Safety Instructions

ManualsBrandsDraperies.com ManualsElectronicsTubular motor

SAFETY NOTE

1, This appliance can be used by children aged from 8 years

and above and persons with reduced physical, sensory or

mental capabilities or lack of experience and knowledge

if they have been given supervision or instruction

concerning use of the appliance in a safe way and

understand the hazards involved.

2, Children shall not play with the appliance.

3, Cleaning and user maintenance shall not be made by

children without supervision.

4, If the supply cord is damaged, it must be replaced by the

manufacturer, its service agent or similarly qualified

persons in order to avoid a hazard.

5, WARNING: the drive shall be disconnected from its

power source during cleaning, maintenance and when

replacing parts.

6, The instructions shall state that the A-weighted emis

sion sound pressure level of the drive is equal to or less

than 70 dB(A), e.g. by writing LpA ≤ 70 dB(A).

7, The mass and the dimension of the driven part shall be

compatible with the rated torque and rated operating

time.

8, The type of driven part the drive is intended for.

9, WARNING: Important safety instructions. It is important

for the safety of persons to follow these instructions.

Save these instructions.

10, Do not allow children to play with fixed controls. Keep

remote controls away from children

11, Frequently examine the installation for imbalance and

signs of wear or damage to cables and springs. Do not

use if repair or adjustment is necessary

12, Watch the moving shutter and keep people away until

he shutter is completely closed

13, WARNING: Important safety instructions. Follow all

instructions, since incorrect installation can lead to

severe injury.

14, Before installing the drive, remove any unnecessary

cords and disable any equipment not needed for

powered operation

Note: dial lithium battery switch, 0 is off switch, 1 is turn on switch.

Setting button(P1)

Lithium battery switch

5V USB charging interface

Lithium

Cell

Up button

Setting button

Stop button

Down button

Button specification

Working

Temperature

Operation note

Please read following points of attention carefully before setting.

1. Before the first use, please charge, to ensure full power after the use of(The motor uses a 5V USB

charger to charge).

①Motor stop running when the supply voltage is lower than 8.0V,and it will restart again when the

voltage is greater than 8.5V

②When the power voltage is lower than 7.0 V, the motor stops and the buzzer chirps. When the

voltage is greater than 7.5v, it can be started again.

③When the voltage is lower than 10V, when the motor is running continuously, the alarm will be

made and the buzzer will be called 10 times.

④When the power voltage is lower than 10.5 V, low voltage prompt, red light interval 1s frequency

flash, total 10 times.

⑤During the charging process, the green light flashes between 1S and 1S, and the green light is always

on after the battery voltage is greater than 12.4V, and the charging is completed.

2. Don’t operate motors when low voltage alarm

3. Operating：

①The valid interval of the emitter button is 10s,the emitter will quit the set after 10s.

②The motor will run or beep for hint,please do the next step after the hint.

4. Set the limit position：

①After the upper/lower limit setting,and the upper/lower limit position can’t at the same position.

②After the limit setting,with power off and memory function.

③Into the match-code status 2 minutes later,it will quit out the setting limits status automatically.

④Restore factory settings to clear all settings.

5. When the motor running without any operation, the maximum running time is 6 minutes,it will

stop automatically.

6. If the emitter lost,please setting up again with the new emitter.

Parameter (More models and parameters are subject to the nameplate)

One motor can store maximum 20 channels; after fully stored, if pair new channels, only the

last one wil

l be covered circularly.

Product introduction

Features:

①Driving tube must be close-fitting with crown and drive adapter.

②Choose crown and drive adapter based on the driving tube.

Motor installation

Drive tube

① Crown

② Runner

③ Circlip



READING

Tubular Motor-

BR-28-0228

Specification

(A-02)

Stroke support

Tail insert bracket

Type

Rated Torque(N.m)

The Input Voltage(V)

Rated Speed(RPM)

DM28LEU/S

2.0N.m

USB 5V 2A

Rated Power(W) 15W

28RPM

Emission Frequency(MHz)

433.92MHz

Jog & Tilt

Preferred Stop Position

Low Power Consumption

Restore Factory Setting

Built-in Receiver

Electronic Limit

Switch Direction

Stall Protection

Speed Regulation

Summary of content (3 pages)

PAGE 1
SAFETY NOTE 1, This appliance can be used by children aged from 8 years and above and persons with reduced physical, sensory or mental capabilities or lack of experience and knowledge if they have been given supervision or instruction concerning use of the appliance in a safe way and understand the hazards involved. 2, Children shall not play with the appliance. 3, Cleaning and user maintenance shall not be made by children without supervision.
PAGE 2
Stop 6 Speed Regulation P2→Up/Down→Up/Down The motor runs automatically to the 3rd limit position 1 Paring Stop If you need to reverse the rotateon of the motor controlled by the emitter,pls switch channel address. Run for hint x1 T<10s Run for hint x2 “Di” x3 T<10s 1 0 P2 Paring is OK Run for hint x1 Power off to 0 2.3, Clear the 3rd limit position “Di~” x1 Loosen P1 Press 2s 1 Press 2s Up→Up+Down Press 1s 3.
PAGE 3
FCC Warning This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. NOTE 1: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules.