i
Vigor2122 Series Dual Band Security Firewall Quick Start Guide Version:1.0 Firmware Version: V3.8.
Intellectual Property Rights (IPR) Information Copyrights © All rights reserved. This publication contains information that is protected by copyright. No part may be reproduced, transmitted, transcribed, stored in a retrieval system, or translated into any language without written permission from the copyright holders. Trademarks The following trademarks are used in this document: Microsoft is a registered trademark of Microsoft Corp.
Declaration of Conformity Hereby, DrayTek Corporation declares that the radio equipment type Vigor2122 is in compliance with Directive 2014/53/EU. The full text of the EU declaration of conformity is available at the following internet address: http://www.draytek.com.tw/ftp/Vigor2122/Document/CE/ Manufacturer: DrayTek Corp. Address: No. 26, Fu Shing Road, HuKou Township, HsinChu Industrial Park, Hsin-Chu County, Taiwan 303 Product: Vigor2122 Series Frequency Information for Europe area: 2.
Table of Contents 1. Introduction........................................................................................................... 1 2. Package Content .................................................................................................. 2 3. Panel Explanation ................................................................................................. 3 3.1 Vigor2122 ..................................................................................................................
1. Introduction Vigor2122 series is a broadband router which integrates IP layer QoS, NAT session/bandwidth management to help users control works well with large bandwidth. By adopting hardware-based VPN platform and hardware encryption of AES/DES/3DES, and hardware key hash of SHA-1/MD5, the router increases the performance of VPN greatly and offers several protocols (such as IPSec/PPTP/L2TP) with up to 2 VPN tunnels.
2. Package Content Take a look at the package content. If there is anything missed or damaged, please contact DrayTek or dealer immediately. Vigor Router Quick Start Guide RJ-45 Cat-5 Ethernet Cable Antenna x 2 (for “ac” model) The type of the power adapter depends on the country that the router will be installed. * The maximum power consumption is 12 Watt.
3. Panel Explanation 3.1 Vigor2122 LED ACT WCF Status Blinking Off On Blinking On Off Blinking On LAN1~LAN4 On WAN Off On Blinking USB VPN Explanation The router is powered on and running normally. The router is powered off. USB device is connected and ready for use. The data is transmitting. The VPN tunnel is active. VPN service is disabled. Traffic is passing through VPN tunnel. The Web Content Filter is active. (It is enabled from Firewall >> General Setup).
Interface Factory Reset WAN LAN 1- 4 Description Restore the default settings. Usage: Turn on the router. Press the button and keep for more than 6 seconds. Then the router will restart with the factory default configuration. Connector for accessing the Internet. Connecters for local network devices (LAN). PWR: Connecter for a power adapter. Connecter for a USB device (for 3G USB Modem or printer or storage disk). ON/OFF: Power switch.
3.2 Vigor2122ac LED ACT USB 2.4G 5G LAN1~LAN4 WAN Status Blinking Off On Blinking On Off Blinking On Off Blinking On Off Blinking On Blinking Explanation The router is powered on and running normally. The router is powered off. USB device is connected and ready for use. The data is transmitting. Wireless function is ready. Wireless function is not ready. Data is transmitting (sending/receiving). Wireless function is ready. Wireless function is not ready. Data is transmitting (sending/receiving).
Interface Description WLAN ON/OFF WPS WLAN On - Press the button and release it within 2 seconds. When the wireless function is ready, the 2.4G/5G blue LED on front panel will be on. WLAN Off - Press the button and release it within 2 seconds to turn off the WLAN function. When the wireless function is not ready, 2.4G/5G blue LED on front panel will be off. WPS - When WPS function is enabled by web user interface, press this button for more than 2 seconds.
4. Hardware Installation This section will guide you to install the router through hardware connection and configure the router’s settings through web browser. Before starting to configure the router (taking Vigor2122n for example), you have to connect your devices correctly. 4.1 Network Connection 1. Connect the cable Modem/DSL Modem/Media Converter to the WAN port of this router with Ethernet cable (RJ-45). 2.
5. Software Configuration To access Internet, please finish basic configuration after completing the hardware installation. The Quick Start Wizard is designed for you to easily set up your router for Internet access. You can directly access the Quick Start Wizard via Web Configurator. 1. Make sure your PC connects to the router correctly. Note 2.
3. Now, the Main Screen will pop up. Click Wizards>>Quick Start Wizard. Note 4. The home page will change slightly in accordance with the router you have. Enter the login password on the field of New Password and retype it on the field of Confirm Password. Then click Next to continue.
5. On the next page as shown below, please select the WAN interface that you use. If Ethernet interface is used, please choose WAN1; if 3G USB modem is used, please choose WAN2. Then click Next for next step. WAN1 and WAN2 will bring up different configuration page. Refer to the following for detailed information Here we take WAN1 (Ethernet) as an example. PPPoE 1. Choose WAN1 as the WAN Interface and click the Next button. The following page will be open for you to specify Internet Access Type.
2. Click PPPoE as the Internet Access Type. Then click Next to get the following page. 3. Manually enter the Username/Password provided by your ISP. Click Next for viewing summary of such connection. 4. Click Finish. A page of Quick Start Wizard Setup OK!!! will appear. Then, the system status of this protocol will be shown. 5. Now, you can enjoy surfing on the Internet.
PPTP/L2TP 1. Choose WAN1 as the WAN Interface and click the Next button. The following page will be open for you to specify Internet Access Type. 2. Click PPTP/L2TP as the Internet Access Type. Then click Next to continue.
3. Please type in the IP address/mask/gateway information originally provided by your ISP. Then click Next for viewing summary of such connection. 4. Click Finish. A page of Quick Start Wizard Setup OK!!! will appear. Then, the system status of this protocol will be shown. 5. Now, you can enjoy surfing on the Internet.
Static IP 1. Choose WAN1 as the WAN Interface and click the Next button. The following page will be open for you to specify Internet Access Type. 2. Click Static IP as the Internet Access type. Simply click Next to continue.
3. Please type in the IP address information originally provided by your ISP. Then click Next for next step. 4. Click Finish. A page of Quick Start Wizard Setup OK!!! will appear. Then, the system status of this protocol will be shown. 5. Now, you can enjoy surfing on the Internet.
DHCP 1. Choose WAN1/WAN2 as WAN Interface and click the Next button. The following page will be open for you to specify Internet Access Type. 2. Click DHCP as the Internet Access type. Simply click Next to continue.
3. After finished the settings above, click Next for viewing summary of such connection. 4. Click Finish. A page of Quick Start Wizard Setup OK!!! will appear. Then, the system status of this protocol will be shown. 5. Now, you can enjoy surfing on the Internet.
6. Customer Service If the router cannot work correctly after trying many efforts, please contact your dealer/DrayTek for further help right away. For any questions, please feel free to send e-mail to support@draytek.com. Be a Registered Owner Web registration is preferred. You can register your Vigor router via http://www.draytek.com. Firmware & Tools Updates Due to the continuous evolution of DrayTek technology, all routers will be regularly upgraded.
