i
Vigor2952 Series Dual-WAN Security Firewall Quick Start Guide Version: 1.0 Firmware Version: V3.8.
Intellectual Property Rights (IPR) Information Copyrights © All rights reserved. This publication contains information that is protected by copyright. No part may be reproduced, transmitted, transcribed, stored in a retrieval system, or translated into any language without written permission from the copyright holders. Trademarks The following trademarks are used in this document: Microsoft is a registered trademark of Microsoft Corp.
European Community Declarations Manufacturer: DrayTek Corp. Address: No. 26, Fu Shing Road, HuKou Township, HsinChu Industrial Park, Hsin-Chu County, Taiwan 303 Product: Vigor2952 Series DrayTek Corp. declares that Vigor2952 Series of routers are in compliance with the following essential requirements and other relevant provisions of R&TTE 1999/5/EC, ErP 2009/125/EC and RoHS 2011/65/EU.
Be a Registered Owner Web registration is preferred. You can register your Vigor router via http://www.draytek.com. Firmware & Tools Updates Due to the continuous evolution of DrayTek technology, all routers will be regularly upgraded. Please consult the DrayTek web site for more information on newest firmware, tools and documents. http://www.draytek.
Table of Contents 1. Introduction........................................................................................................... 1 2. Package Content .................................................................................................. 2 3. Panel Explanation ................................................................................................. 3 4. Hardware Installation ........................................................................................... 5 5.
1. Introduction Vigor2952 is a broadband router with dual-WAN interface. It provides policy-based load-balance, fail-over and BoD (Bandwidth on Demand), also it integrates IP layer QoS, NAT session/bandwidth management to help users control works well with large bandwidth.
2. Package Content Take a look at the package content. If there is anything missed or damaged, please contact DrayTek or dealer immediately. Vigor Router Quick Start Guide RJ-45 Cat-5 Ethernet Cable Antenna (for “n” model) The type of the power adapter depends on the country that the router will be installed. * The maximum power consumption is 17-23 Watt.
3. Panel Explanation LED Status Explanation ACT (Activity) USB1~USB2 Blinking Off On Blinking On Off On Blinking On On Blinking Off On The router is powered on and running normally. The router is powered off. A USB device is connected and active. The data is transmitting. No fiber line connected. File line connected. The WAN connection is ready. It will blink while transmitting data. The QoS function is active. Wireless access point is ready. Ethernet packets are transmitting over wireless LAN.
Right LED (Green) Interface The data is transmitting. The port is connected with 1000Mbps. The port is connected with 10/100Mbps. Description Factory Reset Wireless LAN ON/OFF/WPS Fiber WAN1~WAN2 LAN1~LAN4 USB1~USB2 PWR ON/OFF Note Blinking On Off Restore the default settings. Usage: Turn on the router (ACT LED is blinking). Press the hole and keep for more than 5 seconds. When you see the ACT LED begins to blink rapidly than usual, release the button.
4. Hardware Installation This section will guide you to install the router through hardware connection and configure the router’s settings through web browser. Before starting to configure the router (taking Vigor2952n for example), you have to connect your devices correctly. 1. Connect a cable Modem/DSL Modem/Media Converter (depends on your requirement) to any WAN port of router with Ethernet cable (RJ-45). Or, connect the fiber cable to the WAN (SFP) port of router. 2.
5. Software Configuration To access Internet, please finish basic configuration after completing the hardware installation. The Quick Start Wizard is designed for you to easily set up your router for Internet access. You can directly access the Quick Start Wizard via Web Configurator. 1. Make sure your PC connects to the router correctly. Note 2.
3. Now, the Main Screen will pop up. Click Wizards>>Quick Start Wizard. Note 4. The home page will change slightly in accordance with the router you have. Enter the login password on the field of New Password and retype it on the field of Confirm Password. Then click Next to continue.
5. On the next page as shown below, please select the WAN interface (WAN 1 to WAN4) that you use. If Fiber interface is used, please choose WAN1. If Ethernet interface is used, please choose WAN2. If USB interface is used, choose WAN3 or WAN4. Here we take WAN2 as an example. Then, click Next for next step. Note 6. There are four WAN selections available for you to choose. In which WAN3 /WAN4 is selected for 3G/4G USB modem connection.
PPPoE: If you click PPPoE as the protocol, after clicking Next, you will get the following web page. Please manually enter the Username/Password provided by your ISP. Then click Next. PPTP/L2TP: if you click PPTP/L2TP, you will get the following page. Please type in all the information originally provided by your ISP. Then click Next for next step.
Static IP: if you click Static IP, you will get the following page. Please type in the IP address information originally provided by your ISP. Then click Next for next step. DHCP: if you click DHCP, you will get the following page. Simply click Next to continue.
7. Now you can see the following screen. It indicates that the setup is complete. Different types of connection modes will have different summary. Click Finish and then restart the router. Afterward, you will enjoy surfing on the Internet. 6. Customer Service If the router cannot work correctly after trying many efforts, please contact your dealer/DrayTek for further help right away. For any questions, please feel free to send e-mail to support@draytek.com.
