Butterfly Shower Door, Base & Backwall Kit SHOWER Door, SHOWER BASE AND BACKWALLS KIT INSTALLATION INSTRUCTIONS IMPORTANT DreamLineTM reserves the right to alter, modify or redesign products at any time without prior notice. For the latest up-to-date technical drawings, manuals or any other details please refer to the support.BathAuthority.com web page.
BUTTERFLY SHOWER DOOR & TUB DOOR INSTALLATION INSTRUCTIONS IMPORTANT DreamLineTM reserves the right to alter, modify or redesign products at any time without prior notice. For the latest up-to-date technical drawings, manuals or any other details please refer to the support.BathAuthority.com web page. Symmetrical Model Asymmetrical Model Please read these instructions carefully before installing.
Preparation 1. After opening all boxes and packages, read this introduction carefully. Check that all of the needed parts are included in the package by marking all the components on the “Detailed Diagram of Shower Door Components”. Examine boxes and packages for shipping damage. If the unit has been damaged, has a finishing defect, or is missing parts, please contact our customer support department within 5 business days of the delivery date.
Detailed Diagrams of Shower Door Components 11 2 1 12 9 10 8 7 3 4 13 3 5 6 14 A B 15 B2 16 A2 17 18 19 Packing List 01 02 03 04 05 06 07 08 09 10 Wall profile Glass profile Guide rail Glass door A/A2 Glass door B/B2 Wall anchor Round head screw ST4.2×10 Big flat head screw ST4.2×12 Big flat head screw ST4.
Shower Door Assembly Note: There are two separate Butterfly models featuring two different glass variations. Please refer to the drawings on page 1 as a visual guide for the product you purchased. The Asymmetrical Butterfly model installation is depicted below. These instructions can be used as a general guide for the Symmetrical Butterfly model installation.
2. Attach the top and the bottom Hinges (13) to the left edge of the Glass door A (04). Mind the position of the Hinges on the glass. 3/4 " 1 See Fig. 2 and Fig. 5 for details. A 2 Fig. 2 3. Attach the top and the bottom Roller hinges (12) to the right edge of the Glass door B (05). Mind the position of the Roller hinges on the glass. 3/4 " 1 See Fig. 3 and Fig. 5 for details. B 2 Fig. 3 “BUTTERFLY” Rev.3 Ver.
4. Connect the Glass door A (04) to the Glass door B (05) using the Middle hinges (11). Mind the position of the Middle hinges on the glass. 3 1 See Fig. 4 and Fig. 5 for details. A A B 4 2 A B A B Fig. 4 Door assembly 1 A B Fig. 5 “BUTTERFLY” Rev.3 Ver.
5. Place the other Glass door B2 (05) and the other Glass door A2 (04) on a flat surface. The distances from the glass edge to the paired holes on both sides of the Glass door are different. The side of each Glass door where the paired holes are closer to the edge should be facing each other. 3/4 " 3 /4 " B2 See Fig. 6 for details. A2 Fig.6 Fig. 6 6. Attach the top and the bottom Roller hinges (12) to the left edge of the Glass door B2 (05). Mind the position of the Roller hinges on the glass.
7. Attach the top and the bottom Hinges (13) to the right edge of the Glass door A2 (04). Mind the position of the Hinges on the glass. 3/4 " 1 See Fig. 8 and Fig. 10 for details. A2 2 Fig. 8 8. Connect the Glass door B2 (05) to the Glass door A2 (04) using Middle hinges (11). Mind the position of the Middle hinges on the glass. 3 1 See Fig. 9 and Fig. 10 for details. B2 B2 A2 4 2 B2 A2 B2 A2 Fig. 9 “BUTTERFLY” Rev.3 Ver.
Door assembly 2 B2 A2 Fig. 10 9. Locate the Guide rails (03) and the Glass profile (02). Connect the left end of the Guide rails to the Glass profile using the Big flat head screws ST4.2×40 (09). 1 See Fig. 11 for details. NOTICE: Make sure that the Seal strip flange on the Glass profile is pointing in towards the shower. 2 Fig. 11 “BUTTERFLY” Rev.3 Ver.
