DTP-800/DTP-1900 Operating Manual 1. Introduction Thank you for purchasing this product. Please check whether the product package contains the following items. If there are missing items, please call the service center. 1. Phone 2. Power Supply(SMPS) 3. Antenna 4. Installation Panel 5. User’ s Manual 6. Power Cord 7.
DTP-800/DTP-1900 Operating Manual 1.1 Installation Procedure ① Connect the DC jack to the back panel of phone as shown in the figure below. ② Connect the plug of the SMPS to a power outlet and to SMPS for the phone. ③ Turn power on by moving the switch button to the right as shown following figure, and then the phone is initialized with power-up sound.
DTP-800/DTP-1900 Operating Manual ④ Adjust the antenna direction until the maximum Antenna power sign is displayed on the LCD screen. (Each bar indicates the received signal strength. The more bars mean the higher signal strength, the better service condition.) ☞ See 2.1 Power-Up / Power-Down 1.2 Installation of the Wall Bracket Before finalizing the precise location of the phone, please perform the signal strength test to find the best location after the unit is assembled.
DTP-800/DTP-1900 Operating Manual 1.3 Panel Overview LCD Antenna Menu Button Up/Down Button STORE Button DND/MUTE & RCL Button MSG/VAS & Clear Button Earpiece Dial Button SND/RDL Button Speaker Button Microphone Figure: 1.
DTP-800/DTP-1900 Operating Manual Antenna RF Connector Power Switch DC Power Jack Figure : 1.
DTP-800/DTP-1900 Operating Manual 1.4 Safety Instructions Basic safety precautions should always be followed to reduce the risk when using this unit. · · · · · · · · · · · Read and follow all instructions marked on the product. Do not disassemble this unit to reduce the risk of electric shock. When the unit is subsequently used, incorrect reassembly can cause electric shock. When service is required take the unit to an authorized service center. Do not hold or contact the antenna while a call.
DTP-800/DTP-1900 Operating Manual 2. Before Using 2.1 Power-Up / Power-Down 2.1.1 General Power-Up ① Manufacturer’ s logo will be displayed for 1 second when the power is turned on. Figure : 2.1.1 - 1 ② The screen (figure 2.1.1-2) will be displayed with the power-up sound. DOWTEL WIRELESS PHONE Figure : 2.1.1 - 2 ③ If the phone receives the signal from the Service Provider, the screen displays the default date and time set by factory. (figure 2.1.1-3) Nov 11 (Sun) 11:11 am Figure : 2.1.
DTP-800/DTP-1900 Operating Manual 2.1.2 No Service If “ No Service” message is appeared like the figure 2.1.2, the location where the phone is installed may be the area of which the signal from the Service Provider is not delivered to the phone. If the number of bar beside the Ant. symbol on the screen in figure 2,1,13 is small, it means the received signal strength is weak. < Reference 2.3.1 RSSI Icon> No Service Fig ure : 2.1 .
DTP-800/DTP-1900 Operating Manual 2.1.4 Power Two types power is used in this phone. - AC power : 100 ~ 270 V - Internal Battery If the AC power is suddenly disconnected to the phone by a power failure or any reason, the power source is automatically changed from AC power to internal battery. When the status of power switch of the phone is turned on, the phone normally works as long as you disconnect the AC power. If you don’ t want the power entirely, you must turn off the power switch.
DTP-800/DTP-1900 Operating Manual 2.2 Keypad As shown in the figure below, there are 12-Dial Button and 10-Function Button in this phone. DND/MUT E MSG/V AS MENU S T ORE RCL CLR 1 2ABC 3DEF 4GHI 5JKL 6MNO 7PQRS 8T UV 9 WXYZ * 0OPER # SPK SND/RDL Figure : 2.2.1 2.2.1 DND/MUTE & RCL DND/MUT E RCL DND/MUTE - Use this button to set on/off the [DND(Do Not Disturb)] function if you don’ t want to answer the incoming call in idle-state. (Reference 3.
DTP-800/DTP-1900 Operating Manual DND/MUTE & RCL and MSG/VAS & CLR buttons are designed as an one -button as shown in figure 2.2.1. But these buttons separately operate the upper side and bottom side of the button to work their own function. 2.2.2 MENU Use this button to set the [MENU] mode or return to Idle-state. MENU 2.2.3 UP / DOWN Use this button to set the [MENU] mode, adjust the ringer and voice volume, and store/find the phone number in the Phone Book. 2.2.
