Enigma-X Shower Door & Base Kit SHOWER Door AND SHOWER BASE KIT INSTALLATION INSTRUCTIONS IMPORTANT DreamLineTM reserves the right to alter, modify or redesign products at any time without prior notice. For the latest up-to-date technical drawings, manuals or any other details please refer to the support.BathAuthority.com web page.
ENIGMA-X SHOWER DOOR & TUB DOOR INSTALLATION INSTRUCTIONS IMPORTANT DreamLineTM reserves the right to alter, modify or redesign products at any time without prior notice. For the latest up-to-date technical drawings, manuals or any other details please refer to the support.BathAuthority.com web page. Please read these instructions carefully before installing.
Preparation 1. After opening all boxes and packages, read this introduction carefully. Check that all of the needed parts are included in the package by marking all the components on the “Detailed Diagram of Shower Door Components”. Examine boxes and packages for shipping damage. If the unit has been damaged, has a finishing defect, or is missing parts, please contact our customer support department within 5 business days of the delivery date.
Detailed Diagram of Shower Door Components Packing List 01 02 03 04 05 06 07 08 09a 09b 10 Door stopper Stationary glass Upper guide rail Roller Glass door Handle Glass bracket Guide rail bracket Wall anchor Ø 3/8” Wall anchor Ø5/16” Round head screw ST6×45 2pcs 1pc 1pc 2pcs 1pc 1pc 2pcs 2pcs 2pcs 1pcs 2pcs 11 12 13 14 15 16 17 18 19 20 Hex wrench 3mm, 4mm, 5mm Guide block (with plugs) Bumper strip Anti-water strip Anti-splash threshold Threshold bracket (with plug) Round head screw ST4.
Shower Door Installation 1. Measure the distance between two finished walls. This distance is marked as “W”. See Fig. 1 for details. W Fig. 1 2. Your Upper Guide rail (03) has been precut for your Shower model opening width: 48” or 60” for shower width. If W-width of your wall-to-wall opening is equal to the size of your Shower model, it is unnecessary to cut the Upper Guide rail and you can continue to Step 3.
3. Install the Upper guide rail (03) to the Stationary glass (02) with the Glass brackets (07) and tighten the set screws. Slide the Door stoppers (01) on each end of the Upper guide rail and secure them temporarily. Slide the Guide Rail brackets (08) on each end of the Upper guide rail and temporarily secure them as well. Assemble the Wall Bracket (19) onto the bottom corner of the Stationary glass (02). 1 4 2 5 3 6 See Fig. 3 and Fig. 4 for details. Fig.
4. Place the Stationary glass (02) on the preinstalled shower base or threshold and butt it up against the wall. A (Please note that the Guide rail (03) secured on the Stationary Glass should face inside the shower). Make sure the Stationary glass and the Guide rail are leveled and aligned with the shower base or threshold. If a horizontal adjustment is required, adjust it in the Glass brackets (07). B See Fig. 5 for details. Fig. 5 5.
6. Drill the holes for the Wall bracket (19) using Ø 5/16 drill bit and insert the Wall anchors (9b). Drill the holes for the Rail brackets (08) using Ø 3/8” drill bit and insert the Wall anchors (9a). 1 2 Ø5/16" See Fig. 7 for details. 3 4 Ø 3/8" 5 Ø 3/8" 6 Fig. 7 7. Fasten the Wall bracket (19) to the wall using the Round head screw ST4.2×30 (18). Mount the male parts of the Rail brackets onto both walls using the Round head screw ST6×45 (10). 1 See Fig. 8 for details. 2 3 Fig.
8. Place the Guide Block (12) on the shower base or the threshold and place the Stationary glass (02) back in to the designated position so it gets in the groove of the Guide block. 1 See Fig. 9 for details. 2 Fig. 9 9. Fasten both female parts of the Guide rail brackets (08) to their male parts on the walls. Tighten the set screws on the Guide rail brackets to secure the Upper guide rail (03) between the two walls.
. Upper guide rail (03) must be leveled horizontally. Adjust Guide rail bracket (08) using hex key on both end if it necessary to level the Upper guide rail. Tighten the screws from top and bottom of the Guide rail bracket. 1 See Fig. 11 and Fig. 12 for details 2 Fig. 11 Fig. 12 “Enigma-X” Rev.2 Ver.
