UNIDOORLUX SHOWER DOOR INSTALLATION INSTRUCTIONS IMPORTANT! DreamLineTM reserves the right to alter, modify or redesign products at any time without prior notice. For the latest up-to-date technical drawings, manuals or any other details please refer to the support.BathAuthority.com web page. Please read these instructions carefully before installing.
Preparation 1. After opening all boxes and packages, read this introduction carefully. Check that all of the needed parts are included in the package by marking all the components on the “Detailed Diagram of Shower Door Components”. Examine boxes and packages for shipping damage. If the unit has been damaged, has a finishing defect, or has missing parts, please contact our customer support department within 5 business days of the delivery date.
Detailed Diagrams of Shower Door Components Diagram A Diagram B 4 12 1 11 31 13 15 5 16 17 2 18 6 19 7 20 24 8 *ATTENTION: All parts that marked with the star (*), not provided with 6” Stationary panel.
Shower Door Installation 1. Attach the Hinges (05) to the Glass door (01) using at least one (2mm) vinyl hinge gasket per side. 1 See Fig. 1 for details. ATTENTION: Never set your glass down directly onto a tile or concrete floor. Always use a piece of wood or cardboard and leave the corner pads on the glass until it becomes necessary to remove them to protect the bottom edge and corners from damage which could lead to breakage. outside 2 inside Fig. 1 2.
3. Hold the door in place and mark the drill holes for both Hinges (05) on the wall. Set the door aside and drill the holes in the wall using Ø 1/4” drill bit. IMPORTANT: The included PVC hinge spacers (31) are provided to compensate for out of plumb wall conditions. Use only as needed as their use could compromise the opening size of your shower. Please see Fig 4 for an installation example.
ATTENTION The back plate of the hinge from inside the shower locates too close to the drilled holes in the wall and might get scratched with the long screws or screwdriver. (OPTIONAL) 4. Carefully remove back plates from the Hinges (05) and set the Glass door (01) aside. Screw in the rest of the Countersunk screws ST5 x 70 (04) into the wall, place the Glass door back to its position and reassemble the Hinges. 1 3 inside inside 2 4 inside See Fig. 5 and Fig. 6 for details. Fig. 5 5.
6. Mount the two Wall bracket (24) through the notches on the Stationary glass (11). Press the Anti-water strip (19) onto the vertical edge of the Stationary glass. 1 2 outside outside See Fig. 7 for details. 3 inside 4 2 inside outside outside 3 Fig. 7 outside 7. Carefully butt the Stationary glass (11) up against the wall vertically. See Fig. 8 for details. inside Fig.8 “UNIDOORLUX” Rev.3 Ver.
. While securely holding the Stationary glass (11), close the Glass Door (01) and align the Stationary glass to it. If needed, adjust the position of the Stationary glass to make sure the AntiWater strip (19) makes tight contact to the Glass Door from top to bottom. Outline the position of the Wall brackets (24) on the wall from inside the shower. outside 1 inside outside 2 inside 3 inside See Fig. 9 for details.
10. Place Stationary Glass (11) back into position and tighten it up to the Wall Bracket (24). 1 outside outside See Fig. 11 for details. inside 2 inside 3 inside Fig. 11 11. To adjust and secure the Stationary Glass (11) in place, install the Bottom Bracket (18) to the Stationary glass; Drill the hole into the shower base or the threshold through oval notched hole in the Bottom bracket using Ø 1/8” drill bit. Use the Round head screws ST4.
ATTENTION: If width of the Stationary glass (11) is 12” and over, Support bar (12) must be installed for stability. 1 2 3 4 inside 12. Locate the Support bar* (12). Adjust the Support bar* to a proper position on the Stationary glass (11) and the wall. Level it horizontally. Hold it firmly and outline the bracket’s position on the wall. Remove the Support bar* and detach the wall bracket from it. Place the bracket against its outlined position on the wall and mark the drilling hole.
14. Measure the bottom of the Glass door (01) from the Side strip (06) to the vertical edge on the Handle (02) side. Cut the Bottom antiwater strip (07) to the size of your measurement and notch 3/8” of the inner side of the Bottom antiwater strip. Handle side strip end 3/8" 1 2 inside inside outside outside NOTICE: Make sure the Handle side of the Glass door tight to the Antiwater strip (07) along the vertical edge when the door is shut. 3 4 inside See Fig. 15 for details.
Maintenance To insure long lasting life for your acrylic back walls, wipe them off after each use with a soft cloth. To clean the acrylic back walls use non-abrasive sprays or cream based cleaners. Never use abrasive cleansers, metal brushes or scrapers that could scratch or dull the surface. To insure long lasting life for your glass shower products, wipe them off after each use with a soft cloth. Rinse and wipe of the glass using either soft cloth or squeegee to prevent soap buildup.
DREAMLINE™ EXCLUSIVE LIMITED WARRANTY AS OF MAY 6, 2013 This warranty extends only to the original owner/end‐user for household use only and is not transferable to a subsequent owner. This warranty extends for a designated period of time, so long as it remains in use in its original place of installation. This warranty applies only to DreamLine products purchased from an authorized dealer in United States or Canada.
TEL: 866-731-2244 FAX: 866-227-1533 WWW.BATHAUTHORITY.COM For more information on DreamLineTM Shower Doors please visit www.BathAuthority.com “UNIDOORLUX” Rev.3 Ver.