Installation Instructions

ManualsBrandsDräger ManualsElectronicsInductive Charger

Dräger X-am

3500/8000 and

Inductive Power Unit

Edition 03 - January 2019 - 90 33 655

Approvals / Marking

X-am 3500

X-am 8000

Serial No.

Dräger X-am 3500/8000 and Inductive Power Unit

Only for USA:

Changes or modifications not expressly approved by the party

responsible for compliance could void the user's authority to

operate the equipment.

This equipment has been tested and found to comply with the

limits for a Class B digital device, pursuant to part 15 of the

FCC Rules. These limits are designed to provide reasonable

protection against harmful interference in a residential installa-

tion. This equipment generates, uses and can radiate radio fre-

quency energy and, if not installed and used in accordance

with the instructions, may cause harmful interference to radio

communications. However, there is no guarantee that interfe-

rence will not occur in a particular installation. If this equipment

does cause harmful interference to radio or television recepti-

on, which can be determined by turning the equipment off and

on, the user is encouraged to try to correct the interference by

one or more of the following measures:

 Reorient or relocate the receiving antenna.

 Increase the separation between the equipment and recei-

ver.

 Connect the equipment into an outlet on a circuit different

from that to which the receiver is connected.

 Consult the dealer or an experienced radio/TV technician

for help.

This device complies with part 15 of the FCC Rules. Operation

is subject to the following two conditions:

(1) This device may not cause harmful interference, and

(2) this device must accept any interference received, inclu-

ding interference that may cause undesired operation.

FCC responsible party:

Draeger Inc.

7256 S. Sam Houston W. Parkway

Suite 100

Houston, Tx 77085 USA

phone: +1 346-802-6111

e-mail: DIHouston.Approvals@draeger.com

Only for Canada:

CAN ICES-3 (B)/NMB-3(B) - only for Dräger X-am 3500/8000

Only for CSA (Canadian Standards Association):

WARNING: Wireless communication is intended for use as a

secondary remote alarm status notification only. Primary

alarming of combustible gas hazards is provided locally by de-

tector.

WARNING: Applicable to CLASS II DIV.1, GROUPS E, F, and

G certification: CSA Std. 152 does not have any requirement

for Class II environment and therefore this device has not been

performance tested for Class II hazardous location. The sen-

sor may become clogged and not detect gas properly or warn

the user of its inability to detect gas.

AVERTISSEMENT: La communication sans fil est destinée à

être utilisée uniquement comme notification d'état d'alarme se-

condaire à distance. L'alarme primaire des risques de gaz

combustible est fournie localement par le détecteur.

AVERTISSEMENT: Applicable à la certification CLASSE II

DIV.1, GROUPS E, F et G: CSA Std. 152 n'a pas d'exigence

pour l'environnement de classe II et par conséquent, cet appa-

reil n'a pas été testé pour un emplacement dangereux de Clas-

se II. Le capteur peut se boucher et ne pas détecter

correctement le gaz ou avertir l'utilisateur de son incapacité à

détecter le gaz.

1) The year of manufacture is indicated by the third letter in the serial

number: K = 2017, L = 2018, M = 2019 etc. Example: Serial No.

ARKH-0054: the third letter is K, which means that the unit was

manufactured 2017.

Type: HFG 0000

P/N: XXXXXXX

S/N: ARXX-XXXX

Use only power supply

Dräger LBT 02**

X-am 3500

0158

I M1 / II 1G

Ex da ia I Ma

Ex da ia IIC T4 Ga

BVS 17 ATEX E 040 X

IECEx BVS 17.0034X

&7D&

18.70148494

Class I, Zone 0, A/Ex da ia IIC T4 Ga

Class II, Div. 1, Groups E, F, G

C22.2 No. 152 for comb. sensors, Class I only

data

matrix

code

Type: HFG 0010