10. Slide the pre-installed Door assembly 1 (as showing in Fig. 5) into the channel of the Guide rails (03) from the right side. 1 3 2 4 See Fig. 12 and Fig. 13 for details. Fig. 12 11. Secure the Hinges (13) inside the Guide rails (03) using the Big flat head screw ST4.2×12 (08). See Fig. 13 for details. 1 2 Fig. 13 “BUTTERFLY” Rev.3 Ver.
. Slide the pre-installed Door assembly 2 (that showing on Fig. 10) into the channel of the Guide rails (03) from the right side. 1 3 2 4 See Fig. 14 and Fig. 15 for details. Fig. 14 Fig. 15 “BUTTERFLY” Rev.3 Ver.
1 13. Attach the other Glass profile (02) at the right side of the door unit and fasten it to the Guide rails (03) with the Big flat head screw ST4.2×40 (09). See Fig. 16 and Fig. 18 for details. NOTE: Make sure that the Seal strip flange on the Glass profile is pointing inside the Shower. 2 Fig. 16 1 14. Secure the right Hinges (13) inside the Guide rails (03) using the Big flat head screw ST4.2×12 (08). See Fig. 17 and Fig. 18 for details. 2 Fig. 17 “BUTTERFLY” Rev.3 Ver.
A B B2 A2 A B B2 A2 Fig. 18 15. Attach the Roller stoppers (16) inside the top and the bottom Guide rails (03) with the Big flat head screw ST4.2×12 (08). 1 3 2 4 See Fig. 19 for details. Fig. 19 “BUTTERFLY” Rev.3 Ver.
Shower Door Installation 16. The Tub or Shower base should be installed prior to installation. The Shower base should be installed according to the Shower base installation manual. See Fig. 20 and 21 for details. Fig. 20 “BUTTERFLY” Rev.3 Ver.3 03/2014 Fig.
1 17. Push the Wall profiles (01) over the Glass profiles (02) on both sides. Be sure that the flanges with predrilled holes are pointing in towards the shower. See Fig. 22 and Fig. 23 for details. 2 Fig. 22 A B B2 A2 Fig. 23 “BUTTERFLY” Rev.3 Ver.
18. Move the assembled Door unit on the Shower base or the Tub and butt the Wall profiles (01) up against the walls. Level the Door unit vertically. You can adjust position of the Door unit by slightly pulling the Glass profiles (02) out of the Wall profiles. A A B B B2 B A2 A See Fig. 24 and Fig. 25 for details. Symmetrical Model Asymmetrical Model Fig. 24 19. Trace the drilling holes on the wall through the predrilled holes in the Wall profile (01). Move the Door unit aside.
20. Make final adjustment if required. Drill the holes through the first layer into the Wall profiles (01) and the Glass profiles (02) using Ø 1/8 drill bit. Secure the Wall profiles and the Glass profiles with the Round head screws ST4.2×10 (07). Use the raised white washer with the screw and attach the Decorative Covers (10). See Fig. 27 for details. 1 3 2 4 Ø 1/8" Fig. 27 21. Adjust the Roller hinges (12) to make the door slide smoothly. 1 See Fig. 28 for details. 2 Fig. 28 “BUTTERFLY” Rev.
1 22. Mount the Handles (17) onto the both Glass doors B & B2 (05). Cover the screw holes on the Handles with the provided decorative plugs. See Fig. 29 for details. 2 Fig. 29 23. Open the door and attach Side anti-water strips (15) to both vertical edges of the Glass doors. The strip flange should point away from the shower faucet. Attach Magnetic strips (19) to both vertical edges of the Glass doors B & B2 (05). 1 3 A B B See Fig. 30 for details. 2 4 B2 A2 B2 Fig. 30 “BUTTERFLY” Rev.3 Ver.
24. Apply silicone along the Wall profiles (01), as well as along the bottom Guide rail (03). See Fig. 31 for details. A B B2 A2 Caulk Caulk Fig. 31 Product Maintenance To ensure long lasting life for your acrylic back walls, wipe them off after each use with a soft cloth. To clean the acrylic back walls use non-abrasive sprays or cream based cleaners. Never use abrasive cleansers, metal brushes or scrapers that could scratch or dull the surface.
