ELEGANCE SHOWER DOOR/ENCLOSURE INSTALLATION INSTRUCTIONS MODEL: __________ STYLE: __________ SELECTOR: __________ Please choose your door model, style and selector according to your order for easy installation. IMPORTANT DreamLineTM reserves the right to alter, modify or redesign products at any time without prior notice. For the latest up-to-date technical drawings, manuals or any other details please refer to the support.BathAuthority.com web page.
Preparation 1. After opening all boxes and packages, read this introduction carefully. Check that all of the needed parts are included in the package by marking all the components on the “Detailed Diagram of Shower Door Components”. Examine boxes and packages for shipping damage. If the unit has been damaged, has a finishing defect, or has missing parts, please contact our customer support department within 5 business days of the delivery date.
Detailed Diagrams of Shower Door Components Diagram: A Diagram: B 22 12 1 2 3 4 Diagram: C 21 5 22 21 23 13 7 25 23 26 24 27 25 14 15 16 8 9 6 28 17 26 27 10 29 28 18 30 11 29 31 19 32 Diagram: A 01 02 03 04 05 06 07 08 09 10 Wall profile for glass door Glass profile for glass door Glass door Glass profile Wall profile Handle Pivot assembly (upper and bottom) Pivot retainer (upper and bottom) Decorative cover Anti-water strip 1pc 1pc 1pc 1pc 1pc 1set 1pair 1pair 8pcs 2pcs
NOTE: Unpack your unit carefully and inspect it. Lay it out and identify all parts using the detailed diagram and packing list in your manual as a reference. Before discarding the carton, check for small hardware bags that tend to fall to the bottom of the box. If any parts are damaged or missing, please contact DreamLineTM for replacement. NOTE: Retain these installation instructions for future reference.
Self-Closing Pivot Assembly Parts List A B C D E F Flat head bolt M4×8 Pivot bracket Pivot axis Washer A Washer B Pivot body “ELEGANCE” Ver.4 Rev.
Style “A”: Single Shower Door Assembly and Installation NOTE: Use parts from Diagram “A” for the Single Shower door assembly and installation. 1 1. Place the Wall profile for glass door (01) on the shower base or the threshold vertically against the finished wall. Adjust the Wall profile for glass door vertically using a level. Mark the drill holes on the wall through the predrilled holes in the Wall profile for glass door. Now drill holes in the wall and insert the Wall anchors (12). ±0.
2. Push the Pivot retainers (08) into both ends of the Wall profile for glass door (01). 1 3 2 4 See Fig. 2 for details. Fig. 2 3. Run a silicone bead along the holes on the wall. Attach the Wall profile for glass door (01) and Pivot retainer (08) to the wall using Big flat head screws ST4.2×40 (16). 1 See Fig. 3 for details. 2 3 Fig. 3 “ELEGANCE” Ver.4 Rev.
4. Attach the Pivot assembly (07) to the top and the bottom ends of the Glass profile for glass door (02) with the Flat head screws ST4.2×25 (15) and M4×16 bolt (13). 1 See Fig. 4 for details. NOTE: The Back plate (K) of the Pivot assembly should face inside of your shower. 2 3 Fig. 4 5.
NOTICE: The Glass door has 2 cuts for the Pivot assemblies. The deeper cut must be on the top. 6. Remove the Bolts (L) and Back plates (K) from the upper and bottom Pivot assemblies (07). Place the Glass door (03) to the Pivot assemblies, attach Back plates (K) to its position and fasten tight the Bolts. Make sure the clear rubber Spacers (J) are in between the glass and the metal parts. Secure tight the Glass door to the Pivot assemblies. 1 2 See Fig 6 for details. Fig. 6 7.
8. Open the Glass door (03). See Fig. 8 for details. Fig. 8 9. Close the hole in the bottom Pivot retainer (08) with Flat head socket bolt M6×12 (18) or you can attach the Pivot retainer to the Shower base or threshold using Big flat head screw ST4.2×40 (16). Apply silicone sealant over the Screw (16) or Bolt (18) to prevent leakage. 3 1 See Fig. 9 for details. 2 Fig. 9 “ELEGANCE” Ver.4 Rev.
10. Push the Anti-water strip (10) into the vertical groove of the Glass profile for glass door (02). Attach the Bottom anti-water strip (11) onto the glass door. (You can cut the strips to size by using a knife). 1 4 2 5 See Fig. 10 for details. 3 Fig. 10 “ELEGANCE” Ver.4 Rev.
