ENIGMA-XO SHOWER AND TUB DOOR INSTALLATION INSTRUCTIONS PLEASE REVIEW THIS ENTIRE MANUAL PRIOR TO INSTALLATION SHDR-61606220-## SD-61606220G-## ## = Hardware Finish: 02 - Polished Gold 03 - Polished Rose Gold 06 - Oil Rubbed Bronze 07 - Brushed Stainless Steel 08 - Polished Stainless Steel 09 - Satin Black 17 - Brushed Tuxedo 18 - Tuxedo 29 - Polished Gold Tuxedo 39 - Polished Rose Gold Tuxedo SHDR-61487620-## SHDR-61547620-## SD-61547620G-## SHDR-61607620-## SHDR6160762G-## SD-61727620G-## SHDR-6172762
This model is treated with DreamLine’s exclusive ClearMaxTM Glass technology. This is a specially formulated coating that prevents the build up of soap and water spots. Install the surface with the ClearMaxTM label towards the inside of the shower. Please note that depending on the model, the glass may be coated on either one or both surfaces. For best results, squeegee the glass after each use and dry with a soft cloth.
Section Title ClearMax® Coating Information Warnings and General Preparation Manual Selection Important Model Information Recommended Reinforcement Information Model Specific Preparation Tools Detailed Diagram 'A' of Shower Door Components & Parts List A Detailed Diagram 'B' of Shower Door Components & Parts List B Installation Steps Guide Block Installation Guide Rail Bracket Adjustment Upper Roller Assembly Installation Lower Roller Assembly Installation Roller Wheel Assembly Adjustment Procedure Vinyl Se
©2021 DreamLine® All Rights Reserved WARNING DISCLOSURE STATEMENT WARNING DISCLOSURE STATEMENT IMPORTANT • GENERAL PREPARATION • • DreamLine® reserves the right to alter, modify or redesign products any time without prior notice for product improvement and customer experience. Please refer to the model’s web page on DreamLine.com for the latest technical drawings, installation manuals, warranty information or additional product details.
©2021 DreamLine® All Rights Reserved Manual Selection IMPORTANT! This manual will describe the installation of the single threshold model of the Enigma-XO. Use this manual when installing the Enigma-XO single threshold model. ! NOTE For the ENIGMA-XO Enclosure Installation: Start with the Enigma-X/Enigma-XO Enclosure Return Panel Manual that is packaged with the return panel glass FIRST for the installation of the return panel glass, then use this manual for the installation of the door section.
©2021 DreamLine® All Rights Reserved Important Model Information A B C B A ! E D IMPORTANT INFORMATION REGARDING THE INSTALLATION OF THIS SHOWER DOOR G F *Right-hand door installation shown A B C Guide Rail Brackets must be firmly attached to the wall. Installation into a stud is strongly recommended. All of the guide rail bracket set screws must be accessible and tightened. D Thread Lock must be applied to the set screws in both stoppers.
©2021 DreamLine® All Rights Reserved Recommended Reinforcement Information Install studs OR install 2”x 6” wood blocking between the studs where the Guide Rail Brackets will attach to the wall 6” × 2” 6” × 2” th or re tu sho b ld de ck measure from threshold* (see list below) *Blocking height requirement (to center) as measured from the threshold or tub deck: Enigma Air / Sky = 73” for shower ht / 59” for tub ht Enigma-X / XO = 72-1/2“ for shower ht / 58-1/2” for tub ht Enigma-Z = 73-1/2” for shower
! 2-3/4” minimum threshold REQUIRED: No Out-of-Plumb Adjustment; Verify threshold and walls with a level Threshold must be level 2-3/4” minimum threshold ±0.0 ! ±0.0 Threshold must be level 2” Tile TIP Acrylic ©2021 DreamLine® All Rights Reserved Model Specific Preparation ” X6 Tub Contact the manufacturer of the base, tub or threshold material with any questions regarding the drilling of holes into their product. ! Drilling into a stud or 2×6 wood reinforcement is recommended.
