Allure Shower Door & Base Kit SHOWER Door AND SHOWER BASE KIT INSTALLATION INSTRUCTIONS IMPORTANT DreamLineTM reserves the right to alter, modify or redesign products at any time without prior notice. For the latest up-to-date technical drawings, manuals or any other details please refer to the support.BathAuthority.com web page.
ALLURE SHOWER DOOR INSTALLATION INSTRUCTIONS IMPORTANT DreamLineTM reserves the right to alter, modify or redesign products at any time without prior notice. For the latest up-to-date technical drawings, manuals or any other details please refer to the support.BathAuthority.com web page. Please read these instructions carefully before installing.
Preparation 1. After opening all boxes and packages, read this introduction carefully. Check that all of the needed parts are included in the package by marking all the components on the “Detailed Diagram of Shower Door Components”. Examine boxes and packages for shipping damage. If the unit has been damaged, has a finishing defect, or has missing parts, please contact our customer support department within 5 business days of the delivery date.
Detailed Diagrams of Shower Door Components Diagram A Diagram B Packing List A 01 02 03 04 05 06 07 08 09 10 11 12 Wall profile for small stationary glass Glass profile for small stationary glass Small stationary glass Glass door Glass profile Wall profile Handle Pivot retainer Pivot bracket(upper and bottom) Glass fixer(upper and bottom) Washer Pivot assembly(upper and bottom) 1pc 1pc 1pc 1pc 1pc 1pc 1pair 2pcs 1pair 1pair 2pcs 1pair 13 14 15 16 17 18 19 20 21 22 23 24 Fixing nut with M4×12 screw Soc
Shower Door Top View Diagram 15/16” “Allure” Rev.3 Ver.
Shower Door Installation 1. Place the Wall profile for small stationary glass (01) on the threshold vertically and align against the finished wall. Adjust the Wall profile for small stationary glass position and level it. Mark the drilling holes on the wall through the predrilled holes in the Wall profile for small stationary glass. Now drill the holes in the wall using Ø 5/16” drill bit and insert the Wall anchor (15). 1 2 See Fig. 1 for details. Ø5/16” 3 Fig. 1 2.
3. Run a silicone bead along the holes on the wall. Attach the Wall profile for small stationary glass (01) and Pivot retainer (08) to the wall using Round head screws ST4.2×40 (18). 1 See Fig. 3 for details. 2 3 Fig. 3 4. Apply clear silicone along the inner channel of the Glass profile for small stationary glass (02) and push the Small stationary glass (03) inside the channel.
5. Attach the Pivot brackets (09) to the top and the bottom end of the assembled Small stationary glass (03) and the Glass profile for small stationary glass (02) with the Flat head screws ST4.2×25 (17). 1 See Fig. 5 for details. 2 Fig. 5 6. Assemble the Glass fixer (10) to the top and the bottom hole of the Small stationary glass (03). Fasten the top Glass fixer (10) to the top Pivot bracket (09) using Fixing nut with M4×12 screw (13) and cover screw location with decorative cover. 1 2 See Fig.
7. Slide the Small stationary glass assembly into the groove of the Wall profile for small stationary glass (01). See Fig. 7 for details. 1 2 Fig. 7 8. Secure the upper Pivot bracket (09) to the upper Pivot retainer (08) with Socket head screw M6×6 (14). Adjust the Small stationary glass (03) vertically using a level and fix it in the place by tightening the Socket head screw M6×6.
9. Attach the top and the bottom Pivot assemblies (12) to the Pivot brackets (09). Make sure the Washer (11) is in between Pivot assemblies and Pivot brackets and the rubber gaskets between the glass and the metal parts. Slide the Glass door (04) into groove of the Pivot assemblies and tighten the provided fasten bolts. Push the Magnetic strip on door (23) on the vertical edge of the Glass door. 1 2 3 4 See Fig. 9 for details.
10. Push the Glass profile (05) into the groove of the Wall profile (06) and push the Magnetic strip on jamb (24) into the groove of the Glass profile. Close the Glass door (04). Adjust the position of the Glass door and position of the Wall profile on the wall to ensure the Magnetic strips are able to contact each other properly. In this process, you have to use a level to ensure that the Glass door is absolutely vertical. Draw a line along the vertical edge of the Wall profile on the wall.
. Mount the Handle (07) onto the Glass door (01). Attach the Bottom anti-water strip (21) onto the glass door. (You can cut the strip to size by using a knife). See Fig. 12 for details. 1 2 Fig. 12 13. Apply silicone sealant between the tray or threshold and the pivot bracket. Also, apply silicone between the wall and the wall profiles. See Fig. 13 for details. Waterproof Silicone Fig. 13 “Allure” Rev.3 Ver.
