Horizon COMPACT TM Wireless Ethernet Release 1.01.01 Product Manual - Volume 1 Version 1.
NOTICE This document contains confidential information, which is proprietary to DragonWave. No part of its contents can be used, copied, disclosed, or conveyed to any party in any manner whatsoever without prior written permission from DragonWave Inc. Copyright © 2001-2008 DragonWave Inc. Horizon Compact Release 1.01.
Table of Contents 1.0 USER MANUAL STRUCTURE ............................................................................1 2.0 INTRODUCTION TO HORIZON COMPACT ..............................................................1 2.1 A PPLICATIONS................................ ................................ ................................ ..........................2 2.1.1 2.1.2 2.1.3 2.1.4 2.2 3.0 WI MAX ...................................................................................................
Table of Contents iii 6.5.2 6.5.3 6.6 LOGGING OUT ................................ ................................ ................................ ........................ 27 6.6.1 7.0 ADDING OR CHANGING NOC U SER ACCOUNTS..................................................................... 24 ADDING OR CHANGING ADMIN USER ACCOUNTS.................................................................. 26 SESSION TIME OU T....................................................................................
DragonWave Inc. iv 11.13.1 11.13.2 11.13.3 12.0 BNC CONNECTOR ...................................................................................................... 51 TWO WIRE OPTION ..................................................................................................... 52 SINGLE WIRE OPTION WITH THE PSRM.......................................................................... 54 HORIZON MANAGEMENT ................................ ................................ ............... 57 12.
Table of Contents v List of Figures FIGURE 2-1 HORIZON COMPACT - C OPPER INTERFACE V ARIANT................................ ................................ ..5 FIGURE 2-2 HORIZON COMPACT LED INDICATORS.....................................................................................5 FIGURE 2-3 DUAL P OLARITY R ADIO MOUNT .............................................................................................7 FIGURE 3-1 HORIZON COMPACT INSTALLATION ................................................
DragonWave Inc. vi List of Tables T ABLE 2-1 HORIZON LED OPERATION .....................................................................................................6 T ABLE 2-2 PORT 2 POWER C ABLE WIRE GAUGE.......................................................................................7 T ABLE 3-1 PARTS REQUIRED .................................................................................................................9 T ABLE 5-1 USER ACCOUNT L EVELS.......................................
1.
DragonWave Inc. 2 This page left blank intentionally Horizon Compact Release 1.01.
2.0 Introduction to Horiz on Compact DragonWave’s Horizon Compact is a next-generation, high capacity, native Ethernet, microwave system offering improved economics and simplified operations. Featuring zero-footprint, the radio and the modem are integrated into one, single, compact, out-door-unit. Increased capacity (800Mbps); simplified installation and operation; and improved troubleshooting mean lower lifecycle costs.
DragonWave Inc. 2 Product Features 6 -38 GHz Frequency Support High power variants 800 Mbps full duplex capacity 100ms Adaptive Modulation Transparent Gigabit Ethernet solution 100ms Ring/Mesh Switching Integrated RF Loopback “Zero-footprint”, hardened outdoor unit 2.1 2.1.1 Applications WiMax DragonWave offers a high-capacity, carrier-grade, integrated solution for Ethernet backhaul using interference-free licensed spectrum.
Introduction to Horizon Compact 3 2.2 Technical Specifications Frequencies 6 GHz 7 GHz 8 GHz 11 GHz 13 GHz 15 GHz 18 GHz 23 GHz 24 GHz 24 GHz 26 GHz 28 GHz 38 GHz FCC/IC/ETSI/ITU/AUS/NZ/ RUS ETSI/ITU/NZ/MEX IC/ETSI/ITU/UK/NZ/RUS FCC/IC/ETSI/ITU ETSI/AUS/NZ/ITU IC/ETSI/AUS/NZ/MX/ITU FCC/IC /ETSI/AUS/NZ/ITU FCC/IC/ETSI/AUS/NZ/ITU/MX UL FCC/IC/ETSI DEMS FCC/IC ETSI FCC/ETSI FCC/ETSI/AUS/NZ/MX Mechanical Radio/Modem (w/o antenna) 12 cm x 23.6 cm x 23.6 cm; 4.8kg (4.75 in x 9.3 in x 9.3in; 10.