©2021 DreamLine® All Rights Reserved Tools Tape Measure Level Drill Bit Ø1/8" (3mm) Drill Bit Ø3/16" (4mm) Drill Bit Ø1/4" (6mm) Pencil Drill Bit Ø5/16" (8mm) Phillips Screwdriver Drill Bit Ø3/8" (10mm) Silicone Soft Head Hammer Chop saw** **Use the proper saw blade to cut stainless steel.
ENIGMA-XO Shower and Tub Door Manual Ver 1 Rev 7 022022 Detailed Diagram ‘A’ of Shower Door Components 01 04 07 08 03 02 Panel Glass 05 Door Glass 04 01 10 08 13 06 19 30 The glass surface with the ClearMax™ label must be installed to face inside of the shower 14 12 *Right-hand door installation shown.
©2021 DreamLine® All Rights Reserved Parts List A 01 02 Door Stopper x2 x4 07 Glass-to-Rail Bracket x1 x2 Door Glass x1 x1 Guide Rail Bracket ST6×55 Large Truss Head Screw ENIGMA-XO Shower and Tub Door Manual Ver 1 Rev 7 022022 Handle x1 09a x2 10 x3 Top Guide Rail (for 48” or 60”) 06 08 09b Wall Anchor Ø5/16” (8mm) Panel Glass 05 04 Roller Assembly 03 Wall Anchor Ø3/8” (10mm) x2 11 x2 Allen Wrench (3,4,5 mm) x1set 9
©2021 DreamLine® All Rights Reserved Parts List 12 13 Guide Block (with caps) x1 14 Bulb Vinyl Strip x1 16 15 Dam Strip x1 18 ST4.2×55 Truss Head Screw Dam Strip End Cap x2 17 x1 19 x1 Vertical Vinyl Strip ST4.
ENIGMA-XO Shower and Tub Door Manual Ver 1 Rev 7 022022 Detailed Diagram ‘B’ of Shower Door Components 72” MODEL ONLY 24 Panel Glass Door Glass 23 Small Inline Panel Glass The glass surface with the ClearMax™ label must be installed to face inside of the shower 22 21 19 25 18 11 *Right-hand door installation shown.
©2021 DreamLine® All Rights Reserved Parts List B 72” MODEL ONLY 09b Wall Anchor Ø5/16” (8mm) x2 Allen Wrench (3,4,5mm) x1set Vertical Vinyl Strip x1 22 Small Inline Panel Glass Bottom Bracket 14 19 18 ST4.2×55 Truss Head Screw 11 21 Wall Bracket x1 23 x1 x1 Small Inline Panel Glass Glass-to-Rail Bracket x1 24 x1 Top Guide Rail (for 72”) x1 25 ST4.
ENIGMA-XO Shower and Tub Door Manual Ver 1 Rev 7 022022 Installation Steps 1 Top *at model height ________” ±0.0 W Middle ________” ±0.0 Bottom 2-3/4” minimum threshold ________” ! Threshold must be level 2-3/4” minimum Tools Needed NOTE The minimum threshold requirement for the ENIGMA-XO is 2-3/4” of flat threshold space.
ENIGMA-XO Shower and Tub Door Manual Ver 1 Rev 7 022022 2 The length to cut-off from the door side of the Top Guide Rail (#03) will be (L): Doo (no r End hole s) Model Width (-) Finished Opening (W) = Cut-off Length (L) **Use the proper saw blade to cut stainless steel.
ENIGMA-XO Shower and Tub Door Manual Ver 1 Rev 7 022022 3 08 07 01 Panel-end Door Stopper (#01) hole inside 07 doo Parts Needed r en d 01 outside x2 02 Inlin e Pa nel G lass 01 x1 03 Fig 3 x1 08 19 07 x2 08 outside x2 11 07 Glass-to-Rail Bracket Door end of guide rail Adjustment disk TIP Find and mark the location of the high spot on the outer surface of the adjustment disk with a felt tip pen to make adjustment easier to see.