QWALL – 5.2 (2 Back Panels) SHOWER ACRYLIC WALL INSTALLATION INSTRUCTIONS IMPORTANT DreamLineTM reserves the right to alter, modify or redesign products at any time without prior notice. For the latest up-to-date technical drawings, manuals or any other details please refer to the support.BathAuthority.com web page. Please read these instructions carefully before installing.
Preparation 1. After opening all boxes and packages, read this introduction carefully. Check that all of the needed parts are included in the package by marking all the components on the “Detailed Diagram of Shower Door Components”. Examine boxes and packages for shipping damage. If the unit has been damaged, has a finishing defect, or has missing parts, please contact our customer support department within 5 business days of the delivery date.
Detailed Diagram of Acrylic Shower Wall Components 2 1 46 58 "- 50 "- 6 " 2" 3 4 5 6 10 7 8 9 Packing List 01 Side panel 2pcs 06 Wall anchor 21pcs 02 Corner cover 2pcs 07 Countersunk screw ST4.2×30 21pcs 03 Decorative edge molding 2pcs 08 Decorative cover 15pcs 04 Shelf bracket 6pcs 09 Back panel 2pcs 05 Glass shelf 2pcs 10 Center cover 1pc NOTE: Unpack your unit carefully and inspect it.
Preparation for Installation of Back Panel 1. Place a mark on the walls at a distance of 1” (one inch) from the corner and draw a plumb vertical line from top to bottom. 1 1" See Fig. 1 for details. NOTE: Repeat this step for both corners. 2 1" Fig. 1 2. The Shower back wall kit has two Back Panels (09). Measure the back wall of the shower between the vertical lines you marked in Step 1. This distance is marked as “W”. W See Fig. 2 for details. Fig. 2 Ver. 1, Rev.
3. Divide the measurement “W” by two and place a mark in the center of the back wall and from there draw a plumb vertical line from top to bottom. W/ 2 W/ 2 This distance is shown as “W/2”. See Fig. 3 for details. Fig. 3 4. Determine the position of both Back panels (09).
5. Measure the Back Panel (09). Width of the Back Panel has to be less than or equal to the distance between the center line and the corner line on the back wall in Step. 3 L ≤ W/2 L L If the width of the Back Panel is greater than the distance between the center line and the corner line on the back wall in Step. 3, you have to trim the Back Panel to fit your measurement. See Fig. 5 for details. Fig. 5 6.
7. Place the Back Panel (09) onto a flat piece of plywood or particle board. Use a sharp industrial knife and a T-square to score along the marked side ends of the Back panel and continue scoring until you have fully cut through the panel. See Fig. 7 and Fig. 8 for details. 1 2 Fig. 7 W/ 2 W/ 2 Fig. 8 Ver. 1, Rev.
Preparation for Installation of Side Panels ATTENTION: If you are installing a shower door with a wall profile, you can hide the edge of the Side panel (01) behind the wall profile. Side Panel 1 Wall Profile Wall See Fig. 9 for details. Side Panel 2 Wall Profile Wall Fig. 9 8. Measure the side walls of the shower from the 1” (one inch) line in the corner (from Step. 1) to the distance where you want Side panels (01) to end. The distance is “D”. D D See Fig. 10 for details. Fig. 10 Ver. 1, Rev.
9. Determine the position of both Side panels (01). NOTE: a) The narrow edge of the Side panel fits behind the corner cover and cannot be trimmed. b) The wide edge of the Side panel can be trimmed to the size of your measurements from Step. 8. D D Line to cut Line to cut Measure from the narrow edge of the Side panel and place a mark at a distance of "D" (that you measured in Step. 8). Draw a straight line from top to bottom along the wide edge of the Side panel. See Fig. 11 for details. Fig. 11 10.
D D Fig. 13 11. Take exact measurements of the fixture on the wall: • • 1" D A from the 1” (one inch) line in the corner of the shower to the fixture: (A, B, C) from the bottom of the wall of the shower to the fixture: (E, F). See Fig. 14 for details. C E B F Fig. 14 Ver. 1, Rev.