. Parallel the Stationary glass (02) to the shower base or threshold. Measure the distance from the side wall to the far edge of the Guide block (12). This distance will be “X”. Cut the Anti-splash threshold (15) to the size of 1 4 2 5 3 6 X X−½”. Insert one side of the Anti-splash threshold fully into the Guide block and cover the other side with the Threshold bracket (16).
13. Attach two Rollers (04) to the Glass door (05). Suspend the door by hanging the Rollers onto the Upper guide rail (03) and slide the bottom edge of the Glass door into the groove of the Guide block (12). Adjust the fasteners on both Rollers to ensure that the bottom edge of the Glass door does not touch the bottom of the Guide block. Then mount two Roller guards (20) on the door to secure the door to the Upper guide rail. 1 4 See Fig. 15 for details. 2 5 3 6 Fig. 15 14.
15. Apply Kitchen & Bath silicone at both ends of the Anti-splash threshold (15), around the Guide block (12) and around the Threshold bracket (16). 1 See Fig. 17 for details. Silicone 2 Silicone Fig. 17 16. Apply Kitchen & Bath silicone along the connection of the Stationary glass with the wall and the shower base or the threshold. See Fig. 18 for details. Fig. 18 “Enigma-X” Rev.2 Ver.
Product Maintenance To ensure long lasting life for your acrylic back walls, wipe them off after each use with a soft cloth. To clean the acrylic back walls use non-abrasive sprays or cream based cleaners. Never use abrasive cleansers, metal brushes or scrapers that could scratch or dull the surface. To ensure long lasting life for your glass shower products, wipe them off after each use with a soft cloth. Rinse and wipe off the glass using either soft cloth or squeegee to prevent soap buildup.
SLIMLINE SHOWER BASE SHOWER BASE DIMENSIONS AND INSTALLATION INSTRUCTIONS IMPORTANT DreamLineTM reserves the right to alter, modify or redesign products at any time without prior notice. For the latest up-to-date technical drawings, manuals or any other details please refer to your model’s web page on BathAuthority.com Please read these instructions carefully before installing.
Preparation 1. Prior to installation, examine all boxes and packages for shipping damage and compare the piece count with your packing slip. After opening all boxes and packages, read this introduction carefully. Check that all of the needed parts are included in the package by checking off the components on the “Detailed Diagram of Shower Door Components”.
SINGLE THRESHOLD SHOWER BASE Center Drain Configuration W W1 11 D1 D MODEL SPECIFICATION D (in) W (in) D1 (in) W1 (in) DLT-1132320 DLT-1136360 32"×32" 36"×36" 32" 36" 32" 36" 15" 15" 16" 18" DLT-1134420 34” x 42” 34” 42” 15” 21” DLT-1132480 DLT-1136480 DLT-1130600 DLT-1132600 DLT-1134600 DLT-1136600 32"×48" 36"×48" 30"×60" 32"×60" 34"×60" 36"×60" 32” 36" 30" 32" 34" 36" 48” 48" 60" 60" 60" 60" 15” 15" 15" 15" 15" 15" 24” 24" 30" 30" 30" 30" “SLIMLINE SHOWER BASE” Ver.5 Rev.
SINGLE THRESHOLD SHOWER BASE Left-Hand Drain Configuration W W1 D1 D MODEL SPECIFICATION D (in) W (in) D1 (in) W1 (in) DLT-1130601 DLT-1132601 DLT-1134601 DLT-1136601 30"×60" 32"×60" 34"×60" 36"×60" 30" 32" 34" 36" 60" 60" 60" 60" 15" 15" 17" 18" 12" 12" 12" 12" “SLIMLINE SHOWER BASE” Ver.5 Rev.
SINGLE THRESHOLD SHOWER BASE Right-Hand Drain Configuration W W1 D1 D MODEL SPECIFICATION D (in) W (in) D1 (in) W1 (in) DLT-1130602 DLT-1132602 DLT-1134602 DLT-1136602 30"×60" 32"×60" 34"×60" 36"×60" 30" 32" 34" 36" 60" 60" 60" 60" 15" 15" 17" 18" 12" 12" 12" 12" “SLIMLINE SHOWER BASE” Ver.5 Rev.
NEO ANGLE SHOWER BASE W C C A W B A MODEL SPECIFICATION W (in) A (in) B (in) C (in) DLT-2036360 DLT-2038380 DLT-2040400 DLT-2042420 36"×36" 38"×38" 40"×40" 42"×42" 36" 38" 40" 42" 18 5/16" 20 5/16" 22 5/16" 24 5/16" 25" 25" 25" 25" 12" 12" 14 3/8" 14 3/8" “SLIMLINE SHOWER BASE” Ver.5 Rev.