ENIGMA-XO Shower and Tub Door Manual Ver 1 Rev 7 022022 4 72” MODEL ONLY 6-5/8” from wall Inline Pane l Gla ss NOTE Loosen the screw on the rear of the Glass-to-Rail Bracket (#21) with the supplied allen wrench and secure it to the Top Guide Rail (#24). It is NOT neccessary to fully dissassemble the bracket during installation.
ENIGMA-XO Shower and Tub Door Manual Ver 1 Rev 7 022022 5 rotate disk(s) to level rail Door end of guide rail High spot of Adjustment Disk bushing NOTE The Panel Glass (#02) must be installed to the outside of the Top Guide Rail (#03).
ENIGMA-XO Shower and Tub Door Manual Ver 1 Rev 7 022022 6 72” MODEL ONLY Parts Needed 11 outside outside x1set 19 x1 23 NOTE For single threshold installation (shown), this bracket will be installed into the wall. For an enclosure installation only, this bracket will need to be installed into the threshold.
ENIGMA-XO Shower and Tub Door Manual Ver 1 Rev 7 022022 7 72” MODEL ONLY 1 2 3 Parts Needed 11 x1set 21 x1 23 x1 Tools Needed Fig 7a Fig 7b 19 ©2021 DreamLine® All Rights Reserved
ENIGMA-XO Shower and Tub Door Manual Ver 1 Rev 7 022022 8 Panel end Door end inside inside Guide Rail Bracket (#08) Glass-to-Rail Bracket (#07) Fig 8a *Right-hand door installation shown. inside outside Parts Needed 12 Fig 8b 9 overhead view of threshold & guide block 72” MODEL ONLY x1 *72” Model Only 22 inside inside 90° x1 Inline Panel glass Tools Needed 20 ! Guide Block (#12) must be installed square to the plane of the glass.
ENIGMA-XO Shower and Tub Door Manual Ver 1 Rev 7 022022 10 Fig 10a Fig 10b Fig 10c sleeve 72” MODEL ONLY base NOTE 21 ! Separate the Guide Rail Bracket (#08) base from the sleeve by loosening the set screws. Leave the sleeves on both ends of the Top Guide Rail. For enclosure installation only: remove the Guide Rail Bracket (#08) base on the side that will meet the Return Panel and refer to the Enigma-X/Enigma-XO Enclosure Return Panel Manual.
ENIGMA-XO Shower and Tub Door Manual Ver 1 Rev 7 022022 11 Ø3/8” or Ø1/4” drill bit Ø3/8” or Ø1/4” drill bit *see NOTE *see NOTE Ø3/16” or Ø5/16” drill bit Ø3/16” or Ø5/16” drill bit 72” MODEL ONLY *see NOTE *see NOTE Fig 11 NOTE For Guide Rail Brackets: ◾If a stud is present behind the wall: drill a Ø1/4”(6mm) hole up to the stud. (recommended) OR ◾If no stud is present behind the wall: drill a Ø3/8”(7mm) hole and install the Wall Anchor (#09a).
ENIGMA-XO Shower and Tub Door Manual Ver 1 Rev 7 022022 12 NOTE Leave the corner protectors on the glass until it is necessary to remove them safety set screw (align to the top) TIP outside e insid 72” inside MODEL ONLY Parts Needed 04 x2 10 Fig 12 x2 11 *right-hand door installation shown NOTE ! The adjustment set screws within the Guide Rail Bracket (#08) must be aligned vertically for easier access to adjust for level if necessary after the glass is installed.
ENIGMA-XO Shower and Tub Door Manual Ver 1 Rev 7 022022 Guide Block Installation 13a 3 NOTE 2 Contact the manufacturer of the base, tub or threshold material with any questions regarding the drilling of holes into their product. 4 1 use pencil or a center punch to mark the hole. Parts Needed 11 x1set 17 ST4.2×40 Fig 13a x1 Tools Needed M5×10 24 Part #12 - Guide Block (with caps) NOTE ◾For installation into an Acrylic Threshold: drill a Ø1/8”(3mm) hole and use the ST4.