12. Determine which Side panel (01) will be installed on the side wall with the fixture. Mark the fixture location on the Side panel according to the measurements taken in Step. 11. A D See Fig. 15 for details. E F B C Fig. 15 13. Drill the holes for the fixtures in the Side panel (01) using the proper diameter saw bit or a handheld jig saw. D See Fig. 16 for details. Fig. 16 Ver. 1, Rev.
Acrylic Back Panel and Side Panel Installation Instruction 14. Attach the Center cover (10) vertically at the center point along the line (from Step. 3) and mark the drilling holes through the predrilled holes in the Center cover. Drill the holes using Ø5/16” drill bit and insert the Wall Anchors (06). 1 2 3 4 See Fig. 17 for details. Ø5/16" Fig. 17 15. Mount the Center cover (10) to the centerline of the back wall using the Countersunk screws ST4.2×30 (07).
W/ 2 W/ 2 Fig. 19 16. Attach the Corner cover (02) to the corner of the shower and mark the drilling holes through the predrilled holes in the Corner cover. Move aside the Corner cover, Drill the holes using Ø5/16” drill bit and insert the Wall Anchors (06). See Fig. 20 and Fig. 21 for details 1 2 3 4 Ø5/16" Fig. 20 Ver. 1, Rev.
W/ 2 W/ 2 Fig. 21 ATTENTION: Installation of all Acrylic panels must be finished before the sealant sets for easy leveling and adjustments. W/ 2 W/ 2 17. Apply the sealant to the entire surface of the reverse side of the Back panel (09). See Fig. 22 for details. Fig. 22 Ver. 1, Rev.
1 18. Slide the right edge of the left Back panel (09) all the way behind the Center cover (10) and push the Back panel against the wall. Slide the left edge of the right Back panel (09) all the way behind the Center cover (10) and push the Back panel against the wall as well. You can adjust the position of the Back panels before the sealant sets. Apply equal pressure to the whole surface of the Back panels from top to bottom. 2 See Fig. 23 and Fig. 24 for details. 3 Fig. 23 Fig. 24 Ver. 1, Rev.
19. Mount the Corner cover (02) to the corner of the shower using the Countersunk screws ST4.2×30 (07). Do not fully tighten the screws at this time; leave them loose for further installation. See Fig. 25 for details 1 2 3 4 Fig. 25 20. Apply the sealant to the entire surface of the reverse side of the Side panel (01). Also, apply the sealant around the drilled holes. See Fig. 26 for details. Fig. 26 Ver. 1, Rev.
21. Slide the narrow edge of the Side panel (01) behind the Corner cover (02). Align trimmed edge of the Side panel (from Step. 9) with the marked line on the wall (in Step. 7) and push the Side panel against the wall. NOTE: Make sure the drilled holes on the Side panel are also aligned with the fixtures on the wall. See Fig. 27 for details. 1 2 Fig. 27 22. Apply sealant to the entire surface of the reverse side of the other Side panel (01). See Fig. 26 for details.
23. Once all panels are aligned, fasten tight the Corner cover (02) to secure the Side panels (01) and Back panels (09). Cover the screw holes with the Decorative covers (08). 1 See Fig. 29 for details. 2 Fig. 29 1 24. Fasten tight the Center cover (10) to secure the Back panels (09). Cover the screw holes with the Decorative covers (08). See Fig. 30 for details. 2 Fig. 30 Ver. 1, Rev.
ATTENTION; Prior to the next step, please be sure the part of the wall for installation of the Decorative edge molding (03) is clean, dry and free from soap, oil and any construction debris. 25. Gently remove the plastic tape from the adhesive side of the Decorative edge molding (03) and firmly press it to the edge of the Side panel (01) from top to bottom. See Fig. 31 for details. 1 Side Panel Wall Decorative Molding Side Panel 2 Wall Decorative Molding Fig. 31 26.
Glass Shelves Installation Instruction 27. Determine the desired height for the Glass shelves (05) and mark the locations on the wall. NOTE: The Glass shelves can be installed either two in one corner, or one in each. See Fig. 33 for details. G H ` Fig. 33 3 1/2" 28. Mark the location for the Shelf brackets (04) according to the measurements in Fig. 28 and Fig. 29.1. Drill the holes using Ø5/16” drill bit and insert the Wall anchors (06). See Fig. 34 for details. 3 1/2" 3 1/2" 1 Ø 5/16" 2 3 Fig.
