the
Mode Status LED (for details,
see p11) .
To change the current
camera recording mode
press the (MODE)
button once. Changing
between Video, Photo
and Timelapse.
MODE NAVIG ATION
i