Aqua Fold Shower Door & Base SHOWER DOOR AND BASE INSTALLATION INSTRUCTIONS IMPORTANT DreamLine® reserves the right to alter, modify or redesign products at any time without prior notice. For the latest up-to-date technical drawings, manuals, warranty information or additional details please refer to your model’s web page on DreamLine.
©2018 DreamLine. All Rights Reserved SLIMLINE SHOWER BASE SHOWER BASE DIMENSIONS AND INSTALLATION INSTRUCTIONS IMPORTANT! DreamLine® reserves the right to alter, modify or redesign products at any time without prior notice. For the latest up-to-date technical drawings, manuals, warranty information or additional details please refer to your model’s web page on DreamLine.
©2018 DreamLine. All Rights Reserved Preparation 1. Prior to installation, examine all boxes and packages for shipping damage and compare the piece count with your packing slip. After opening all boxes and packages read this introduction carefully. Check that all of the needed parts are included in the package by checking off the components on the “Detailed Diagram of Shower Door Components”.
©2018 DreamLine.
©2018 DreamLine.
©2018 DreamLine.
©2018 DreamLine.
©2018 DreamLine.
©2018 DreamLine.
©2018 DreamLine.
©2018 DreamLine.
©2018 DreamLine.
©2018 DreamLine.
©2018 DreamLine.
©2018 DreamLine. All Rights Reserved Shower Base Installation - Preparation 1. Ensure that the floor and the studs are at right angles. Provide a 5”×5” opening in the subfloor for the drain. The 2” PVC waste pipe should extend above the surface of the sub-floor according to the drain installation instructions and the height of the Shower base. Refer to the product drawings and tables in this installation manual for the drain location. 90° 90° 90° See Fig. 1 and Fig. 2 for details.
©2018 DreamLine. All Rights Reserved 2. Install the shower drain (NOT INCLUDED) according to the drain installation manual (supplied with the drain). See Fig. 3 for example Fig. 3 3. Place the tray into the designated position so that the Drain cutout drops around the Drain Pipe and butt the Shower Base up against the studs. See Fig. 4 for details. Lower the base over the drain pipe and set it into place against the studs. Fig.
©2018 DreamLine. All Rights Reserved 4. Level the tray and place marks on the studs above the upper edge of the tile flange. See Fig. 5 for details. Level base in two directions Fig. 5 5. Mix the bedding material (Mortar, cement-sand mix, etc.) Concrete or plaster is not recommended. Apply enough bedding material to support the entire bottom of the shower base. This will add additional stability and prevent the base from shifting position. See Fig. 6 for details. Mortar Fig.
©2018 DreamLine. All Rights Reserved 6. After the bedding material has been poured and before it sets, place the shower base into the position with the drain assembly sliding over the PVC waste pipe. It will be necessary to push the shower base until the top of the tile flange aligns with the marks drawn on the studs and the front edge is contacting the rough floor along the entire length of the shower base. Ensure that the base is level in all directions.
©2018 DreamLine. All Rights Reserved Fig.
©2018 DreamLine. All Rights Reserved Product Maintenance BASES and BACKWALLS: To ensure long lasting life for your acrylic base and/or back walls: wipe them off after each use with a soft cloth. To clean the acrylic base or back walls use non-abrasive sprays or cream based cleaners. Avoid the use of aerosol spray cleaners. Never use abrasive cleansers, metal brushes or scrapers that could scratch or dull the surface.
TEL: 866-731-2244 FAX: 866-857-3638 DREAMLINE.COM For more information on DreamLine® Shower Doors and Enclosures please visit DreamLine.
AQUA FOLD SHOWER / TUB DOOR INSTALLATION INSTRUCTIONS IMPORTANT DreamLine® reserves the right to alter, modify or redesign products at any time without prior notice. For the latest up-to-date technical drawings, manuals, warranty information or additional details please refer to your model’s web page on DreamLine.com Model# SHDR-3630720-01 SHDR-3634720-01 Model# SHDR-3636580-01 Left hand installation shown ® For more information about DreamLine products please visit DreamLine.
Preparation 1. Prior to installation, examine all boxes and packages for shipping damage and compare the piece count with your packing slip. After opening all boxes and packages read this introduction carefully. Check that all of the needed parts are included in the package by checking off the components on the “Detailed Diagram of Shower Door Components”.
Tools Required Waterproof Silicone Tape Measure Level AQUA FOLD manual Ver 2 Rev 5 12/2016 Pencil Caulk Gun Phillips Screwdriver Electric Drill Drill bit (Ø=1/8") Hammer Drill bit (Ø=5/16") Knife 3
Detailed Diagrams of Shower Door Components Packing List 01 02 03 04 05 06 07 Wall profile Glass door 1 w/ Hinged glass profile Glass door 2 Hinge (with allen wrench) Wall anchor Big head screw ST4.2×40 Round head screw ST4.
Shower Door Installation NOTE: This model is reversible for left or right-hand installation. Left-hand installation is demonstrated in this manual. For right-hand installation, reverse the orientation of your product. 1. Prepare Glass door 1 (02) and Glass door 2 (03) to set the Hinges (04). See Fig. 1 for details. IMPORTANT! There is a top and a bottom to the assembled glass door rail. Top Fig. 1 2. First, attach the Hinges (04) to Glass door 1 (02), then attach Glass door 2 (03) to the Hinges (04).
Fig. 3 3. Remove the Wall Profile (01) from the Door Assembly. Place the Wall profile (01) onto the tub or threshold against the finished wall in the desired position. Use a level and adjust the Wall profile (01) to plumb. See Fig. 4 for details. Fig.
4. Mark the drill holes on the wall through the predrilled holes in the Wall profile (01). Now drill holes in the wall using a Ø5/16 drill bit and insert the Wall anchors (05). Apply silicone along the Wall profile (01) and around the holes. Fasten the Wall profile (01) to the wall with the Big head Screw ST4.2×40 (06). See Fig. 5 for details. 1 4 2 5 Ø5/16” 3 Fig. 5 5. Slide the assembled Glass door with Hinged glass profile (02) into the groove of the Wall profile (01) and level it vertically.
6. Snap the Aluminum threshold (10) into the Threshold connector (09) and Threshold end cover (13). (Left-hand installation shown) Run a bead of Waterproof silicone along the Aluminum threshold (10). Attach the Aluminum threshold (10) onto the tub deck, parallel to the tub edge with the Threshold connector (09) tight to the bottom of the Hinged glass profile (02). See Fig 4.4. Run a bead of Waterproof silicone along the connections of the Threshold connector (09) and Hinged glass profile (02).
8. Mount the Handle Knob (14) onto Glass door 2 (03). 1 WARNING: To avoid damage to the glass: Use caution when folding the doors to prevent the metal knob from contacting the glass surface. See Fig. 9 for details. 2 Fig. 9 9. Test the operation of the doors and adjust the hinges as necessary to make the door operate smoothly. See Fig. 10 for details. 10. Apply a high quality mildew-resistant silicone to the wall and threshold, along the inside edge of the wall profile and threshold.
Product Maintenance BASES and BACKWALLS: To ensure long lasting life for your acrylic back walls: wipe them off after each use with a soft cloth. To clean the acrylic back walls use non-abrasive sprays or cream based cleaners. Avoid the use of aerosol spray cleaners. Never use abrasive cleansers, metal brushes or scrapers that could scratch or dull the surface. GLASS: To ensure long lasting life for your glass shower products: wipe them off after each use with a soft cloth.
TEL: 866-731-2244 FAX: 866-857-3638 DREAMLINE.COM For more information on DreamLine® Shower Doors and Enclosures please visit DreamLine.