UNIDOOR/UNIDOORLUX/UNIDOOR PLUS SINGLE SHOWER DOOR INSTALLATION INSTRUCTIONS IMPORTANT DreamLine® reserves the right to alter, modify or redesign products at any time without prior notice. For the latest up-to-date technical drawings, manuals or any other details please refer to your model’s web page on DREAMLINE.COM Right-hand installation shown ATTENTION: This model is also available with the half etched glass option. Please see specific installation instructions on page 17 when applicable.
UNIDOOR STYLES Style A Style B Style E Style I “UNIDOOR” Single Shower Door Ver.2 Rev.
Additional styles using glass-to-glass hinges: “UNIDOOR” Single Shower Door Ver.2 Rev.
STYLE A UNIDOOR Single shower door 23”-30” Refer to detailed diagram on page 5 for assembly STYLE B * UNIDOOR Shower door with 6” small or 12”-30” large stationary panel STYLE C * UNIDOOR Shower door with 12”-30” large stationary panel STYLE D * UNIDOOR LUX Shower door with 6” small or 14”-30” large stationary panel STYLE E * UNIDOOR LUX Shower enclosure with 30” return stationary panel STYLE F * UNIDOOR PLUS Shower door with 6”-34” in-line stationary panel secured using u-channel STYLE G * UNIDOOR S
STYLE M3 * UNIDOOR Shower door 23”~30” with 6” or 24” hinge panel and full height inline panel and full height return panel secured using u-channel STYLE M4 * UNIDOOR Shower door 23”~30” with 6” or 24” hinge panel, in-line buttress panel and buttress return panel secured using u-channel STYLE L1 * UNIDOOR Shower door 23”~30” with 6” or 24” hinge panel and full height return panel secured using u-channel All sizes shown above are nominal dimensions * For the panel installation instructions, please refer to
Preparation 1. Prior to installation, examine all boxes and packages for shipping damage and compare piece count with your packing slip. After opening all boxes and packages, read this introduction carefully. Check that all of the needed parts are included in the package by marking all the components on the “Detailed Diagram of Shower Door Components”.
Tools Required Tape Measure Pencil Level “UNIDOOR” Single Shower Door Ver.2 Rev.
Detailed Diagram of Shower Door Components 4 1 31 5 2 6 7 8 Packing List Part# 01 02 04 05 Description Glass door Handle Countersunk screw ST5×70 Hinge with Adjustable angle Qty 1pc 1pc 8pcs 2pcs Part# 06 07 08 31 Description Side strip ( 3 sections to cut) Bottom anti-water strip L-shaped strip PVC hinge spacer Qty 1pc 1pc 1pc 4pcs NOTE: Unpack your unit carefully and inspect it. Lay out and identify all parts using the detailed diagram and packing list in this manual as a reference.
Single Shower Door Assembly and Installation NOTE: The following shower door installation instructions should be used as a general guide and prerequisite to the installation of the UNIDOOR, UNIDOORLUX and UNIDOOR PLUS models. Before you begin the installation, please check your finished opening size. Specific size information can be found on our website at DreamLine.com.
ATTENTION: For model Styles E, I, J, K & L, that have return panels: Please check model dimensions for proper placement of the Glass door (01) so that it will align correctly with the return panel glass. ATTENTION: Check the door glass with a level to verify that it is plumb before marking the hinge positions. 5/8" 2. Place a piece of 5/8” thick flat wood or a spacer of equal thickness on the threshold or shower base.
1 TIP: The PVC hinge spacer can also be used as a template to assist with marking the hinge mounting holes. 2 NOTE: DO NOT attach the handle to the door glass until instructed to do so. DO NOT use the handle to lift the glass during installation. This may result in damage to the glass and/or serious injury. Always use an assistant or a professional grade glass suction cup when handling the door glass. 3 Fig.
Setting the Adjustable Hinges The Adjustable hinges are pre-set to overclose to 85º and are adjustable up to 90º after the door is installed. Once the door glass is installed, simply loosen the allen set screws and position the door to the desired closed position. While holding the door in the new closed position, retighten the allen screws and your door will now self-center to the chosen closed position. 4a.
4b. The hinges are factory set to 85 degrees. You can change this angle by using the adjustment screws on the hinge plate. (Figure 5b) inside outside Figure 5b 4c. Use the supplied Allen Key to loosen the adjustment screws on the inside hinge plate, adjust the door to the desired angle (90 degrees for example) then retighten the adjustment screws (Figure 5c). Be sure that you create a tight seal with the supplied strike vinyl when the door is in the closed position.
5. Mount the Handle (02) to the Glass door (01). See Fig. 6 for details. Fig. 6 6. Measure the bottom of the Glass door (01) from end to end to determine the actual width of the door. Cut the Bottom anti-water strip (07) to the size of your measurement and notch 3/8” of the inner side of the Bottom anti-water strip as shown. Press the Bottom Anti-water strip onto the bottom edge of the Glass door.
1 Into the hinge Into the hinge 3 4 7/8" 7/8" Into the hinge 5 See Fig. 8 for details 2 7/8" 7. Get three measurements: from the top edge of the Glass door (01) to the upper body of the top Hinge (05) (+) 7/8” from the lower body of the upper Hinge to the upper body of the bottom Hinge (+) 1-3/4” from the lower body of the bottom Hinge to top of the installed Bottom anti-water strip (07) (+) 1-7/8” Cut the Side strip (06) according to the measurements.
Fig. 10 Product Maintenance BASES and BACKWALLS: To ensure a long life for your acrylic back walls: wipe them off after each use with a soft cloth. To clean the acrylic back walls use non-abrasive sprays or cream based cleaners. Never use abrasive cleansers, metal brushes or scrapers that could scratch or dull the surface. GLASS: To ensure long lasting life for your glass shower products: wipe them off after each use with a soft cloth.
Style “A”: Half Etched Glass Installation NOTE: This model is available with the half etched glass option. Hinged Left installation shown. To install for hinged Right, flip the door to the proper handing. -The textured surface of the glass door should face out. See Fig. 11 for details. Fig. 11 “UNIDOOR” Single Shower Door Ver.2 Rev.
TEL: 866-731-2244 FAX: 866-857-3638 DREAMLINE.COM For more information on DreamLine® Shower Doors and Enclosure please visit DreamLine.