ENIGMA-XO Shower and Tub Door Manual Ver 1 Rev 7 022022 Guide Block Installation 13b 72” MODEL ONLY 3 4 2 1 use pencil or centerpunch to mark the hole. Parts Needed 11 x1set 17 Fig 13b Part #22 - Small Inline Panel Glass Bottom Bracket NOTE ◾For installation into an Acrylic Threshold: drill a Ø1/8”(3mm) hole and use the ST4.2 x 40mm Countersunk Screw (#17). OR ◾For installation into a Tile Threshold: drill a Ø3/16”(4mm) hole up to the stud and use the ST4.2 x 40mm Countersunk Screw (#17).
ENIGMA-XO Shower and Tub Door Manual Ver 1 Rev 7 022022 14 Guide Rail Bracket Adjustment TIP Adjust the installed Top Guide Rail (#03) to level as necessary using the Guide Rail Brackets (#08) first and then the Glass-to-Rail Brackets (#07). Start adjustments from the door end. To lower the rail: Loosen the top set screw and tighten the bottom set screw. To raise the rail: Loosen the bottom set screw and tighten the top set screw.
ENIGMA-XO Shower and Tub Door Manual Ver 1 Rev 7 022022 15 72” MODEL ONLY (L) (X) (X) + 3/8” Measure the distance ‘X’ from the Guide Block (#12) to the wall and add 3/8”. (L) + 3/4” Measure the distance ‘L’ between the guide blocks and add 3/4”. Fig 15a Fig 15b Parts Needed 15 x1 Tools Needed 48”, 54“ or 60” Model Size: Cut the Dam Strip (#15) to the size of: (X) + 3/8”. NOTE 72” Model Size: Cut the Dam Strip (#15) to the size of: (L) + 3/4”.
ENIGMA-XO Shower and Tub Door Manual Ver 1 Rev 7 022022 16 1 2 3 4* 72” MODEL ONLY only use cap when installing up to a wall (for 48” & 60” model) Parts Needed 16 Fig 16 NOTE 28 For the 72” Model: Insert the Dam Strip (#15) into the Small Inline Panel Glass Bottom Bracket (#22). (Fig 16.
ENIGMA-XO Shower and Tub Door Manual Ver 1 Rev 7 022022 17 18 Guide Block (#12) face plate Fig 17 Fig 18 Parts Needed 11 x1set Tools Needed TIP Secure the Dam Strip (#15) to the threshold with several pieces of painter’s tape until the silicone fully cures. NOTE Attach the Guide Block face plate to the installed Guide Block (#12).
ENIGMA-XO Shower and Tub Door Manual Ver 1 Rev 7 022022 19 72” MODEL ONLY 1 2 3 Parts Needed 19 Fig 19 x1 21 4 x1 22 20 x1 Guide Block (#12) face plate 23 ide outs Fig 20 NOTE x1 Tools Needed Secure the Dam Strip (#15) to the threshold with several pieces of painter’s tape until the silicone fully cures.
ENIGMA-XO Shower and Tub Door Manual Ver 1 Rev 7 022022 Upper Roller Assembly Installation 21 1 2 safety set screw (must be on top) Panel Door Glass Glass ! inside **add threadlock to the safety set screw and wheel bolt e insid Adjustment Disk Neutral Position 3 Lower glass Raise glass Roller Assembly Wheel Adjustment TIP TIP NOTE e insid Mark the location of the high spot on the outer surface of the adjustment disk with a felt tip pen to make adjustment easier to see.
ENIGMA-XO Shower and Tub Door Manual Ver 1 Rev 7 022022 Lower Roller Assembly Installation 22 1 ! 2 ins ide **add threadlock to the safety set screw and wheel bolt 3 ins ins ide ide safety set screw (align to the top) front view Top Guide Rail safety set screw (align to the bottom) side view Parts Needed TIP NOTE Mark the location of the high spot on the outer surface of the adjustment disk with a felt tip pen to make adjustment easier to see.