DragonWave Inc. 4 This page left blank intentionally Horizon Compact Release 1.01.
3.0 Physical Description Horizon Compact is an integrated Ethernet modem and microwave radio transceiver, housed in a rugged weatherproof housing. It is provided with two weatherproof connectors, Port 1 and Port 2. Port 1, copper 10/100/1000 Base-t, or optional optical interface, carries data and optional in-band management traffic. Port 2, copper 10/100/1000 Base-t, carries optional out-of -band management traffic only . When Port 2 is not in use, a weatherproof protective cap is used to seal the port.
DragonWave Inc. 6 Table 3-1 Horizon LED Operation LED Status Description RF/Modem LED RED Slow RED Blink Steady GREEN/slow ORANGE blink Steady GREEN Power ON, FPGA not ready. RF Transmitter OFF. Modem LOS RF Transmitter ON. Modem LOS. RF Transmitter ON. Modem OK. Ethernet LED Copper Mode OFF Slow Red Blink Steady Green Fast Green Blink Fiber Mode OFF (future release) Steady Red Slow Red Blink Steady Green Fast Green Blink No link detected on either Ethernet port.
Physical Description 7 As an alternative, an existing AirPair ODU composite power and Ethernet cable assembly, which is compatible with the Horizon Port 2 connector, may be used, provided that the RJ-45 connector (grey CAT5) at the Transtector end is re-terminated to A T & T GigE standards . The same Transtector type used in an AirPair ODU installation may also be used.
DragonWave Inc. 8 3.4 Power Switch Radio Mount (PSRM) For redundancy purposes, the PSRM allows two Horizon units to be mounted to a single antenna. Both units must be oriented for the same polarity and only one unit can transmit/receive at any one time. The PSRM looks similar to the DPRM shown in Figure 3-3, but has internal components that only allow one unit to transmit/receive at a time. Note that redundant systems do not have to use the PSRM.
4.0 Installation Requirements Various installation kits are available.
DragonWave Inc. 10 Horizon PonE/surge arrestor (copper interface) or Transtector (optical interface) Figure 4-1 Horizon Compact Installation 4.1 Hoisting Lug A hoisting lug is shipped with each Horizon Compact (two per link). Th is can be bolted onto the horizon with the supplied bolt, using any of the available threaded holes, and used for attaching a line for hoisting or carrying the unit into position on a tower or pole. Figure 4-2 shows how the lug is attached.
Installation Requirements 11 4.2 Ethernet Cabling from Horizon to Ethernet Switch For the copper interface, data cabling from the Horizon unit to the Ethernet switch consists of outdoor rated, shielded, Cat5E cables equivalent to Belden 7919A. The shielded cables require shielded RJ-45 connectors. Use of standard indoor unshielded RJ-45 connectors may result in poorly constructed cables, intermittent connections and data loss.
DragonWave Inc. 12 4.3 Assembling the RJ-45 Connector Weatherproof RJ-45 connector shells are used for connecting the CAT5E cable, leading from the poweron- Ethernet power supply and network connections, to the Horizon Compact. Cables and connectors may be purchased from DragonWave or may be constructed or supplied by the customer. Two different styles of connector have been used in production. For Horizon serial numbers ending in “999” or less, an RJ45 “snap in” type in-line housing is used.
Installation Requirements 13 4.3.2 “Push fit” style This connector relies on a gland nut to hold the assembly firmly together. The CAT5E cable is threaded through all the components of the connector housing (see Figure 4-5) before the cable is terminated as a straight through connection with a shielded RJ-45 connector. Once terminated, the RJ-45 connector slides back into the connec tor housing which accepts the tab on the RJ-45 connector.
DragonWave Inc. 14 This page left blank intentionally Horizon Compact Release 1.01.
5.0 Powering the Horizon Compact Before an active management session can be started on the Horizon Compact, power needs to be provided to the unit. Read this section completely before applying power to the Horizon Compact. 5.1 Copper Interface The Horizon Compact with copper interface receives its power over the Ethernet connection to Port 1 using a DragonWave proprietary technique. To integrat e the power onto the Ethernet cable requires the use of the DragonWave Power on Ethernet ( PonE) adapter.
