UNIDOOR/UNIDOORLUX/UNIDOOR PLUS SINGLE SHOWER DOOR INSTALLATION INSTRUCTIONS IMPORTANT DreamLine® reserves the right to alter, modify or redesign products at any time without prior notice. For the latest up-to-date technical drawings, manuals, warranty information or additional details please refer to your model’s web page on DreamLine.
Style “A”: Half Frosted Band Glass Installation NOTE: This model features the Half Frosted Band glass option. Hinged Left installation shown. To install for hinged Right, flip the door to the proper handing. NOTE: The textured surface on the door glass should face outside of the shower. Hinged Left installation Hinged Right installation 2 UNIDOOR Single Shower Door manual Ver.2 Rev.
UNIDOOR STYLES Models with Glass-to-Wall hinges Style A Style B Style E Style I Style C Style F Style J Style D Style G Style L 3 UNIDOOR Single Shower Door manual Ver.2 Rev.
Models with Glass-to-Glass hinge panels: For Glass to Glass hinge Door installation use the installation manual packaged with the Hinge panel glass 4 UNIDOOR Single Shower Door manual Ver.2 Rev.
STYLE A UNIDOOR Single shower door 23”- 30” Refer to detailed diagram on page 5 of this manual for assembly instructions STYLE B * UNIDOOR Shower door 23” – 30” with 6” small or 12”-30” large stationary panel STYLE C * UNIDOOR Shower door with 12”-30” large stationary panel STYLE D * UNIDOOR LUX Shower door with 6” small or 14”-30” large stationary panel STYLE E * UNIDOOR LUX Shower enclosure with 30” return stationary panel STYLE F * UNIDOOR PLUS Shower door with 6”-34” in-line stationary panel secured usi
with 12”, 18”, 24” or 26” inline buttress panel secured using u-channel STYLE M3 *^ UNIDOOR X Shower door 23”~30” with 6” or 24” hinge panel, with 6”, 6-1/2”, 14”, 14-1/2”, 22” or 22-1/2” full height inline panel and 30” - 34” full height return panel secured using u-channel STYLE M4 *^ UNIDOOR X Shower door 23”~30” with 6” or 24” hinge panel, with 12”, 18”, 24” or 26” in-line buttress panel and 30”- 40” buttress return panel secured using u-channel * For the panel installation instructions, please refer t
Preparation 1. Prior to installation, examine all boxes and packages for shipping damage and compare the piece count with your packing slip. After opening all boxes and packages read this introduction carefully. Check that all of the needed parts are included in the package by checking off the components on the “Detailed Diagram of Shower Door Components”.
Tools Required 8 UNIDOOR Single Shower Door manual Ver.2 Rev.
UNIDOOR Single Shower Door manual Ver.2 Rev.
UNIDOOR Single Shower Door manual Ver.2 Rev.
UNIDOOR Single Shower Door manual Ver.2 Rev.
Detailed Diagram of Shower Door Components 4 1 31 5 2 6 The glass surface with the ClearMax™ label must be installed to face inside of the shower 7 8 Packing List Part# 01 02 04 05 Description Door glass Handle Countersunk screw ST5×70 Hinge with Adjustable angle Qty 1pc 1pc 8pcs 2pcs Part# 06 07 08 31 Description Side strip ( 3 sections to cut) Bottom anti-water strip L-shaped strip PVC hinge spacer Qty 1pc 1pc 1pc 4pcs NOTE: Unpack your unit carefully and inspect it.
Single Shower Door Assembly and Installation NOTE: The following shower door installation instructions should be used as a general guide and prerequisite to the installation of the UNIDOOR, UNIDOORLUX and UNIDOOR PLUS models. Before you begin the installation, please check your finished opening size. Specific size information can be found on our website at DreamLine.
2. The Door Glass (01) ships with four 5/8” shims attached to the top (2pcs) and bottom (2pcs). Determine the swing of your door and only remove the shims from the top of the door glass, leaving the bottom shims in place. Set the Door Glass (01) onto the threshold at the desired location and check for level. These 5/8” shims will leave the proper spacing at the bottom of the door glass and will ensure that the door height finishes at 72”, but always confirm with a measurement.
1 TIP: The PVC hinge spacer can also be used as a template to assist with marking the hinge mounting holes. 2 3 Fig. 4 ATTENTION: The back plate of the hinge from inside the shower locates too close to the drilled holes in the wall and might get scratched by the long screws or screwdriver. Be careful not to scratch the hinge surface. (OPTIONAL) 4. Carefully remove back plates from the Hinges (05) and set the Door Glass (01) aside.
Setting the Adjustable Hinges The Adjustable hinges are pre-set to overclose to 85º and are adjustable up to 90º after the door is installed. Once the door glass is installed, simply loosen the allen set screws and position the door to the desired closed position. While holding the door in the new closed position, retighten the allen screws and your door will now self-center to the chosen closed position. 4a.
4b. The hinges are factory set to 85 degrees. You can change this angle by using the adjustment screws on the hinge plate. (Figure 5b) inside outside Figure 5b 4c. Use the supplied Allen Key to loosen the adjustment screws on the inside hinge plate, adjust the door to the desired angle (90 degrees for example) then retighten the adjustment screws (Figure 5c). Be sure that you create a tight seal with the supplied strike vinyl when the door is in the closed position.
5. Mount the Handle (02) to the Door Glass (01). See Fig. 6 for details. NOTE: DO NOT attach the handle to the door glass until instructed to do so. DO NOT use the handle to lift the glass during installation. This may result in damage to the glass and/or serious injury. Always use an assistant or a professional grade glass suction cup when handling the door glass. Fig. 6 6. Measure the bottom of the Door Glass (01) from end to end to determine the actual width of the door.
1 Into the hinge Into the hinge 3 4 7/8" 7/8" Into the hinge 5 See Fig. 8 for details 2 7/8" 7. Get three measurements: from the top edge of the Door Glass (01) to the upper body of the top Hinge (05) (+) 7/8” from the lower body of the upper Hinge to the upper body of the bottom Hinge (+) 1-3/4” from the lower body of the bottom Hinge to top of the installed Bottom anti-water strip (07) (+) 1-7/8” Cut the Side strip (06) according to the measurements.
Fig. 10 20 UNIDOOR Single Shower Door manual Ver.2 Rev.
Product Maintenance BASES and BACKWALLS: To ensure long lasting life for your acrylic back walls: wipe them off after each use with a soft cloth. To clean the acrylic back walls use non-abrasive sprays or cream based cleaners. Avoid the use of aerosol spray cleaners. Never use abrasive cleansers, metal brushes or scrapers that could scratch or dull the surface. GLASS: To ensure long lasting life for your glass shower products: wipe them off after each use with a soft cloth.
TEL: 866-731-2244 FAX: 866-857-3638 DREAMLINE.COM For more information on DreamLine® Shower Doors and Enclosures please visit DreamLine.com 22 UNIDOOR Single Shower Door manual Ver.2 Rev.