DTP-800/DTP-1900 Operating Manual 2.2.5 MSG/VAS & CLR (Clear & Recall) MSG/V AS CL R MSG/VAS - Use this button if you want to retrieve the text message of SMS(Short Message Service) transmitted and received during the idle-state. - Use this button to make a call to VMC(Voice Message Center) direct to retrieve the voice mail after picking up the handset or setting the speakerphone on.
DTP-800/DTP-1900 Operating Manual 2.2.8 Dial Button(0~9, * , # ) - Use this button to store the phone number - There are small alphabets beside the numeric number on the each Dial Button. It is used to store the name related with the phone number when you want to store the phone number. If you want to store “ DOWTEL3” , follow below procedure.
DTP-800/DTP-1900 Operating Manual 2.3 ICON The various icons are displayed in the first line on the LCD screen to indicate the setting-status and operating-status of the phone. 2.3.1 RSSI Icon - Indicate the strength of received signal. It is closely related with the quality of service. - There are 5 bars with different length. It is the best condition if all bars are displayed beside the Antenna. symbol. - When there is only 1-bar on the screen, it means poor service condition.
DTP-800/DTP-1900 Operating Manual 2.3.4 Speaker Phone Icon - Indicate the phone is in Speaker Phone Mode. - It is displayed when you attempt to make a call using the speaker and microphone. 2.3.5 Voice Mute Icon - Indicate the status that the user’ s voice, any surrounding sounds, and keypad tone are not transmitted to the calling party. - When you set this function on during a conversation, No sound will be transmitted. 2.3.
DTP-800/DTP-1900 Operating Manual 2.3.8 Battery Icon - Indicate the strength of the battery installed inside the phone - The battery strength is displayed 5-step. - When the battery strength is weakening, the phone beeps to request the recharge of the battery. 2.3.9 DND (Do Not Disturb) Icon - Indicate the status that user set DND function on to deny the incoming call when user don’ t want to answer the incoming call. - During this icon is flashing, the phone doesn’ t answer to the incoming call. 2.3.
DTP-800/DTP-1900 Operating Manual 2.4 Sound & Tone 2.4.1 Power-up Sound When you turn on the power of the phone, The phone starts with the beepsound. 2.4.2 Dial Tone This sound indicates that the phone is able to connect with the system and you can make or receive a call 2.4.3 Warning Tone When the phone is unable to connect with the system or the handset is incorrectly placed on the phone, it beeps through the handset or speaker. 2.4.
DTP-800/DTP-1900 Operating Manual 2.4.9 SMS/VMS notification tone It beeps through the speaker when the phone is received the SMS or VMS message. 2.4.10 Error Beep Tone It beeps when the user push the keypad incorrectly. incorrect operating is ignored.
DTP-800/DTP-1900 Operating Manual 3. Basic Function 3.1 Making Calls 3.1.1 Using the Handset Nov 11 (Sun) 11:11 am ▶ Pick up the handset and dial the phone number you want to make a call. 1001234 ▶ Press the [SND/RDL] button . Connecting… 1001234 ▶ The call is connected.
DTP-800/DTP-1900 Operating Manual 3.1.2 Using the Speaker Phone ▶ Press the [SPK] button and dial the phone number you want to make a call. 1001234 ▶ Press the [SND/RDL] button. Connecting… 1001234 ▶ The call is connected.
DTP-800/DTP-1900 Operating Manual 3.1.3 On-Hook Dialing ▶ Dial the phone number, and then press the [SND/RDL] button. Connecting… 1001234 (figure 3.1.3- 1) ▶ The speaker phone operates automatically, and then the call is connected. 00:01 1001234 (Figure 3.1.3- 2) 3.1.4 Redial the Last Number called ▶ Pick up the handset or press the [SPK] button, and then press [SND/RDL] button. Connecting… 1001234 (Figure 3.1.