DragonWave Inc. 16 5.2 Optical Interface In the copper interface version, power is fed to the Horizon using PonE techniques via the Ethernet connection to Port 1. In the optical version, this is not possible, so power is fed via the connection to Port 2. Port 2 on the optical interface variant is equipped with a weatherproof MIL style multi- pin connector, which incorporates an Ethernet connection and a power feed (NOT PonE) connection.
Installation Requirements 17 1000BaseTx – RJ-45 pinout Pin Signal Color 1 TP0+ White/Green 2 TP0- Green 3 TP1 + White/Orange 4 TP2+ Blue 5 TP2- White/ Blue 6 TP1- Orange 7 TP3+ White/Brown 8 TP3- Brown Figure 5-3 RJ-45 connector pinout – Port 2 management Horizon Compact Release 1.01.
DragonWave Inc. 18 This page left blank intentionally Horizon Compact Release 1.01.
6.0 Initial Configuration There are a number of configuration steps that need to be carried out before the Horizon Compact can become operational. It is recommended that these steps be performed prior to mounting the system on the tower. These steps relate to: • radio bands • frequency channels • IP address information Once this information has been correctly entered, the Horizon Compact system is ready for installation and system alignment.
DragonWave Inc. 20 6.1.3 Using the Web interface The Horizon Compact Web interface is disabled by default. You must use Telnet to enable the Web interf ace by issuing the CLI command set web server on press Enter. Open a Web browser and, in the “Address” or URL field at the top of the page, enter the IP address of the Horizon unit (default is 192.168.10.100) and press Enter. If your laptop or PC has been correctly set up, you will be prompted for the user name and password.
Initial Configuration 21 6. To reduce the throughput speed to a figure less than the licensed speed, use the CLI command set system speed , where is in Mbps and can be adjusted in 1 Mbps increments. 7. Type the CLI command get frequency bank and press Enter. A list of frequencies is displayed. 8.
DragonWave Inc. 22 6.3 Configuring IP Address Values When shipped from DragonWave, the Horizon Compact is configured with a default IP address (192.168.10.100) and subnet mask (255.255.0.0). The default address is used to communicate with the Horizon Compact for initial configuration purposes, such as entering the IP address that the unit will have in the network to which it is to be connected. IP address information is entered in the following manner: 6.3.1 Using Telnet 1.
Initial Configuration 23 6.4 Recovery of IP Address and Serial Numbers In the event that the Horizon Super User name and password, or IP address has been lost, forgotten, or misconfigured, you will need to contact DragonWave.
DragonWave Inc. 24 6.5.2 Adding or Changing noc User Accounts Up to five noc user accounts can be configured. Use the CLI command set noc user as shown in the following procedure: Required Action Steps Create noc Login Accounts Five noc (network operations center) accounts are available. username and password cannot be the same value. The Log in as the super user. View current account settings.
Initial Configuration 25 Required Action Steps Enter the desired username for this account. The system responds: Verify UserName: Re-enter the desired username for this account. The system responds: Password: Enter the desired password for this account. The system responds: Verify Password: Re-enter the desired password for this account. The system responds: User Accepted: If the usernames or passwords do not match the system will respond: nak Repeat for as many noc accounts as required. Save the settings.
DragonWave Inc. 26 6.5.3 Adding or Changing Admin User Accounts Up to 50 admin accounts can be configured. Use the CLI command set admin user as shown in the following procedure: Required Action Steps Create Administrator Login Accounts 50 Administrator accounts are available. The username and password cannot be the same value. Log in as the Super User View current user account settings.
Initial Configuration 27 Required Action Steps Re-enter the desired username for this account. The system responds: Password: Enter the desired password for this account. The system responds: Verify Password: Re-enter the desired password for this account. The system responds: User Accepted: If the usernames or passwords do not match the system will respond: nak Repeat for as many admin accounts as required. Save the settings. save m ib press Enter The system responds: MIB saved.
DragonWave Inc. 28 This page left blank intentionally Horizon Compact Release 1.01.