QUARTER ROUND SHOWER BASE W C C W R MODEL SPECIFICATION W (in) C (in) R (in) DLT-7033330 DLT-7036360 DLT-7038380 33"×33" 36"×36" 38"×38" 33" 36" 38" 12" 12" 12" 21 5/8" 21 5/8" 21 5/8" “SLIMLINE SHOWER BASE” Ver.5 Rev.
DOUBLE THRESHOLD SHOWER BASE Corner Drain Configuration W C C W MODEL SPECIFICATION W (in) C (in) DLT-1032320 DLT-1036360 32"×32" 36"×36" 32" 36" 12" 12" “SLIMLINE SHOWER BASE” Ver.5 Rev.
DOUBLE THRESHOLD SHOWER BASE Left-Hand Drain Configuration W W1 D1 D MODEL SPECIFICATION D (in) W (in) D1 (in) W1 (in) DLT-1034481 DLT-1036481 DLT-1036601 34"×48" 36"×48" 36"×60" 34" 36" 36" 48" 48" 60" 17" 18" 18" 12" 12" 12" “SLIMLINE SHOWER BASE” Ver.5 Rev.
DOUBLE THRESHOLD SHOWER BASE Right-Hand Drain Configuration W W1 D1 D MODEL SPECIFICATION D (in) W (in) D1 (in) W1 (in) DLT-1034482 DLT-1036482 DLT-1036602 34"×48" 36"×48" 36"×60" 34" 36" 36" 48" 48" 60" 17" 18" 18" 12" 12" 12" “SLIMLINE SHOWER BASE” Ver.5 Rev.
Shower Base Cross Section Diagram Shower Base Cement board Finished Wall (2"×4") Stud Mortar Drain “SLIMLINE SHOWER BASE” Ver.5 Rev.
Shower Base Installation - Preparation 1. Ensure that the floor and the studs are at right angles. Provide a 5”×5” opening in the subfloor for the drain. The 2” PVC waste pipe should extend above the surface of the sub-floor according to the drain installation instructions and the height of the Shower base. Refer to the product drawings and tables in these installation instructions for the drain location. 90° 90° 90° See Fig. 1 and Fig. 2 for details.
2. Install the shower drain (NOT INCLUDED) according to the drain installation manual (supplied with the drain). See Fig. 3 for example Fig. 3 3. Place the tray into the designated position so that the Drain Body drops around the Drain Pipe and butt the Shower Base up against the studs. See Fig. 4 for details. Lower the base over the drain pipe and set it into place against the studs. Fig. 4 “SLIMLINE SHOWER BASE” Ver.5 Rev.
4. Level the tray and place marks on the studs above the upper edge of the tile flange. See Fig. 5 for details. Level base in two directions Fig. 5 5. Mix the bedding material (Mortar, cement-sand mix, etc.) Concrete or plaster is not recommended. Apply enough bedding material to support the entire bottom of the shower base. This will add additional stability and prevent the base from shifting position. See Fig. 6 for details. Mortar Fig. 6 “SLIMLINE SHOWER BASE” Ver.5 Rev.
6. After the bedding material has been poured and before it sets, place the shower base into the position with the drain assembly sliding over the PVC waste pipe. It will be necessary to push the shower base until the top of the tile flange aligns with the marks drawn on the studs and the front edge is contacting the rough floor along the entire length of the shower base. Ensure that the base is level in all directions.
Fig. 9 Product maintenance To ensure long lasting life for your acrylic back walls, wipe them off after each use with a soft cloth. To clean the acrylic back walls use non-abrasive sprays or cream based cleaners. Never use abrasive cleansers, metal brushes or scrapers that could scratch or dull the surface. To ensure long lasting life for your glass shower products, wipe them off after each use with a soft cloth. Rinse and wipe of the glass using either soft cloth or squeegee to prevent soap buildup.
DREAMLINE™ EXCLUSIVE LIMITED WARRANTY AS OF MAY 6, 2013 This warranty extends only to the original owner/end‐user for household use only and is not transferable to a subsequent owner. This warranty extends for a designated period of time, so long as it remains in use in its original place of installation. This warranty applies only to DreamLine products purchased from an authorized dealer in United States or Canada.
TEL: 866-731-2244 FAX: 866-857-3638 WWW.BATHAUTHORITY.COM For more information on DreamLineTM Shower Bases please visit www.BathAuthority.