ALLURE SHOWER DOOR INSTALLATION INSTRUCTIONS IMPORTANT DreamLine® reserves the right to alter, modify or redesign products at any time without prior notice. For the latest up-to-date technical drawings, manuals, warranty information or additional details please refer to your model’s web page on DreamLine.
Preparation 1. Prior to installation, examine all boxes and packages for shipping damage and compare the piece count with your packing slip. After opening all boxes and packages read this introduction carefully. Check that all of the needed parts are included in the package by checking off the components on the “Detailed Diagram of Shower Door Components”.
NOTE: The installation of this model requires that you drill down into the threshold (see step# 8).
Detailed Diagrams of Shower Door Components Diagram A Diagram B 33* Packing List A 01 02 03 04 05 06 07 08 09 10 11 12 Wall profile for small stationary glass Glass profile for small stationary glass Small stationary glass Glass door Glass profile Wall profile Handle Pivot retainer Pivot bracket(top and bottom) Glass fixer(top and bottom ) Washer Pivot assembly(upper and lower) 1pc 1pc 1pc 1pc 1pc 1pc 1pair 2pcs 1pair 1pair 2pcs 1pair 13 14 15 16 17 18 19 20 21 22 23 24 Fixing nut with M4×12 screw So
Shower Door Top View Diagram Top view of left hand single swing door installation Requires 2-1/4” minimum threshold 15/16” NOTE: The strike side wall profile (or panel glass) is offset into the shower from the pivot side by 15/16” “Allure” manual Ver.
Shower Door Installation 1. Place the Wall profile for small stationary glass (01) on the threshold vertically and align against the finished wall. Adjust the Wall profile for small stationary glass (01) position and level it. Mark the drilling holes on the wall through the predrilled holes in the Wall profile for small stationary glass (01). Now drill the holes in the wall using Ø5/16” drill bit and insert the Wall anchors (15). 1 2 See Fig.
3. Apply silicone along the Wall profile for small stationary glass (01) and around the holes. Fasten the Wall profile for small stationary glass (01) and Pivot retainer (08) to the wall with the Round head screws ST4.2×40 (18). 1 See Fig. 3 for details 2 3 Fig. 3 4. Apply clear silicone along the inner channel of the Glass profile for small stationary glass (02) and push the Small stationary glass (03) inside the channel.
5. Attach the Pivot brackets (09) to the top and the bottom end of the assembled Small stationary glass (03) and the Glass profile for small stationary glass (02) with the Flat head screws ST4.2×25 (17). 1 See Fig. 5 for details 2 Fig. 5 6. Assemble the Glass fixer (10) to the top and the bottom hole at the Small stationary glass (03). Fasten the top Glass fixer (10) to the top Pivot bracket (09) using the Fixing nut with M4×12 screw (13) and cover the screw location with the decorative cap.
7. Slide the Small stationary glass (03) assembly into the groove of the Wall profile for small stationary glass (01). See Fig. 7 for details. 1 2 Fig. 7 8. Secure the upper Pivot bracket (09) to the upper Pivot retainer (08) with Socket head screw M6×6 (14). Use a level while adjusting the Small stationary glass (03) vertically and secure it in the place by tightening the Socket head screw M6×6 (14).
9. Attach the top and the bottom Pivot assemblies (12) to the Pivot brackets (09). Make sure the Washer (11) is in between Pivot assemblies (12) and Pivot brackets (09) and the rubber gaskets are between the glass and the metal. Slide the Glass door (04) into groove of the Pivot assemblies and tighten the provided fasten bolts. Push the Magnetic strip on door (23) onto the vertical edge of the Glass door. 1 2 3 4 See Fig.
10. Push the Glass profile (05) into the groove of the Wall profile (06) and push the Magnetic strip on jamb (24) into the groove of the Glass profile (05). Close the Glass door (04). Adjust the position of the Glass door (04) and position of the Wall profile (06) on the wall to ensure the Magnetic strips are able to contact each other properly. In this process, you have to use a level to ensure that the Glass door is absolutely vertical.
. Mount the Handle (07) onto the Glass door (01). Cut the Bottom anti-water strip (21) to size using a utility knife and attach it onto the bottom of the door glass with the flange facing into the shower. See Fig. 12 for details 1 2 Fig. 12 13. Apply a good quality mildew resistant silicone sealant between the base or threshold and the pivot bracket. Also, apply silicone between the wall and the wall profiles. See Fig.
Stationary Glass Installation 14. Apply clear silicone along the inner channel of the Glass profile (05) and push the Stationary glass (25) inside the channel. Push the Magnetic strip (33) on the vertical edge of the Glass door (04). NOTE: If you have difficulty sliding the Glass profile over the Stationary glass (25), you can slightly tap on the Glass profile (05) with a rubber mallet and a piece of wood. Please do not strike directly on the profile or on the edge of the glass panel.
16. Slide the Stationary glass (04) with the Glass profile (05) back into the groove of the Wall profile (06). Re-adjust the Glass door (04) and the Stationary glass (04) panel so that the Magnetic strips (33) are fully aligned. 1 Inside 2 See Fig. 16 for details. 3 4 Inside Fig. 16 17. Install the Bottom Bracket (32) onto the Stationary glass (04). Make any final adjustments to the panel, then drill a hole into the Shower base or threshold using an Ø1/8” drill bit. Use a Round head screw ST4.
18. After all final adjustments of the Assembled unit are made, drill three holes from inside of the shower through the first layer of the both the Wall profiles and the Glass profiles using an Ø1/8” drill bit. Secure the Wall profile and the Glass profile together with the Round head screws ST4.2×10 (16) and washers. Cover the screw heads with the Decorative covers (20). 2 1 Ø1/8” Inside 3 Inside 4 Ø1/8” See Fig. 18 for details 5 6 Fig. 18 19. Mount the Handle (07) onto the Glass door (01).
Glass shelves installation 20. Mark the Glass shelf (34) position on the wall. According to the measurements in Fig. 20.1, mark the drilling holes on the wall for the Shelf brackets (26). Drill the holes using a Ø5/16” drill bit and insert the Wall anchors (28). Attach the Shelf brackets (26) to the wall using the Flat head screw ST4.2×40 (29) and attach the Shelf brackets (27) to the Stationary glass (25). Insert the Glass shelves into the Shelf brackets and fasten the screws at the bottom of the brackets.
21. Apply a good quality mildew resistant silicone sealant between the base or threshold and the pivot bracket. Also, apply silicone between the wall and the wall profiles. See Fig. 22 for details. Waterproof Silicone Left hand swing installation Fig. 22 Right hand swing installation Fig. 23 “Allure” manual Ver.
Product Maintenance BASES and BACKWALLS: To ensure long lasting life for your acrylic back walls: wipe them off after each use with a soft cloth. To clean the acrylic back walls use non-abrasive sprays or cream based cleaners. Avoid the use of aerosol spray cleaners. Never use abrasive cleansers, metal brushes or scrapers that could scratch or dull the surface. GLASS: To ensure long lasting life for your glass shower products: wipe them off after each use with a soft cloth.
TEL: 866-731-2244 FAX: 866-857-3638 DREAMLINE.COM For more information on DreamLine® Shower Doors and Enclosures please visit DreamLine.com “Allure” manual Ver.