USERS MANUAL SP-1001R Operating Instructions 1.INSTRUCTION MANUAL TABLE OF CONTENTS 1-1. THE USE OF PAGER 1-1-1. LCD DISPLAY OF PAGER 1-1-2. INSERTING BATTERY INTO THE PAGER 1-1-3. FUNCTION OF BUTTON 1-1-4. THE USAGE OF MODE KEY 1-1-5. THE USAGE OF PARKING TIMER 1-1-6. THE EXCHANGE OF BATTERY 1-1-7. RF RECEIVING ON/OFF 1-1-8.
1-1-9. THE OPERATION WHEN INSTALLED 1-1-10. ARM DELAY MODE 1-2. THE USE OF PAGER 1-2-1. LCD DISPLAY OF PAGER 13 1 8 2 9 3 4 5 10 11 6 7 12 • • • • • • • • ANTENNA LOW BATTERY INDICATOR DOOR LOCK DOOR UNLOCK ALERT TONE VIBRATION RF RECEIVING ON/OFF CAR SHAPE (WHEN SHOCK-SENSOR • • • • • DOOR OPEN PARKING ALARM TIMER WAKE-UP TIMER CLOCK TRUNK OPEN IS TRIGGERED, ICON BLINKING) 1-2-2.
•The receiver enters into the change of MODE with beep tone when the MODE KEY is pressed for more then 2 seconds. •The procedure for the change of MODE is as follows. • RF RECEIVING ON/OFF • SELECT OF ALERT TONE or VIBRATION • ADJUST OF CLOCK • WAKE-UP ALARM ON/OFF • ADJUST OF WAKE-UP ALARM TIME •The left button will be used when the change of MODE is required. •When the MODE-KEY is usually pressed shortly, the MODEKEY is used for the display of previous status or reset of current status. 1-2-5.
1-2-7. RF RECEIVING ON/OFF •The picture of car on the LCD will disappear when the receiver is set to OFF. •The receiver cannot receive a call when the receiver is turned OFF or the ID CODE does not match. 1-2-8. HOW TO LEARN ID •The receiver enters into the ID LEARLING mode when you press two buttons for more then 2 seconds simultaneously and then, it blinks. “Id”on the LCD. The receiver learns the ID and memorizes it if the receiver receives the transmitted signal from tramsmitter within 30 seconds.
DISAR DOOR LOCK Instant M TX MODE DOOR UNLOCK Instant TX RF ‘LOCK’ICON RF ‘UNLOCK’ICO N SINGLE BEEP DUAL BEEP 1-2-9-2. OPERATION INSTALLED WITH CAR ALARM •The transmitter enters into ARM MODE if it receives ARM INPUT from CAR ALARM and enters into DISARM MODE if it does not receive ARM INPUT.
1-2-10-1. STAND-ALONE OPERATION At the stand-alone operation, the transmitter has a 30 seconds ARM DELAY. The door-open and shock sensor do not operate during ARM DELAY. 1-2-10-2. OPERATION WITH CAR ALARM The transmitter has a 5 seconds ARM DELAY in this operation. The door lock and door unlock will operate during ARM DELAY. 1-3. INSTALLATION OF TRANSMITTER 1).Please connect all of input wires except BAT+, and then connect BAT+.
CAR ALARM. At this mode, the transmitter enters into ARM MODE by ARMEDOUTPUT being supplied from CAR ALARM. • OPERATION OF EACH INPUT When any input is sensed, the transmitter sends RF signal only once. But the transmitter does not send RF signal when the door or trunk is closed. The operation of each input is mentioned on the usage of pager. The transmitter can be used both STANDALONE and operation with CAR ALARM. 5).The receiver should do ID LEARING, after the transmitter being installed.
1-3. WIRING DIAGRAM OPERATION WITH CAR ALARM B+ B+ B+ B+ ACC IN PUT CAR CONTROLLER ALARM B+ ENGINE ON ACC INPUT ENGIN ON INPUT ARMED OUTPUT REMOTE RF ANTENNA ACC INPUT START_IN ARMED INPUT PAGER START KILL OUTPUT EXTERNAL SHOCK INPUT TRUNK INPUT DOOR UNLOCK OUTPUT DOOR LOCK OUTPUT DOOR PIN INPUT DOOR OPEN DOOR LOCK HARNESS A’SSY AND COLOR CODE 1. PIN14 : RED - +12V 4. PIN11 : BLUE – DOOR UNLOCK 7. PIN8 : WHITE – SHOCK SENSOR 10. PIN5 : PINK – HORN OUT 13.
STAND ALONE OPERATION +12V(B+) ANT DOOR LOCK INPUT DOOR UNLOCK INPUT DOOR LOCK DOOR UNLOCK DOOR PIN INPUT TRUNK INPUT B+ MAIN START KILL DOOR TX MODULE OUTPUT OPEN PIN TRUNK OPEN B+ B+ ENGINE ON START INPUT ACC SIREN OUTPU (KEY) (ARMED INPUT) HARNESS A’SSY AND COLOR CODE 1. PIN14 : RED - +12V 3. PIN12 : GREEN – DOOR LOCK 5. PIN10 : VIOLET – START IN 7. PIN8 : WHITE – SHOCK SENSOR 9. PIN6 : LIGHT BLUE – ARMED INPUT 11. PIN4 : YELLOW/BLACK – START KILL 13. PIN2: NONE 2.
DRAKE SYSTEMS ACE TECHNO 804, YANGPYUNG, YOUNGDEUNGPO , SEOUL 150-103, KOREA Tel : 82-2-2634-4700 Fax : 82-2-2634-4800 Πριντεδ ιν Κορεα