©2021 DreamLine® All Rights Reserved Roller Assembly Adjustment Procedure for: Enigma, Enigma-X, Enigma-XO To create a good seal with the wall and to achieve minimal clearance beneath the door glass without making contact with the bottom guide block or threshold. Have at least two 3/16” shims or wedge shims (to maintain space beneath the door glass) and an assistant available to help with this procedure. Adjust only one wheel at a time.
ENIGMA-XO Shower and Tub Door Manual Ver 1 Rev 7 022022 Vinyl Seals & Handle Installation 23 door glass door glass door glass wall small inline panel panel glass Parts Needed 06 x1 outside 13 x1 Fig 23 14 *Right-hand door installation shown. NOTE TIP For the 72” Model: Attach the Vertical Vinyl Seal (#14) to the edge of the Small Inline Panel Glass (#23). The Bulb Vinyl Seal (#13) is not necessary with the 72” model.
ENIGMA-XO Shower and Tub Door Manual Ver 1 Rev 7 022022 Door Stopper Installation 24 1 2 3 4 ! 5 door 6* side small inline panel glass Position the door-side Stopper (#01) to allow enough clearance for the handle. 2” minimum 3” (+/- 1/8”) Parts Needed 01 approximately x2 11 35 Door Stopper Installation: 1. Remove the set screw 2. Slide the Door Stopper (#01) onto the Top Guide Rail (#03) 3. Align with stopper hole in the guide rail (inline panel side only) (Fig 24.2) 4.
REMOVE 3M™ TAPE ne l wa or gl as s in lin e pa ll do ENIGMA-XO Shower and Tub Door Manual Ver 1 Rev 7 022022 SafeStop™ Bumper Installation - Option 1 25 wall inside Fig 25 *Right-hand door installation shown. inside NOTE TIP The SafeStop™ Bumper (#30) is reversible for left or right wall installation. Install the SafeStop™ Bumper (#30) using the 3M™ tape. Screwing the SafeStop™ Bumper to the wall is optional (see step 26*).
2 3 6 wa ne l 1 REMOVE 3M™ TAPE 4* 5* 7 8 in lin e pa ll do or gl as s ENIGMA-XO Shower and Tub Door Manual Ver 1 Rev 7 022022 SafeStop™ Bumper Screw Installation - Option 2 26 Fig 26 inside TIP ! NOTE Extender driver bit recommended for screw installation. Parts Needed *Right-hand door installation shown. NOTE 09b For installing the SafeStop™ Bumper:: ◾If a stud is present behind the wall: drill a Ø3/16”(4mm) hole up to the stud.
ENIGMA-XO Shower and Tub Door Manual Ver 1 Rev 7 022022 27 NOTE The surfaces need to be clean and free of debris before applying silicone. 24 Hours ! Allow 24 hours for the silicone to cure before using the shower. 24 Hours ! 38 DO NOT hang or drape a towel or wash cloth over the Enigma Top Guide Rail as this may cause the Roller Assembly wheels to get stuck and possibly cause serious damage or injury.
©2021 DreamLine® All Rights Reserved Product Maintenance BASES and BACKWALLS: To ensure long lasting life for your acrylic back walls: wipe them off after each use with a soft cloth. To clean the acrylic back walls use non-abrasive sprays or cream based cleaners. Avoid the use of aerosol spray cleaners. Never use abrasive cleansers, metal brushes or scrapers that could permanently scratch or dull the surface.
©2021 DreamLine® All Rights Reserved Troubleshooting Problem/Symptom Missing Parts Top Guide Rail (#03) was cut too short or was cut from wrong end during installation. Water Leakage The door rolls open or closed The door does not track smoothly Door travels too far in either direction Mishandled glass TIP Suggested Solution •Check all shipping/packaging material for missing parts/components. •If not found, contact DreamLine® Customer Support [1-866-731-2244] to order factory part replacement.