1 29. Mount the Shelf brackets (04) to the wall using the Countersunk screws ST4.2×30 (07). NOTE: the padded set screw of the Glass bracket should be facing down. Slide the upper Glass shelf (05) into the upper Shelf brackets and tighten the set screws at the bottom of the brackets. Then slide the bottom Glass shelf in place. Tighten the set screws on the bottom Shelf brackets as well. 2 See Fig. 35 and Fig. 36 for details. 3 Fig. 35 Fig. 36 Ver. 1, Rev.
Product maintenance To insure long lasting life for your acrylic back walls, wipe them off after each use with a soft cloth. To clean the acrylic back walls use non-abrasive sprays or cream based cleaners. Never use abrasive cleansers, metal brushes or scrapers that could scratch or dull the surface. Acrylic cleaning procedure: Acrylic should be cleaned with warm water and a clean, nonabrasive cloth. If desired, a mild, non-abrasive detergent may also be used. Use only light pressure when cleaning.
SLIMLINE SHOWER BASE SHOWER BASE DIMENSIONS AND INSTALLATION INSTRUCTIONS IMPORTANT DreamLineTM reserves the right to alter, modify or redesign products at any time without prior notice. For the latest up-to-date technical drawings, manuals or any other details please refer to the support.BathAuthority.com web page. Please read these instructions carefully before installing.
Preparation 1. Examine boxes and packages for shipping damage. Carefully remove Shower base from the packaging and check for any visual defects or shipping damages. If the unit has been damaged, has a finishing defect, or has missing parts, please contact our customer support department within 5 business days of the delivery date. Please note that DreamLineTM will not replace any damaged products or missing parts free of charge after 5 business days or if the product has been installed.
SINGLE THRESHOLD SHOWER BASE Center Drain Configuration W W1 D1 D MODEL SPECIFICATION D (in) W (in) D1 (in) W1 (in) DLT-1132320 DLT-1136360 DLT-1136480 DLT-1130600 DLT-1132600 DLT-1134600 DLT-1136600 32"×32" 36"×36" 36"×48" 30"×60" 32"×60" 34"×60" 36"×60" 32" 36" 36" 30" 32" 34" 36" 32" 36" 48" 60" 60" 60" 60" 16" 15" 15" 15" 15" 15" 15" 16" 18" 24" 30" 30" 30" 30" “SLIMLINE SHOWER BASE” Rev.3 Ver.
Left-Hand Drain Configuration W W1 D1 D MODEL SPECIFICATION D (in) W (in) D1 (in) W1 (in) DLT-1130601 DLT-1132601 DLT-1134601 DLT-1136601 30"×60" 32"×60" 34"×60" 36"×60" 30" 32" 34" 36" 60" 60" 60" 60" 15" 15" 17" 18" 12" 12" 12" 12" “SLIMLINE SHOWER BASE” Rev.3 Ver.
Right-Hand Drain Configuration W W1 D1 D MODEL SPECIFICATION D (in) W (in) D1 (in) W1 (in) DLT-1130602 DLT-1132602 DLT-1134602 DLT-1136602 30"×60" 32"×60" 34"×60" 36"×60" 30" 32" 34" 36" 60" 60" 60" 60" 15" 15" 17" 18" 12" 12" 12" 12" “SLIMLINE SHOWER BASE” Rev.3 Ver.
NEO SHOWER BASE W C C A W B A MODEL SPECIFICATION W (in) A (in) B (in) C (in) DLT-2036360 DLT-2038380 DLT-2040400 DLT-2042420 36"×36" 38"×38" 40"×40" 42"×42" 36" 38" 40" 42" 18 5/16" 20 5/16" 22 5/16" 24 5/16" 25" 25" 25" 25" 12" 12" 14 3/8" 14 3/8" “SLIMLINE SHOWER BASE” Rev.3 Ver.