DTP-800/DTP-1900 Operating Manual ▶ The last number dialed is connected automatically. 00:01 1001234 (Figure 3.1.4- 2) ▶ Press the [SND/RDL] button, and then the speaker Phone operates automatically. 00:01 ▶ The last number dialed is connected. 1001234 (Figure 3.1.4- 3) 3.1.5 Speed Dial You can store up to 99 phone numbers in this phone using 2-digit addresses (01~99). The stored numbers in the Phone Book allow you to make a call simply by just press these addresses.
DTP-800/DTP-1900 Operating Manual ▶ Pick up the handset or press the [SPK] button. ▶ Press the memory station number stored in the address [1] ~ [9] for over 2 seconds then the stored number dialed, or press the memory station number shortly, and then press the [SND/RDL] button. Speed Dialing Memory 1 (Figure 3.1.5.1- 1) (Example) When you want to make a call to the number stored in address [1], press the [SND/RDL] button after press [1] button shortly or press [1] button for over 2 seconds.
DTP-800/DTP-1900 Operating Manual ▶ The speaker phone operates automatically and the phone number stored in the Phone Book is connected. Connecting… 1001234 (Figure 3.1.5.1- 4) 3.1.5.2 Two-Touch Dialing This function allows you to simply make a call using the phone numbers stored in addresses 10 through 99. ▶ Pick up the handset or press the [SPK] button.
DTP-800/DTP-1900 Operating Manual ▶ The number in the Phone Book is connected. Connecting… 1001234 (Figure 3.1.5.2- 2) ▶ Press the button of the phone number stored in any of Address [10] ~ [99], and then press the [SND/RDL] button. Speed Dialing Memory 12 (Figure 3.1.5.2- 3) ▶ The speaker phone operates automatically and the phone number stored in the Phone Book is connected. Connecting… 1001234 (Figure 3.1.5.
DTP-800/DTP-1900 Operating Manual 3.2 Answering Calls 3.2.1 On-Hook State ▶ When a call is being received, the phone rings. ▶ If you subscribe a caller ID service, the calling party information will be displayed in the third line on the screen. And the information will be displayed in the fourth line on the screen if the calling party number is stored in your Phone Book. Ringing… 1001234 03:DOWTEL (Figure 3.2.
DTP-800/DTP-1900 Operating Manual 3.2.2 Off-Hook State ▶ If a call is being received when the handset is picked up or the speaker is on, click the Hook Switch or press [SPK] button, and then the call is connected., Ringing… 1001234 (Figure 3.2.2- 1) 00:01 1001234 (Figure 3.2.
DTP-800/DTP-1900 Operating Manual 3.3 Disconnecting Calls 3.3.1 Using the Handset ▶ Hang up the handset when the call is finished. ▶ If the calling party hang up the phone before you do that, the warning-tone sound is supplied through the earpiece until you hang up the phone. Nov 11 (Sun) 11:11 am (Figure 3.3.1) 3.3.2 Using the Speaker Phone ▶ Press the [SPK] button when the call is finished.
DTP-800/DTP-1900 Operating Manual 3.4 Transfer between Handset & Speaker Phone 3.4.1 Transfer to Speaker Phone in Off-Hook State ▶ When you press the [SPK] button under the Off-Hook state, the [SPK] lamp is turned on and voice is out through the speaker. 00:01 1001234 (Figure 3.4.1) 3.4.2 Transfer to Handset in Speaker ON State ▶ If you pick up the handset when the [SPK] lamp is on, the [SPK] lamp is turned off and voice is out through the earpiece. 00:01 1001234 (Figure 3.4.
DTP-800/DTP-1900 Operating Manual 3.5 Volume Control You can adjust the volume from low to high in 5 different levels. 3.5.1 Keypad Tone Control ▶ The Keypad Tone can be changed by pressing [▲ ] or [▼ ] button when the handset is on the phone and the [SPK] button is off. Keypad Volume ☞ (Figure 3.5.1) 3.5.2 Ear Volume Control ▶ The Ear Volume can be changed by pressing [▲ ] or [▼ ] button after you pick up the handset.
DTP-800/DTP-1900 Operating Manual 3.5.4 Ringer Volume Control ▶ The Ringer Volume can be changed by pressing [▲ ] or [▼ ] button when the phone is ringing. Ringer Volume ☞ (Figure 3.5.
