i
Vigor2866 Series G.Fast Security Firewall Quick Start Guide (for RF Model) Version: 1.0_(03) Firmware Version: V4.2.
Intellectual Property Rights (IPR) Information Copyrights © All rights reserved. This publication contains information that is protected by copyright. No part may be reproduced, transmitted, transcribed, stored in a retrieval system, or translated into any language without written permission from the copyright holders. Trademarks The following trademarks are used in this document: Microsoft is a registered trademark of Microsoft Corp. Windows 8, 10 and Explorer are trademarks of Microsoft Corp.
Declaration of Conformity Hereby, DrayTek Corporation declares that the radio equipment type Vigor2866 is in compliance with Directive 2014/53/EU. The full text of the EU Declaration of Conformity is available at the following internet address: http://www.draytek.com.tw/ftp/Vigor2866/Document/CE/ Manufacturer: DrayTek Corp. Address: No. 26, Fu Shing Road, HuKou Township, HsinChu Industrial Park, Hsin-Chu County, Taiwan 303 Product: Vigor2866 Series Frequency Information for Europe area: 2.
User Manual Information Agreement This equipment complies with Part 68 of the FCC rules. Located on the equipment is a label that contains, among other information, the ACTA registration number and ringer equivalence number (REN.) If requested, this information must be provided to the telephone company. The REN is used to determine the quantity of devices which may be connected to the telephone line. Excessive REN’s on the telephone line may result in the devices not ringing in response to an incoming call.
USA Local Representative Company name ABP International Inc. Address 13988 Diplomat Drive Suite 180 Dallas TX 75234 ZIP Code 75234 E-mail rmesser@abptech.com Contact Person Mr. Robert Messer Tel. 19728311600 Caution: Any changes or modifications not expressly approved by the grantee of this device could void the user's authority to operate the equipment.
Table of Contents 1. Package Content .................................................................................................. 1 2. Panel Explanation................................................................................................. 2 2.1 Vigor2866ac / Vigor2866 ax........................................................................................................... 2 2.2 Vigor2866Vac/Vigor2866FVax ...................................................................................
1. Package Content Take a look at the package content. If there is anything missed or damaged, please contact DrayTek or dealer immediately. Besides, the content is subject to the real package. or Vigor Router Antenna (wireless models) RJ-45 Cable (Ethernet) RJ-11 to RJ-11 Cable or RJ-11 to RJ-45 Cable Quick Start Guide The type of the power adapter depends on the country that the router will be installed. * The maximum power consumption is 28 Watt.
2. Panel Explanation 2.1 Vigor2866ac / Vigor2866 ax No. LED ACT WAN2 QoS USB Status Off Blinking On Off Blinking On Off On Off Blinking On DSL Blinking (1) WCF On Off On Off 2.4G/5G Blinking DMZ On Off Blinking Explanation The router is powered off. The router is powered on and running normally. Internet connection is ready. Internet connection is not ready. The data is transmitting. The QoS function is active. The QoS function is inactive. USB device is connected and ready for use.
WAN2 / P6 Left LED (2) Right LED On Off Blinking On Off The port is connected. The port is disconnected. The data is transmitting. The port is connected with 1000Mbps. The port is connected with 10/100Mbps. On Off Blinking On Off The port is connected. The port is disconnected. The data is transmitting. The port is connected with 1000Mbps.
No. Interface Wireless LAN ON/OFF/WPS (3) Factory Reset (4) (5) Description Wireless band will be switched /changed according to the button pressed and released. For example, 2.4G (On) and 5G (On) – in default. 2.4G (Off) and 5G (On) – pressed and released the button once. 2.4G (On) and 5G (Off) – pressed and released the button twice. 2.4G (Off) and 5G (Off) – pressed and released the button three times.
DSL Connecter for installing WLAN antennas. (For ac model) (6) (7) Connecter for accessing the Internet. PWR Connecter for a power adapter. ON/OFF Power Switch.