7.0 Antenna Mounting and Tower Specifications The Horizon Compact unit clip mounts onto a range of antennas, providing a variety of gain and range options. The same mounting system is used for all sizes of antenna. The Horizon Compact has four, integral, spring loaded, mounting clips. The antennas are provided with four mounting lugs, onto which the mounting clips attach.
DragonWave Inc. 30 The radio frequency polarity is indicated by an arrow molded into the Horizon Compact housing. Attach the Horizon Compact to the antenna so that the arrow points either vertically or horizontally, as required, when the assembly is attached to the mounting post or tower. With the arrow horizontal (pointing to the left) – horizontal polarity; with the arrow vertical (pointing upwards) – vertical polarity.
Installation Requirements 31 7.1.2.1 UL24 Antenna Information This dev ice has been designed to operate with the antennas listed below, and having a maximum gain of 43.7 dBi. Antennas not included in this list or having a gain greater than 43.7dBi are strictly prohibited for use with this device. This device has integrated antennas. 24UL Antenna Data Andrews VHLP1-26DW Andrews VHLP 2-26DW Andrews VHLP 2.5-26DW 1 foot 2 foot 2.5 foot 7.2 36.2dBi 40.8dBi 43.
DragonWave Inc. 32 7.3 Pole and Tower Specifications It is important that mounting posts or towers used meet the DragonWave specifications for rigidity to minimize the effects of twist and sway on the alignment of the link. Note that the maximum twist and sway angle allowable is equal to half of the antenna beam width.
Installation Requirements 33 Horizon Compact Release 1.01.
8.0 Grounding, Power and Surge Arrestors The Horizon unit must be grounded using a minimum of 6 AWG copper wire attached to any of the eight ground points available on the Horizon case, as shown in Figure 8-1. Surge arrestors and lightning protection is built into the Horizon unit. The Ethernet and PonE cables must be properly protected at the end of their run as they enter the building. Before Ethernet cables enter buildings, voltages shall be clamped down to SELV by approved type primary protectors.
Grounding, Power and Surge Arrestors 35 8.1 Power on Ethernet (PonE) The copper interface variant of Horizon operates on -48 VDC and employs a proprietary Power on Ethernet solution. The Horizon Power on Ethernet surge arrestor unit provides integration of - 48 VDC and the two straight through Ethernet cables. Note:The Horizon PonE implementation is proprietary and does not follow IEEE standards.
DragonWave Inc. 36 Grounding point Redundant power terminals (-48 VDC) To Horizon Compact (Power on Ethernet) Power cable clamps To network (protected) Ethernet cable clamp CAUTION CONNECT ONLY TO HORIZON DO NOT CONNECT TO NETWORK Figure 8-2 Surge arrestor and power integrator Two different siz ed cable clamps are provided for the power cable. Select the one that best suits the size of cable being used. The Ethernet cables are secured with a “bar” type clamp which is locked down using a single screw.
Grounding, Power and Surge Arrestors 37 This page left blank intentionally Horizon Compact Release 1.01.
9.0 Preparing for Alignment The Horizon Compact and antenna assembly is attached to the mounting post, or tower, with a specialized mounting bracket that allows fine orientation adjustment of the Horizon/antenna assembly. The same mounting bracket is used for all antenna sizes. Visual alignment is achieved by rotating the assembly on the post, or tower, and positioning the assembly so that the antenna is visually aligned with the target system before tightening the mounting bracket clamp.
Preparing for Alignment 39 9.1 Received Signal Level (RSL) Measurements To accurately align the Horizon Compact to its far end peer, you need to monitor the received signal level (RSL). There are two recommended methods for monitoring RSL. These are: 1. Use the CLI command set alignment on to activate the alignment feature at the BNC connector located on the side of the unit. Connect a voltmeter to the BNC connector. The voltage at this connector is linearly related to RSL and is 1 mV per dB e.g.
DragonWave Inc. 40 9.2 Three Important Factors When you prepare to align the radio antennas , you must consider three important factors: 9.2.1 1. the radiation patterns of dish antennas (main lobe and side lobes) 2. the need for a Clear Line of Sight (LoS) 3.