Stationary Glass Installation 14. Push the Magnetic strip (33) on the vertical edge of the Glass door (04). Apply clear silicone along the inner channel of the Glass profile (05) and push the Stationary glass (25) inside the channel. NOTE: If you have difficulty sliding the Glass profile over the Stationary glass, you can slightly tap on the Glass profile with a rubber mallet and a piece of wood. Please do not strike directly on the profile or on the edge of the glass panel.
16. Slide the Stationary glass (04) with the Glass profile (05) back into the groove of the Wall profile (06). Readjust the Glass door (04) to ensure that Magnetic strips (33) work as desired. 1 2 3 4 See Fig. 16 for details. Fig. 16 17. Install the Bracket (32) onto the stationary glass and drill the hole into the Shower base or the threshold using Ø 1/8” drill bit. Use Round head screws ST4.2×25 (30) to attach the Bracket to the Shower base or the threshold.
18. After final adjustments of the Assembled unit drill six holes, three on each side, through the first layer of the Wall profiles and the Glass profiles using Ø 1/8” drill bit. Secure the Wall profile (06) and the Glass profile (05) with Flat head screws ST4.2×10 (16). Cover the screw locations with Decorative cover (20). 2 1 Ø1/18” 3 4 Ø1/8” See fig. 18 for details 5 6 Fig. 18 19. Mount the Handle (07) to the Glass door (05).
Glass shelves installation 20. Mark the Glass shelf (34) position on the wall. According to the measurements in Fig. 19.1, mark the drilling holes on the wall for the Shelf brackets (26). Drill the holes using Ø 5/16” drill bit and insert the Wall anchors (28). Attach the Shelf brackets (26) to the wall using the Flat head screw ST4.2×25 (29) and attach the Shelf brackets (27) to the Stationary glass (25). Insert the Glass shelves into the Shelf brackets and fasten the screws at the bottom of the brackets.
21. Apply silicone sealant between the tray or threshold, the stationary glass and the accessory. Also, apply silicone between the wall and the wall profiles. See Fig. 22 for details. Waterproof Silicone Fig. 22 NOTE: If you need another direction for the door opening, you need only to exchange the position of the pivot assembly (12). See Fig. 22 & Fig. 23 Fig. 23 “Allure” Rev.3 Ver.
Maintenance To insure long lasting life for your acrylic back walls, wipe them off after each use with a soft cloth. To clean the acrylic back walls use non-abrasive sprays or cream based cleaners. Never use abrasive cleansers, metal brushes or scrapers that could scratch or dull the surface. To insure long lasting life for your glass shower products, wipe them off after each use with a soft cloth. Rinse and wipe of the glass using either soft cloth or squeegee to prevent soap buildup.
SLIMLINE SHOWER BASE SHOWER BASE DIMENSIONS AND INSTALLATION INSTRUCTIONS IMPORTANT DreamLineTM reserves the right to alter, modify or redesign products at any time without prior notice. For the latest up-to-date technical drawings, manuals or any other details please refer to the support.BathAuthority.com web page. Please read these instructions carefully before installing.
Preparation 1. Examine boxes and packages for shipping damage. Carefully remove Shower base from the packaging and check for any visual defects or shipping damages. If the unit has been damaged, has a finishing defect, or has missing parts, please contact our customer support department within 5 business days of the delivery date. Please note that DreamLineTM will not replace any damaged products or missing parts free of charge after 5 business days or if the product has been installed.
SINGLE THRESHOLD SHOWER BASE Center Drain Configuration W W1 D1 D MODEL SPECIFICATION D (in) W (in) D1 (in) W1 (in) DLT-1132320 DLT-1136360 DLT-1136480 DLT-1130600 DLT-1132600 DLT-1134600 DLT-1136600 32"×32" 36"×36" 36"×48" 30"×60" 32"×60" 34"×60" 36"×60" 32" 36" 36" 30" 32" 34" 36" 32" 36" 48" 60" 60" 60" 60" 16" 15" 15" 15" 15" 15" 15" 16" 18" 24" 30" 30" 30" 30" “SLIMLINE SHOWER BASE” Rev.3 Ver.
Left-Hand Drain Configuration W W1 D1 D MODEL SPECIFICATION D (in) W (in) D1 (in) W1 (in) DLT-1130601 DLT-1132601 DLT-1134601 DLT-1136601 30"×60" 32"×60" 34"×60" 36"×60" 30" 32" 34" 36" 60" 60" 60" 60" 15" 15" 17" 18" 12" 12" 12" 12" “SLIMLINE SHOWER BASE” Rev.3 Ver.
Right-Hand Drain Configuration W W1 D1 D MODEL SPECIFICATION D (in) W (in) D1 (in) W1 (in) DLT-1130602 DLT-1132602 DLT-1134602 DLT-1136602 30"×60" 32"×60" 34"×60" 36"×60" 30" 32" 34" 36" 60" 60" 60" 60" 15" 15" 17" 18" 12" 12" 12" 12" “SLIMLINE SHOWER BASE” Rev.3 Ver.