2.2 Vigor2866Vac/Vigor2866FVax No. LED ACT WAN2 QoS USB Status Off Blinking On Off Blinking On Off On Off Blinking On DSL Blinking (1) Phone1/2 On Off Blinking 2.4G/5G On Off Blinking Explanation The router is powered off. The router is powered on and running normally. Internet connection is ready. Internet connection is not ready. The data is transmitting. The QoS function is active. The QoS function is inactive. USB device is connected and ready for use. No USB device is connected.
WAN2 / P6 Left LED (2) Right LED On Off Blinking On Off The port is connected. The port is disconnected. The data is transmitting. The port is connected with 1000Mbps. The port is connected with 10/100Mbps. On Off Blinking On Off The port is connected. The port is disconnected. The data is transmitting. The port is connected with 1000Mbps. The port is connected with 10/100Mbps LAN P1-P5 Left LED Right LED No.
5 seconds. When you see the ACT LED begins to blink rapidly than usual, release the button. Then the router will restart with the factory default configuration. (4) USB Connecter for a USB device (for 3G/4G USB Modem or printer or thermometer). WAN2 / P6 Connecter for local network devices or modem for accessing Internet. It is a switchable port. It can be used for LAN connection or WAN connection according to the settings configured in WUI. LAN P1-P5 Connecters for local network devices.
3. Hardware Installation This section will guide you to install the router through hardware connection and configure the router’s settings through web browser. Before starting to configure the router, you have to connect your devices correctly. (For the hardware connection, we take “ac” model as an example.) 3.1 Network Connection 1.
3.2 Wall-Mounted Installation Vigor router has keyhole type mounting slots on the underside. 1. Drill two holes on the wall. The distance between the holes shall be 168mm. 2. Fit screws into the wall using the appropriate type of wall plug. Note 3. The recommended drill diameter shall be 6.5mm (1/4”). When you finished about procedure, the router has been mounted on the wall firmly.
4. Software Configuration To access Internet, please finish basic configuration after completing the hardware installation. 4.1 Quick Start Wizard for Network Connection The Quick Start Wizard is designed for you to easily set up your router for Internet access. You can directly access the Quick Start Wizard via Web User Interface. Make sure your PC connects to the router correctly.
Now, the Main Screen will pop up. Click Wizards>>Quick Start Wizard. Note The home page will change slightly in accordance with the router you have. Here we take Vigor2866ac as an example. If your router can be under an environment with high speed NAT, the configuration provide here can help you to deploy and use the router quickly. The first screen of Quick Start Wizard is entering login password. After typing the password, please click Next.
click Next for next step. Each WAN interface will bring up specific configuration page. Here, we take WAN1 as an example. Click Next to go to the following page. You have to select the appropriate Internet access type according to the information from your ISP. For example, you should select PPPoA mode if the ISP provides you PPPoA interface. In addition, the field of For ADSL Only will be available only when ADSL is detected. Then click Next for next step.
PPPoE/PPPoA 1. Choose WAN1 as WAN Interface and click the Next button; you will get the following page. 2. After finished the above settings, simply click Next.
3. Please manually enter the Username/Password provided by your ISP. Then click Next for viewing summary of such connection. 4. Click Finish. A page of Quick Start Wizard Setup OK!!! will appear. Then, the system status of this protocol will be shown. 5. Now, you can enjoy surfing on the Internet.
MPoA / Static or Dynamic IP 1. Choose WAN1 as WAN Interface and click the Next button; you will get the following page. 2. Please type in the IP address/mask/gateway information originally provided by your ISP. Then click Next for viewing summary of such connection. 3. Click Finish. A page of Quick Start Wizard Setup OK!!! will appear. Then, the system status of this protocol will be shown. 4. Now, you can enjoy surfing on the Internet.
5. Customer Service If the router cannot work correctly after trying many efforts, please contact your dealer for further help right away. For any questions, please feel free to send e-mail to support@draytek.com. Be a Registered Owner Web registration is preferred. You can register your Vigor router via https://myvigor.draytek.com. Firmware & Tools Updates Due to the continuous evolution of DrayTek technology, all routers will be regularly upgraded.