Preparing for Alignment 41 This page left blank intentionally Horizon Compact Release 1.01.
10.0 Aligning the Antennas Follow the steps of the alignment procedure shown below . Note: ensure that the CLI command set alignment on has been entered at both ends of the link if you are using the BNC connector to measure field strength. At the first end: 1. Loosen the pan mechanism lock nuts 2. Pan or move the antenna horizontally across the entire range of adjustment to identify the main lobe and the side lobes.
Preparing for Alignment 43 10.1 Signs of a Healthy Link You can be confident that a link is properly aligned and free of problems if the following readings are obtained during a Telnet or Web interface session with each end of the link : • No alarms – use the CLI command get alarms and press Enter to return a list of current alarms – should be none that cannot be explained by network status • Received signal level (RSL) within ±3 dB of link budget figure in clear weather.
11.0 Advanced Configuration Features DragonWave Horizon Compact has a number of optional advanced configuration features that may be applied if desired. It is recommended that they only be applied once the Horizon Compact is satisfactorily aligned and successfully carrying traffic. The following lists the features available: • Radius Server User Authentication • Threshold Alarms • VLAN Tagging • Rapid Link Shutdown (RLS) • 802.
Advanced Configuration Features 45 11.2 Management VLAN Tagging Note: The configuration of Horizon Compact VLAN tagging is only necessary if you wish to restrict Horizon Compact management communications to a specific management VLAN. The Horizon Compact system will pass user VLAN traffic transparently, independent of the Horizon Compact VLAN settings. The VLAN settings are for Horizon Compact management purposes and do not affect user data or traffic. VLAN Standard IEEE 802.
DragonWave Inc. 46 11.3.1 Operation with 802.1P Priority Queuing Disabled If 802.1P filtering is disabled in the Horizon Compact system, all incoming frames are treated equally and are forwarded on a first -come first-served basis. The system operates in a FIFO (First In First Out) basis. If the Pause Frames feature (see Section 11.4) is enabled, pause frames will be sent to the connected switch when the input buffer is close to being full (internally set threshold).
Advanced Configuration Features 47 Frames destined for the 01-80-C 2-00-00-xx MAC addresses are sent to the internal Queue. Examples: STP, RSTP, MSTP LACP, Pause Frames, GARP (GMRP,GVRP), bridge broadcasts, OAM, LLDP, Port based authentication are all sent to the internal Queue and are transmitted in an expedited fashion.
DragonWave Inc. 48 Note: The average packet throughput is calculated using 64, 128, 256, 512, 1024, 1280, and 1518bytes Ethernet frames. ** Throughput optimized to fit within required spectral mask limits. 11.6 Adaptive Transmit Power Control (ATPC) Adaptive Transmit Power Control (ATPC) allows a Horizon Compact system to adjust its transmit power to compensate for far end signal loss caused by changes in atmospheric conditions e.g. heavy rain.
Advanced Configuration Features 49 11.7 Horizon Compact Authentication This feature is only necessary if you wish to restrict communication from a Horizon Compact unit to a specific peer or to a group of Horizon Compact units. Authenticat ion is generally used as a security measure. It is not recommended to enable Authentication prior to alignment of the radios.
DragonWave Inc. 50 11.8 Threshold Alarms Horizon Compact provides Threshold Alarms to assist in managing the performance of the system. Threshold alarms are available for the following parameters: 1. 2. 3. 4. RSL (Receive Signal Level) Bandwidth Utilization Dropped Frames Signal To Noise (SNR) * With the exception of SNR, each Threshold Alarm has two associated parameters: 1. Threshold value 2. A time limit over which the Threshold value must be exceeded before the alarm is reported.
Advanced Configuration Features 51 Table 11-2 Time Sources Source IP Address Index Stratum Source 1 2 199.212.17.15 Industry Canada 2 2 199.212.17.20 Industry Canada 3 1 192.5.41.40 U.S. Navy 4 1 192.5.41.209 U.S. Navy 5 2 129.132.2.21 Switzerland 11.11 Automatic Adaptive Modulation (AAM) The two principal modulation schemes used on the Horizon Compact system are QPSK and QAM. QPSK (the lowest modulation scheme) is ideal for long distance, but has the lowest throughput capability.