DTP-800/DTP-1900 Operating Manual 3.6 Hot Line This function is useful when you want to make an automatic call to the designated number without dialing or pressing the [SND/RDL] button. Hot Line operates in 2 modes. ▶ Timed Hot Line : This will make a call to the designated number without dialing or pressing the [SND/RDL] button within the Sending Time(4 ~ 8 seconds) after you pick up the handset.
DTP-800/DTP-1900 Operating Manual 3.7 Emergency Call Hold This function is used in the emergency situation and once the call is connected, it won’ t be disconnected as long as the receiver does not hang up. You can store up to three emergency call hold numbers at address 01 ~ 03 in the Phone Book. (Reference 4.4 Phone Book Function) You can set the ON/OFF of the Emergency Call Hold function using the Menu Mode. (Reference 5.4.
DTP-800/DTP-1900 Operating Manual 3.8 Do Not Disturb (DND) When you don’ t want to answer the incoming call, use this function. [Setting ON] ▶ Press the [DND/MUTE] button when the handset is on the phone and the [SPK] lamp is off. ▶ The phone doesn’ t answer to the incoming call and the DND icon is flashing simultaneously. Nov 11 (Sun) 11:11 am (Figure 3.8- 1) [Setting OFF] ▶ Press the [DND/MUTE] button when the handset is on the phone and the [SPK] lamp is off.
DTP-800/DTP-1900 Operating Manual 3.9 Voice Mute 3.9.1 Functions During the conversation, if you don’ t want to transmit your voice or sound to the called party, use this function. You can use this function the following case. - When you input the memo in the phone Book using the keypad. When you need to control the Menu to change the Voice Privacy function during the conversation. When you use the Memo Storing function during the conversation. 3.9.
DTP-800/DTP-1900 Operating Manual ▶ When the setting is done, the Voice Mute Icon is appeared on the screen and any voice or sound will not be transmitted to the other party. 00:36 ▶ If you want to release this function, select the in figure 3.9.2-2 and press the [STORE] button. (Figure 3.9.2- 3) This fun ction is valid in each call. Even though you finish the call with [Mute] status, the phone is returned to [Unmute] status automatically.
DTP-800/DTP-1900 Operating Manual 4. Additional Functions 4.1 Short Message Service (SMS) You can transmit/receive the simple text or voice message using this phone. MESSAGE ! 4/10 11:45am (Fi gur e 4. 1- 1) VOICE MAIL 4/10 11:45am (Figure 4.1- 2) ▶ When the phone received the text message, the sign like the figure 4.1-1 is appeared on the screen with the SMS/VMS notification tone. ▶ To retrieve the text message, ① Press the [CLR] button to return to the idle-state.
DTP-800/DTP-1900 Operating Manual ▶ To send the text message. ① Press the [MSG/VAS] button in the idle-state, and then press the [MENU] button. ② Press the [1] button to input the receiver’ s name, and then press the [STORE] button. ③ Press the [2] button again to input the message, and then press the [STORE] button. ④ Press the [3] button to input the calling party’ s name, and then press the [STORE] button. ⑤ Press the [4] button, and then the text message is transmitted to the called party.
DTP-800/DTP-1900 Operating Manual 4.2 Alarm Reminder This phone has Time Alarm function. You can set the alarm time under the 12-hour system. - The phone has a Two-type mode (Onetime Mode and an Always Mode). The Alarm time can be set and edit under the 12-hour system. - Onetime Mode; The alarm rings at the specified time, and then the setting mode is released automatically. But the stored time will be remained.
DTP-800/DTP-1900 Operating Manual 4.3 Voice Privacy (System Dependent) 4.3.1 On-hook State ▶ Press [MENU]à3à4 in order and Select mode or mode by using [▲ ] or [▼ ] button, and then press the [STORE] button. Voice Privacy Standard (그림 4.3.1) 4.3.2 During a Conversation ▶ Press [MENU] button during a conversation and press <1>. ▶ Select mode or mode by using [▲ ] or [▼ ] button, and then press the [STORE] button. 1. Voice Privacy 2. Memo Dialing (그림 4.3.