ATTENTION: Steps 11-16 Follow these steps if the width of your door is less than 37¾” and you are installing the door without stationary glass and you only need to refer to (Diagram A) to complete the installation. Steps 17-24 Follow these steps if the width of your door is 37¼” and over, and you are installing the door and the stationary glass with glass shelves and you have to use (Diagram A and B) to complete the installation. 11.
12. Use a level to ensure that the Glass door (03) and the Wall profile (05) is absolutely vertical. Draw a line along the vertical edge of the Wall profile on the wall. Detach the Wall profile from the Glass profile (04). Place the Wall profile to the outlined position and mark the drilling holes through the predrilled holes in the Wall profile. Drill the holes using Ø 5/16” drill bit in the wall 2 1 3 See Fig. 12 for details. 4 Ø5/16” Fig. 12 13.
. Adjust the width of the Glass door (03) by pulling out the Glass profiles (02) and (04) if it necessary for size of your door. Adjust the Glass door using a level and tighten in place with the Round head socket bolt M6×12 (17). Close the glass door and make sure that there is 1/16" - 1/8" gap between the glass door and the anti-water strip. See Fig. 14 for details. 1 3 ±0.0 2 1/16”--1/8” Fig. 14 15.
16. Apply silicone sealant between the tray or threshold and the pivot bracket. Also, apply silicone between the wall and the wall profiles. See Fig. 16 for details. Fig. 16 “ELEGANCE” Ver.4 Rev.
Style “B”: Stationary Glass Assembly and Installation NOTE: Use parts from Diagram “B” and “C” for the Stationary Glass assembly and installation. 17. Apply clear silicone along the inner channel of the Glass profile (04) and push the Stationary glass (21) inside the channel. NOTE: If you have difficulty sliding the Glass profile over the Stationary glass, you can slightly tap on the Glass profile with a rubber mallet and a piece of wood. Please do not strike directly on the profile.
19. Draw a line along the inner edge of the Wall profile (05) on the wall. Detach the Wall profile from the Stationary glass (21) and the Glass profile (04) assembly. Place the Wall profile to the outlined position and mark the drilling holes through the predrilled holes in the Wall profile. Now drill the holes using Ø 5/16” drill bit in the wall. 1 See Fig. 19 for details. 2 3 Ø5/16” Fig. 19 20.
21. Adjust the Stationary glass (21) position to ensure that when the Glass door (03) is closed, there is a gap (1/16”-1/8”) between the two glass panels. To adjust and secure the Stationary glass in place, install the Bottom Bracket (27) to the Stationary glass. Mark the drilling hole for the bracket. Make sure the mark is clear and visible and drill the hole using Ø1/8” drill bit. Use the Round head screws ST4.2×35 (25) to attach the Bottom Bracket to the shower base or the threshold.
23. Apply silicone sealant between the tray or threshold and the pivot bracket. Also, apply silicone between the wall and the wall profiles. See Fig. 23 and Fig. 24 for details. Fig. 23 NOTE: If you need to install the door on the right wall, simply exchange the position of the wall profile for glass door (01) and the wall profile (05). Fig. 24 “ELEGANCE” Ver.4 Rev.
Style “B” and “D”: Stationary Glass Assembly and Installation NOTE: Use parts from Diagram “B” or “C” (depends on your model style) for the Stationary Glass assembly and installation. Glass shelves installation 24. Mark the Glass shelf (22) position on the wall. According to the measurements in Fig. 25.1, mark the drilling holes on the wall for the Shelf brackets (31). Drill the holes using Ø 5/16” drill bit and insert the Wall anchors (23).
Style “C” and “D”: Shower Enclosure Assembly and Installation NOTE: Use parts from Diagram “A” and Diagram “B” or “C” (depends on your model style) for the Shower Enclosure assembly and installation. Style C 25. Please draw the vertical lines on the wall for the Glass door A and the Return panel B according to the size of your model in the size table below. Style D W2 W1 A B See Fig. 27 for details.
26. Apply clear silicone along the inner channel of the Glass profile (04) and push the Stationary glass (21) inside the channel. NOTE: If you have difficulty sliding the Glass profile over the Stationary glass, you can slightly tap on the Glass profile with a rubber mallet and a piece of wood. Please do not strike directly on the profile. 1 2 See Fig. 28 for details. 3 Fig 28 27. Place the Wall profile for glass door (01) on the shower base or the threshold vertically against the finished wall.
28. Push the Pivot retainers (08) into both ends of the Wall profile for glass door (01). 1 3 2 4 See fig. 30 for details. Fig 30 29. Run a silicone bead along the holes on the wall. Attach the Wall profile for glass door (01) and Pivot retainer (08) to the wall using Big flat head screws ST4.2×40 (16). 1 2 See fig. 31 for details. 3 Fig 31 “ELEGANCE” Ver.4 Rev.