DragonWave Inc. 52 11.12 Horizon Compact Throughput Doubling Horizon units are capable of transmitting up to 400 Mbps. For higher data rates, an Ethernet switch that supports link aggregation is required. Horizon can be configured as 2 units, each with their own separate antenna, or the Dual Polarity Radio Mount (DPRM) can also be used to mount two systems to a single antenna (see Figure 3-3).
Advanced Configuration Features 53 in a hot stand-by state. When the DC signal is removed (as a result of the unit normally carrying traffic failing), then the stand-by radio becomes active, and takes over the traffic. After a redundancy switch, once the first system is able to return to carrying traffic, a manual switch is required, via a CLI command, to return the system to its original state. 11.13.
DragonWave Inc. 54 Figure 11-3 Redundancy Connections – 2 wire option – optical interface NOTE: For clarity, the Transtector surge arrestor has been omitted from the diagram. Both the Ethernet management feed to Port 2 and the power feed, via Port 2, must be protected from transients. Horizon Compact Release 1.01.
Advanced Configuration Features 55 11.13.3 Single Wire Option with the PSRM The “single wire” option is so named because only one data feed is required to be connected to the two interconnected Horizon systems mounted on the PSRM. The PSRM supports s ystem redundancy by connecting two Horizon units to a single antenna. Only one of the radios of the mounted systems may operate at any one time. Both systems have the identical polarity, either both vertically or both horizontally polarized.
DragonWave Inc. 56 Figure 11-5 Redundancy Connections – Single wire option – optical interface NOTE: For clarity, the Transtector surge arrestor has been omitted from the diagram. The power feed must be protected from transients. Horizon Compact Release 1.01.
Advanced Configuration Features 57 This page left blank intentionally Horizon Compact Release 1.01.
12.0 Horizon Management The Horizon Compact system can be fully managed locally or remotely. Horizon Compact supports Telnet access, SNMP management and a Web interface accessible through the IP network. The entire Command Line Interface (CLI) command set is available through Telnet. The entire list of system parameters is available through SNMP access. The Web interface provides access to system configuration and performance parameters. In-band and out -of -band management options are available. 12.
Horizon Management 59 12.1.2 Management through Port 2 (out-of-band) Port 2 is available for out-of-band management purposes only. It does not carry customer data traffic. It has been designed to be used in conjunction with a management overlay network that is separate from the customer data network. The management overlay network is typically extended back to the Network Operations Center. To select out -of -band management use the CLI command set network management interface port2 and press Enter.
DragonWave Inc. 60 SNMPv3 is an interoperable standards-based protocol that provides secure access to devices by authenticating and encrypting packets over the network. The security features provided in SNMPv3 are as follows: • • • Message integrity Authentication Encryption Formatted: Font: 8 pt, Bold Formatted: Font: 8 pt, Bold SNMP configuration is covered in detail in Volume 2. 12.
Horizon Management 61 Sub -menu Options The main screen has four Sub-menu options : 12.5.2 • More Information - opens a window and displays a summary of the system configuration. • System Name - link to the System Configuration page. If this field has been previously configured then the value is displayed • System Location - link to the System Configuration page.
DragonWave Inc. 62 12.5.5 Alarms Screen The Alarms screen displays the current status of the alarms withi n the Horizon Compact system and the total accumulated time the alarm has been present (in seconds). The total accumulated time may indicate the current alarm has been active for the timeframe indicated, or may indicate the alarm has occurred multiple times for a total time equaling the displayed value (See 12.9 for a list of alarms) .
Horizon Management 63 12.7 Event and Performance Logs The Horizon Compact system supports two logs, the Events Log and the Performance Log. Each can be used to trace the behaviour of the system over time. The Events Log is invoked or disabled by issuing the CLI command set logging [on/off] . This log records alarm and reset events. Approximately 17,500 events can be captured by the Events log. Once the log is full the oldest entries are overwritten.