DTP-800/DTP-1900 Operating Manual 4.5 Using the Phone Book 4.5.1 Store the Phone Number in idle-state ▶ When the state of the phone is in idle-state, Nov 11 (Sun) 11:11 am (Figure 4.5.1- 1) ▶ Enter the phone number using the dial button, and then press the [STORE] button. 1001234 (Figure 4.5.1- 2) ▶ The figure 4.5.1-3 is displayed on the screen. ▶ Type the name using the dial button, and then press the [STORE] button.
DTP-800/DTP-1900 Operating Manual ▶ The figure 4.5.1-4 is displayed on the screen. ▶ Press the memory location number you want to store the phone number, and then press the [STORE] button. <
> ▶ If you just press the [STORE] button, the number is stored at memory location number [03]. User Define [??] Auto [03] (Figure 4.5.1- 4) 4.5.2 Storing the Caller/Receiver Number When you make a call or answer to the incoming call, the number of caller and receiver is displayed on the LCD screen.DTP-800/DTP-1900 Operating Manual [Note] The incoming call’s number is displayed in the left side on the screen and the making call’ s number is displayed in the right side on the screen to separate between the incoming call and making call. [Making Call] ▶ The number of called party is displayed on the screen when you dial the number. 00:01 1001234 (Figure 4.5.2- 3) ▶ When you finished a call, the number is shown for 3 seconds on the screen. ▶ At this time, press the [STORE] button. (Reference 4.5.
DTP-800/DTP-1900 Operating Manual 4.5.3 Storing the Memo during a conversation During a conversation, you can enter the number using the dial button and store the number in the Phone Book or make a call after the call is finished. ▶ Press the [MENU] button during a conversation. 1. Voice Privacy 2. Memo Dialing (Figure 4.5.3- 1) ▶ Press the [2] button, and then enter the phone number during a conversation using keypad.
DTP-800/DTP-1900 Operating Manual 4.5.4 Search the Stored Number ▶ When the phone is in idle-state, the screen(Figure 4.5.4 -1) is displayed if you press the [RCL] button. 1.Address Search 2.Name Search 3.Last 10 Dialed (Figure 4.5.4- 1) ▶ When you press the [1] button, the screen(Figure 4.5.4 -2) is displayed. ▶ Enter the memory location number using the dial button. <
> User Define [??] (Figure 4.5.4- 2) ▶ The name and number is displayed on the screen as shown in figure 4.5.4-3.DTP-800/DTP-1900 Operating Manual ▶ If you press the [UP]/[Down] button in the figure 4.5.4-3, you can search other number. ▶ Select the address you want, and then press the [STORE] button. The phone displays the number of the stored address. 01:DOWTEL 02:TOM 08:JERRY ▶ When you pick up the phone or press the [SND/RDL] button, the phone make a call the selected number. (Figure 4.5.4- 4) ▶ If you press the [2] button in the figure 4.5.4-1, the screen(figure 4.5.4-5) is displayed on the screen.
DTP-800/DTP-1900 Operating Manual ▶ If you press the [3] button in the figure 4.5.4-1, the screen(figure 4.5.4-7) is displayed. 01:0172890085 ▶ Select the number using the [UP]/[DOWN] button, and then press the [STORE] button. The phone displays the number of the stored number. 02:0166121601 03:9176203899 ▶ Press the [SND/RDL] button or pick up the phone, and then the phone will make a call. (Figure 4.5.4- 7) 4.5.
DTP-800/DTP-1900 Operating Manual ▶ Select the [1] button in the figure 4.5.5-1, and then you can change the number using the [CLR] and dial button. 1001234 (Figure 4.5.5- 3) ▶ After changing the number in the figure 4.5.5-3, press the [STORE] button. ▶ The screen is changed automatically as shown in the figure 4.5.5-3, and then you can change the name using the [CLR] and dial button. <> DOWTEL 1001234 (Figure 4.5.
DTP-800/DTP-1900 Operating Manual ▶ When the address that you enter in the figure 4.5.5-4 is already existed on the phone book, the phone will ask you to replace the address or not. < Overwrite? > 1. ▶ If you select the “ Yes” , the address will be replaced. 2. NO ▶ If you select the “ No”, the original number will remain at that address and you should store new address as shown on the figure 4.5.5-4. (Figure 4.5.