NEO SHOWER BASE W C C A W B A MODEL SPECIFICATION W (in) A (in) B (in) C (in) DLT-2036360 DLT-2038380 DLT-2040400 DLT-2042420 36"×36" 38"×38" 40"×40" 42"×42" 36" 38" 40" 42" 18 5/16" 20 5/16" 22 5/16" 24 5/16" 25" 25" 25" 25" 12" 12" 14 3/8" 14 3/8" “SLIMLINE SHOWER BASE” Rev.3 Ver.
QUARTER ROUND SHOWER BASE W C C W R MODEL SPECIFICATION W (in) C (in) R (in) DLT-7033330 DLT-7036360 DLT-7038380 33"×33" 36"×36" 38"×38" 33" 36" 38" 12" 12" 12" 21 5/8" 21 5/8" 21 5/8" “SLIMLINE SHOWER BASE” Rev.3 Ver.
DOUBLE THRESHOLD SHOWER BASE Corner Drain Configuration W C C W MODEL SPECIFICATION W (in) C (in) DLT-1032320 DLT-1036360 32"×32" 36"×36" 32" 36" 12" 12" “SLIMLINE SHOWER BASE” Rev.3 Ver.
Left-Hand Drain Configuration W W1 D1 D MODEL SPECIFICATION D (in) W (in) D1 (in) W1 (in) DLT-1034481 DLT-1036481 DLT-1036601 34"×48" 36"×48" 36"×60" 34" 36" 36" 48" 48" 60" 17" 18" 18" 12" 12" 12" “SLIMLINE SHOWER BASE” Rev.3 Ver.
Right-Hand Drain Configuration W W1 D1 D MODEL SPECIFICATION D (in) W (in) D1 (in) W1 (in) DLT-1034482 DLT-1036482 DLT-1036602 34"×48" 36"×48" 36"×60" 34" 36" 36" 48" 48" 60" 17" 18" 18" 12" 12" 12" “SLIMLINE SHOWER BASE” Rev.3 Ver.
Diagram of the Shower Base in a Cross Section Cement board Finished Wall Shower Base (2"×4") Stud Mortar/Plaster Drain “SLIMLINE SHOWER BASE” Rev.3 Ver.
Shower Base Installation Preparation 1. Ensure that the floor and the studs are at right angle. Provide a 5”×5” opening in the subfloor for the drain. The 2” PVC waste pipe should extend above the surface of the sub-floor according to the drain installation instructions and the height of the Shower base. Refer to the product drawings in these installation instructions for the drain location. 90° 90° 90° See Fig. 1 and Fig. 2 for details.
2. Install the shower drain (NOT PROVIDED) according to the drain installation manual (supplied with the drain). See Fig. 3 for details. Fig. 3 3. Place the tray into the designated position so that the Drain Body drops around the Drain Pipe and butt the Shower Base up against the studs. See Fig. 4 for details. Lift and lower base over the center of The drain pipe and set it into the place Fig. 4 “SLIMLINE SHOWER BASE” Rev.3 Ver.
4. Level the tray and place marks on the studs above the upper edge of the tile flange. See Fig. 5 for details. Level base in two directions Fig. 5 5. Mix the bedding material (Mortar, Plaster, etc). Concrete is not recommended. Apply enough bedding material to support the entire bottom of the shower base. See Fig. 6 for details. Mortar/Plaster Fig. 6 “SLIMLINE SHOWER BASE” Rev.3 Ver.
6. After the bedding material has been poured and before it sets, place the shower base into the position with the drain assembly sliding over the PVC waste pipe. It will be necessary to push the shower base until the top of the tile flange aligns with the marks drawn on the studs and the front edge is contacting the rough floor along the entire length of the shower base. Ensure that the base is level in all directions.
Fig. 9 Product maintenance To insure long lasting life for your acrylic back walls, wipe them off after each use with a soft cloth. To clean the acrylic back walls use non-abrasive sprays or cream based cleaners. Never use abrasive cleansers, metal brushes or scrapers that could scratch or dull the surface. To insure long lasting life for your glass shower products, wipe them off after each use with a soft cloth. Rinse and wipe of the glass using either soft cloth or squeegee to prevent soap buildup.
DREAMLINE™ EXCLUSIVE LIMITED WARRANTY AS OF MAY 6, 2013 This warranty extends only to the original owner/end‐user for household use only and is not transferable to a subsequent owner. This warranty extends for a designated period of time, so long as it remains in use in its original place of installation. This warranty applies only to DreamLine products purchased from an authorized dealer in United States or Canada.
TEL: 866-731-2244 FAX: 866-227-1533 WWW.BATHAUTHORITY.COM For more information on DreamLineTM Shower Doors please visit www.BathAuthority.