DragonWave Inc. 64 12.9 Alarms List Use the CLI command get alarms to display a list of active alarms. Alternatively, alarms are listed on the Alarms page of the Web interface. Active alarms are clearly indicated.
Horizon Management 65 This page left blank intentionally Horizon Compact Release 1.01.
13.0 Configuration Backup and Restore Horizon Compact provides a backup and restore facility for system configuration data and user account data. The backup and restore uses an FTP server to tr ansfer files. It is recommended to have an FTP server at your network management site for use with the Horizon Compact backup and restore facilities. Note that the Super User or a noc user level can perform backup and restore functions. 13.
Horizon Management 67 This page left blank intentionally Horizon Compact Release 1.01.
14.0 Software Upgrades From time to time new software loads are made available that may add new features to the Horizon Compact system. You can download new software remotely using File Transfer Protocol (FTP). Use the Command Line Interface (CLI) via Telnet and invoke the FTP with either a local FTP server that is on the same network as the Horizon Compact system, or use DragonWave’s FTP server site available through the Internet.
Horizon Management 69 This page left blank intentionally Horizon Compact Release 1.01.
Appendix A – List of CLI Commands Command Syntax Summary (alpha order) ? (help) copy [ftp:filename] create ssl certificate delete mib [newest|both] delete radius server [index] diagnose aam downgrade system licensed speed [speed] erase log erase performance log exit get aam status get alarms get alarms counter get alignment get air interface authentication type get antenna diameter get atpc status get authentication failure action get authenticated peer get authentication status get backup ipconfig get band
Appendix A get system redundancy get telnet access get traffic statistics get transmit power get unique peer authentication key get user accounts get user session get vlan tag get vlan tagging get web server kill ssh sessions list [ftp:file/directory/] lo ping [-w timeout][-n count][-t][ip address] reset [system / modem] save config [ftp:filename] save log [ftp:filename] save mib save performance log [ftp:filename] save users [ftp:filename] set aam [on/off] set admin user set air interface authentication t
Appendix B – Safety Information Safety Information for Radio Equipment The Federal Communications Commission (FCC), with its action in ET Docket 96-8, has adopted a safety standard for human exposure to radio frequency (RF) electromagnetic energy emitted by FCC-certified equipment. DragonWave Horizon Compact meets the uncontrolled environmental limits found in OET- 65 and ANSI C95.1, 1991.
Appendix C 73 Professional Installation DragonWave Horizon Compact devices require professional installation. It is the responsibility of the installer to be sure that all building and safety codes are met and that the installation is complete and secure. The Horizon Compact shall be installed according to local Electrical Safety Codes. For Canadian installations, the entire equipment installation must comply with Canadian Standard CSA 22.2, No. 60950, Safety of Information Technology Equipment.
DragonWave Inc. 74 Electrocution Hazard Warning Electrocution Hazard This product is intended to be conn ected to a –36 to -60V DC power source (power adapter supplied by DragonWave Inc.), which must be electrically isolated from any ac sources and reliably connected to Earth ground. Do not install DragonWave products near any type of power line.
Appendix C 75 This page left blank intentionally Horizon Compact Release 1.01.
Appendix C - Regulatory Compliance Information This section contains information regarding regulatory compliance with the Federal Communication Commission, Department of Communications and the European Telecommunications Standards Institute applies to the Horizon Compact radio link. Federal Communication Commission Declaration of Conformity Statement This device complies with Part 15 of FCC Rules. Operation is subject to the following two conditions: 1.
Appendix D 77 Department of Communications – Canada - Compliance Statement This class B Digital apparatus meets all the requirements of the Canadian Interference- Causing Equipment Regulations. This device complies with RSS-210 of Industry Canada. conditions: Operation is subject to the following two 1. this device can not cause harmful int erference; and 2. this device must accept any interference received, including interference that can cause undesired operation.
DragonWave Inc. 78 This page left blank inte ntionally Horizon Compact Release 1.01.
Appendix D 79 Copyright © 2000-2007 DragonWave Inc. Printed in Canada. All rights reserved. Horizon Compact™ Product Manual, 83- 000027-01-01-0 4 Visit us on the Internet at: http://www.dragonwaveinc.com/ Horizon Compact Release 1.01.