30. Attach the Pivot assembly (07) to the top and the bottom ends of the Glass profile for glass door (02) with the Flat head screws ST4.2×25 (15) and M4×16 bolt (13). 1 See Fig. 32 for details. NOTE: The Back plate (K) of the Pivot assembly should face inside of your shower. 2 3 Fig 32 31.
NOTICE: The Glass door has 2 cuts for the Pivot assemblies. The deeper cut must be on the top. 32. Remove the Bolts (L) and Back plates (K) from the upper and bottom Pivot assemblies (07). Place the Glass door (03) to the Pivot assemblies, attach Back plates (K) to its position and fasten tight the Bolts. Make sure the clear rubber Spacers (J) are in between the glass and the metal parts. Secure tide the Glass door to the Pivot assemblies. 1 5 2 6 3 7 4 8 See fig. 34 for details. Fig 34 33.
34. Press the Anti-water strip (29) onto the vertical edge of the Stationary glass (21). Carefully butt the Stationary glass up against the wall vertically according to the measurements in size table. While securely holding the Stationary glass, close the Glass Door (03) and align the Stationary glass to it. If needed, adjust the position of the Stationary glass to make sure the Anti-Water strip makes tight contact to the Glass Door from top to bottom.
Fig 38 36. Push the Anti-water strip (10) into the vertical groove of the Glass profile for glass door (02). Attach the Bottom anti-water strip (11) onto the glass door. (You can cut the strips to size by using a knife). 1 4 2 5 See Fig. 39 for details. 3 Fig 39 “ELEGANCE” Ver.4 Rev.
37. Adjust the width of the opening section of the Glass door (03) by loosen the holding screws on the Pivot assemblies (07). Level the Glass door and the Stationary glass (21) position to ensure the Glass door has a tight contact to the flange of the Antiwater strip (10) from top to bottom. Install the Bracket (27) onto the Stationary glass and drill the hole using Ø 1/8” drill bit. Use the Round head screws ST4.2×25 (25) to attach Bracket to the shower base or the threshold.
39. Do the final adjustment if necessary. Make sure the Glass door (03) closes tight to the Anti-Water strip (29). See fig. 42 for details. Fig 42 40. After final adjustments of the Assembled unit drill the holes in the Glass profiles (02) and (04) through predrilled holes in the Wall profiles (01) and (05) using Ø 1/8” drill bit. 1 4 Ø1/8” Ø1/8” NOTE: You only need to drill through the first layer of the Glass Profile. Use the Round head screws ST4.
41. Apply silicone sealant between the tray or threshold, the stationary glass and the accessory. Also, apply silicone between the wall and the wall profiles. See fig. 44 for details. Caulk Fig 44 “ELEGANCE” Ver.4 Rev.
Style “C”: Support Bar Assembly and Installation NOTE: Use parts from Diagram “C” for the Support Bar assembly and installation. 42. Locate the Support bar (22). Adjust the bar to a proper position on the glass and the wall. Level it horizontally. Hold it firmly and outline the bracket’s position on the wall. Remove the Support bar and detach the wall bracket from it. Place the wall bracket against its outlined position on the wall and mark the drilling hole.
Style “D”: Glass Shelves Assembly and Installation NOTE: Use parts from Diagram “B” for the Glass Shelves assembly and installation. 43. Mark the Glass shelf (22) position on the wall. According to the measurements in Fig. 46.1, mark the drilling holes for the Shelf brackets (without nut) (31). Drill the holes using Ø 5/16” drill bit and insert the Wall anchors (23). Attach the Shelf brackets (without nut) to the wall using the Countersunk screw ST4.
Maintenance To insure long lasting life for your acrylic back walls, wipe them off after each use with a soft cloth. To clean the acrylic back walls use non-abrasive sprays or cream based cleaners. Never use abrasive cleansers, metal brushes or scrapers that could scratch or dull the surface. To insure long lasting life for your glass shower products, wipe them off after each use with a soft cloth. Rinse and wipe of the glass using either soft cloth or squeegee to prevent soap buildup.
DREAMLINE™ EXCLUSIVE LIMITED WARRANTY AS OF MAY 6, 2013 This warranty extends only to the original owner/end‐user for household use only and is not transferable to a subsequent owner. This warranty extends for a designated period of time, so long as it remains in use in its original place of installation. This warranty applies only to DreamLine products purchased from an authorized dealer in United States or Canada.
TEL: 866-731-2244 FAX: 866-227-1533 WWW.BATHAUTHORITY.COM For more information on DreamLineTM Shower Doors and Enclosure please visit www.BathAuthority.