UNIDOOR PLUS SHOWER DOOR GLASS PANEL INSTALLATION INSTRUCTIONS IMPORTANT DreamLineTM reserves the right to alter, modify or redesign products at any time without prior notice. For the latest up-to-date technical drawings, manuals or any other details please refer to the support.BathAuthority.com web page. Style F ATTENTION: This model features the half etched glass option. Please see specific installation instructions on page 12 when applicable. Please read these instructions carefully before installing.
Preparation 1. After opening all boxes and packages, read this introduction carefully. Check that all of the needed parts are included in the package by marking all the components on the “Detailed Diagram of Glass Panel Components”. Examine boxes and packages for shipping damage. If the unit has been damaged, has a finishing defect, or has missing parts, please contact our customer support department within 5 business days of the delivery date.
Detailed Diagram of Glass Panel Components 9 11 13 23 19 20 29 Packing List 09 11 13 19 U-channel 1 (76”, wall profile) Stationary glass Ø5/16” Wall anchor Anti-Water strip (door) 1pc 20 1pc 23 14pcs 29 1pc Anti-Water strip (Enclosure) Countersunk screw ST4.2x40 U-channel 2 (40”, bottom profile) 1pc* 14pcs 1pc NOTE: Unpack your unit carefully and inspect it. Lay it out and identify all parts using the detailed diagram and packing list in your manual as a reference.
Style “F”: 6”-34” In-Line Stationary Panel Installation NOTE: The Unidoor shower door needs to be installed prior to proceeding with the following Stationary Glass installation instructions. Please see the Single Shower Door installation manual included in the door packaging for complete shower door installation instructions. Before you begin the installation, please recheck your shower opening size. Specific size information can be found on our website at www.BathAuthority.com.
NOTE: Use parts from “Detailed Diagram of Glass Panel Components” for the Stationary Glass assembly and installation. 2. Measure the width of your stationary glass panel. NOTE: You will be doing straight cuts for this stationary panel installation. *It may be necessary to remove any burrs from the cut end of the U-channels with a metal file before placing the Uchannel on the glass. H Use a miter saw to rough cut the Uchannel 2 (40”, bottom profile) (29) to the actual width of the glass (+) 1”. See Fig.
3. Slip the U-channel 2 (40”, bottom profile) (29) and U-channel 1 (76”, wall profile) (09) onto the Stationary glass (11) in the shown locations. With the door open place the Stationary glass on threshold opposite of door. Adjust the Stationary glass and U-channel 1 (wall profile) against the wall to compensate for any out of plumb conditions ensuring that the Stationary glass is level vertically and U-channel 1 is flush with the wall.
5. Remove the U-channel 1 (76”, wall profile) (09), U-channel 2 (40”, bottom profile) (29) and Anti-Water strip (Door) (19) from the Stationary glass (11) and set the Stationary glass aside. Place the U-Channel 2 (bottom profile) onto the threshold base in line with the inside threshold mark. Mark the drill holes on the threshold through the predrilled holes in the UChannel 2 and drill the holes using Ø1/8” drill bit.
6. Cut the U-channel 1 (76”, wall profile) (09) at the top mark that was made in step #4. 1 Place the U-Channel 1 (wall profile) on the U-Channel 2 (40”, bottom profile) (29) and align vertically with wall mark. U-Channel 1 2 U-Channel 2 3 Mark the drill holes on the wall through the predrilled holes in the U-Channel 1. Now drill holes in the wall using Ø5/16 drill bit and insert the Ø5/16” Wall anchors (13). 4 Ø5/16” 5 See Fig. 8 for details. Fig. 8 7.
Fig. 10 8. Slide the Stationary glass (11) into the groove of both U-Channels. NOTE: If you have difficulty sliding the Stationary glass into the U-Channels, you can slightly tap on the Stationary glass with a rubber mallet and a piece of wood. 1 2 3 4 Apply a bead of silicone on both open ends of the U-Channels, and its connection. See fig. 11 for details. Fig. 11 UNIDOOR PLUS, IN-LINE PANEL FULL Ver.
9. Apply waterproof silicone along the connection of both U-Channels to the wall and threshold on the inside of shower. See Fig. 12 for details. waterproof silicone inside Fig. 12 10. Notch the Anti-Water strip (Door) (19) 1” at the base to fit around bottom Uchannel. Press the Anti-Water strip (Door) (19) onto the vertical edge of the Stationary glass (11). 2 1 inside outside See Fig. 13 for details. 3 4 inside inside outside outside Fig. 13 UNIDOOR PLUS, IN-LINE PANEL FULL Ver.
Maintenance To ensure long lasting life for your acrylic back walls, wipe them off after each use with a soft cloth. To clean the acrylic back walls use non-abrasive sprays or cream based cleaners. Never use abrasive cleansers, metal brushes or scrapers that could scratch or dull the surface. To ensure long lasting life for your glass shower products, wipe them off after each use with a soft cloth. Rinse and wipe of the glass using either soft cloth or squeegee to prevent soap buildup.
Style “F”: Half Etched Glass Installation NOTE: This model features the half etched glass option. Hinged Left installation shown. To install for hinged Right, flip the door to the proper handing. -The textured surface of both the stationary glass and glass door should face out. See Fig. 14 for details. Fig. 14 UNIDOOR PLUS, IN-LINE PANEL FULL Ver.
DREAMLINE™ EXCLUSIVE LIMITED WARRANTY AS OF MAY 6, 2013 This warranty extends only to the original owner/end‐user for household use only and is not transferable to a subsequent owner. This warranty extends for a designated period of time, so long as it remains in use in its original place of installation. This warranty applies only to DreamLine products purchased from an authorized dealer in United States or Canada.
TEL: 866-731-2244 FAX: 866-227-1533 WWW.BATHAUTHORITY.COM For more information on DreamLineTM Shower Doors and Enclosure please visit www.BathAuthority.com UNIDOOR PLUS, IN-LINE PANEL FULL Ver.