ENIGMA-XO Shower and Tub Door Manual Ver 1 Rev 7 022022 Factory Parts Information 60x62 ENIGMA-XO Tub {SHDR-61606220-##} SHDR-61606220-## SD-61606220G-## ## = Hardware Finish: 02 - Polished Gold 03 - Polished Rose Gold 06 - Oil Rubbed Bronze 07 - Brushed Stainless Steel 08 - Polished Stainless Steel 09 - Satin Black 17 - Brushed Tuxedo 18 - Tuxedo 29 - Polished Gold Tuxedo 39 - Polished Rose Gold Tuxedo G - Smoke Gray Glass ITEM # 01 02 03 04 05 06 07 08 09a 09b 10 11 12 13 14 15 16 17 18 19 26 30 FACTO
ENIGMA-XO Shower and Tub Door Manual Ver 1 Rev 7 022022 Factory Parts Information 48x76 ENIGMA-XO Shower {SHDR-61487620-##} ITEM # 01 FACTORY PART NUMBER 07021036 / 07025036 / 07026036 / 07029036 / 0702G036 / 0702R036 Door Stopper 02 010112001 Panel Glass 03 Top Guide Rail 14 07121043 / 07125043 / 07126043 / 07129043 / 0712G043 / 0712R043 07351006 / 07355006 / 07356006 / 07359006 / 0735G006 / 0735R006 010114003 07221003 / 07225003 / 07226003 / 07229003 / 0722G003 / 0722R006 07021104 / 07025104 / 0
ENIGMA-XO Shower and Tub Door Manual Ver 1 Rev 7 022022 Factory Parts Information 54x76 ENIGMA-XO Shower {SHDR-61547620-##} ITEM # 01 02 03 04 05 06 07 08 09a SHDR-61547620-## SD-61547620G-## ## = Hardware Finish: 02 - Polished Gold 03 - Polished Rose Gold 06 - Oil Rubbed Bronze 07 - Brushed Stainless Steel 08 - Polished Stainless Steel 09 - Satin Black 17 - Brushed Tuxedo 18 - Tuxedo 29 - Polished Gold Tuxedo 39 - Polished Rose Gold Tuxedo G - Smoke Gray Glass 09b 10 11 12 13 14 15 16 17 18 19 26 30 FA
ENIGMA-XO Shower and Tub Door Manual Ver 1 Rev 7 022022 Factory Parts Information 60x76 ENIGMA-XO Shower {SHDR-61607620-##} SHDR-61607620-## SHDR6160762G-## ## = Hardware Finish: 02 - Polished Gold 03 - Polished Rose Gold 06 - Oil Rubbed Bronze 07 - Brushed Stainless Steel 08 - Polished Stainless Steel 09 - Satin Black 17 - Brushed Tuxedo 18 - Tuxedo 29 - Polished Gold Tuxedo 39 - Polished Rose Gold Tuxedo G - Smoke Gray Glass ITEM # 01 02 03 04 05 06 07 08 09a 09b 10 11 12 13 14 15 16 17 18 19 26 30 FA
ENIGMA-XO Shower and Tub Door Manual Ver 1 Rev 7 022022 Factory Parts Information 60x76 ENIGMA-XO Shower {SHDR-61607620-##} ITEM # SHDR-61727620-## SD-61727620G-## SHDR-61127620-## ## = Hardware Finish: 02 - Polished Gold 03 - Polished Rose Gold 06 - Oil Rubbed Bronze 07 - Brushed Stainless Steel 08 - Polished Stainless Steel 09 - Satin Black 17 - Brushed Tuxedo 18 - Tuxedo 29 - Polished Gold Tuxedo 39 - Polished Rose Gold Tuxedo 72” MODEL ONLY FACTORY PARTS INFORMATION FACTORY PART NUMBER ITEM DESCR
TEL: 866-731-2244 FAX: 866-857-3638 DREAMLINE.COM For more information on DreamLine® Shower Doors and Enclosures please visit DreamLine.