QUARTER ROUND SHOWER BASE W C C W R MODEL SPECIFICATION W (in) C (in) R (in) DLT-7033330 DLT-7036360 DLT-7038380 33"×33" 36"×36" 38"×38" 33" 36" 38" 12" 12" 12" 21 5/8" 21 5/8" 21 5/8" “SLIMLINE SHOWER BASE” Rev.3 Ver.
DOUBLE THRESHOLD SHOWER BASE Corner Drain Configuration W C C W MODEL SPECIFICATION W (in) C (in) DLT-1032320 DLT-1036360 32"×32" 36"×36" 32" 36" 12" 12" “SLIMLINE SHOWER BASE” Rev.3 Ver.
Left-Hand Drain Configuration W W1 D1 D MODEL SPECIFICATION D (in) W (in) D1 (in) W1 (in) DLT-1034481 DLT-1036481 DLT-1036601 34"×48" 36"×48" 36"×60" 34" 36" 36" 48" 48" 60" 17" 18" 18" 12" 12" 12" “SLIMLINE SHOWER BASE” Rev.3 Ver.
Right-Hand Drain Configuration W W1 D1 D MODEL SPECIFICATION D (in) W (in) D1 (in) W1 (in) DLT-1034482 DLT-1036482 DLT-1036602 34"×48" 36"×48" 36"×60" 34" 36" 36" 48" 48" 60" 17" 18" 18" 12" 12" 12" “SLIMLINE SHOWER BASE” Rev.3 Ver.
Diagram of the Shower Base in a Cross Section Cement board Finished Wall Shower Base (2"×4") Stud Mortar/Plaster Drain “SLIMLINE SHOWER BASE” Rev.3 Ver.
Shower Base Installation Preparation 1. Ensure that the floor and the studs are at right angle. Provide a 5”×5” opening in the subfloor for the drain. The 2” PVC waste pipe should extend above the surface of the sub-floor according to the drain installation instructions and the height of the Shower base. Refer to the product drawings in these installation instructions for the drain location. 90° 90° 90° See Fig. 1 and Fig. 2 for details.
2. Install the shower drain (NOT PROVIDED) according to the drain installation manual (supplied with the drain). See Fig. 3 for details. Fig. 3 3. Place the tray into the designated position so that the Drain Body drops around the Drain Pipe and butt the Shower Base up against the studs. See Fig. 4 for details. Lift and lower base over the center of The drain pipe and set it into the place Fig. 4 “SLIMLINE SHOWER BASE” Rev.3 Ver.
4. Level the tray and place marks on the studs above the upper edge of the tile flange. See Fig. 5 for details. Level base in two directions Fig. 5 5. Mix the bedding material (Mortar, Plaster, etc). Concrete is not recommended. Apply enough bedding material to support the entire bottom of the shower base. See Fig. 6 for details. Mortar/Plaster Fig. 6 “SLIMLINE SHOWER BASE” Rev.3 Ver.
6. After the bedding material has been poured and before it sets, place the shower base into the position with the drain assembly sliding over the PVC waste pipe. It will be necessary to push the shower base until the top of the tile flange aligns with the marks drawn on the studs and the front edge is contacting the rough floor along the entire length of the shower base. Ensure that the base is level in all directions.
Fig. 9 Product maintenance To insure long lasting life for your acrylic back walls, wipe them off after each use with a soft cloth. To clean the acrylic back walls use non-abrasive sprays or cream based cleaners. Never use abrasive cleansers, metal brushes or scrapers that could scratch or dull the surface. To insure long lasting life for your glass shower products, wipe them off after each use with a soft cloth. Rinse and wipe of the glass using either soft cloth or squeegee to prevent soap buildup.
DREAMLINE™ EXCLUSIVE LIMITED WARRANTY AS OF MAY 6, 2013 This warranty extends only to the original owner/end‐user for household use only and is not transferable to a subsequent owner. This warranty extends for a designated period of time, so long as it remains in use in its original place of installation. This warranty applies only to DreamLine products purchased from an authorized dealer in United States or Canada.
TEL: 866-731-2244 FAX: 866-227-1533 WWW.BATHAUTHORITY.COM For more information on DreamLineTM Shower Doors please visit www.BathAuthority.