DTP-800/DTP-1900 Operating Manual ▶ Press the [Menu] button in the figure 4.5.6-1, the screen is changed in the edit state. 01:DOWTEL 1. EDIT 2. DELETE (Figure 4.5.6- 2) ▶ If you select the [2] button in the figure 4.5.6-2, the screen will be changed like the figure 4.5.6-3. ▶ If you select the “ Yes” , the address will be erased. ▶ If you select the “ No” , the address will not be erased and the screen will be changed to the figure 4.5.6-1. DELETE #01 [1]YES [2]NO 100123 4 (Figure 4.5.
DTP-800/DTP-1900 Operating Manual 4.6 List of the Dialed Number 4.6.1 Last 10 Called Number ▶ Press the [RCL] button when the phone is in the idle-state. ▶ The screen (figure 4.6.1-1) is displayed. 1.Address Search 2.Name Search 3.Last 10 Calls (Figure 4.6.1- 1) ▶ In the figure 4.6.1-1, you can see the dialed list up to 10 numbers when you press the [3] button. 01:0192548962 02:0166121601 03:9176203899 (Figure 4.6.1.
DTP-800/DTP-1900 Operating Manual 4.7 DATA Service 4.7.1 Definition DTP-800/1900 provides the Data Service. You can transmit and receive the data or fax data through the wireless path as connecting the Notebook (or Desktop PC) with DTP-800/1900. The following service is available. ① Async Data Service - File transmit and receive - PC communication ② PC Fax Service - Wireless Fax transmit/receive using the Winfax or Hotfax ③ Packet Data Service - FTP, Internet, Intranet, LAN, E-Mail etc. 4.7.
DTP-800/DTP-1900 Operating Manual 5. Menu 5.1 Menu Mode 1. Sound Control 1. Ring Select 2. DTMF Tone Len 3. Keypad Volume 4. Ringer Volume 5. Ear Volume 6. Speaker Volume 2. Management 1. Talk Time Info 1. Recent Call 2. Outgoing Lock 2. Total Calls 3. Lock Code 3. Clr Info Above 4. Phone Info 1. Phone Number 2. S/W Version 3. Call Functions 5. Clr Memory 1. Last 10 Calls 6. Reset As Default 2. Phone Book 1. Speed Dial 2. Emergency Call 3. Hotline Call 4. Voice Privacy 5. Alert per 1 min 6.
DTP-800/DTP-1900 Operating Manual 5.2 Sound Control You can select the tone types, ring types and sound volume of this phone using the Menu Mode. 5.2.1 Ring Select You can select the ring types when the phone rings. There are 6 Bell-Type and 4 Melody-Type in this phone. ▶ Press the button following sequence; [MENU] → 1 → 1 ▶ The screen(figure 5.2.1) is displayed with the current setting ring sound.
DTP-800/DTP-1900 Operating Manual ▶ Press the button as following sequence; [MENU] → 1 → 2 DTMF Tone Length ▶ The screen(figure 5.2.2) is displayed. Short → ▶ At this time, select the DTMF Mode you want using the [▼ ] or [ ▲ ] button and then press the [ STORE] button to store. (Figure 5.2.2) 5.2.3 Keypad Tone (Volume) This menu is used to select the keypad tone. This function has mode and 5-volume level.
DTP-800/DTP-1900 Operating Manual 5.2.4 Ringer Volume This menu is to select the ringer volume. This function has from mode to 5-volume level. ▶ Press the button as following sequence; [MENU] → 1 → 4 ▶ The current volume level is displayed on the screen(figure 5.2.4). Ringer Volume ☞ ▶ At this time, select the volume level you want using the [ ▼ ] or [ ▲ ] button and then press the [ STORE] button to store the ringer volume. (Figure 5.2.
DTP-800/DTP-1900 Operating Manual [Speed Menu] You can select the volume level simply using the [▼ ] or [▲ ] button when you pick up the handset. 5.2.6 Speaker Volume This menu is used to select the speaker volume. This function has 5-volume level. ▶ Press the button as following sequence; [MENU] → 1 → 6 ▶ The current volume level is displayed on the screen(figure 5.2.6). ▶ At this time, select the volume level you want using the [ ▼ ] or [ ▲ ] button and then press the [ STORE] button to store.
DTP-800/DTP-1900 Operating Manual 5.3 Management You can use this function to limit the phone use by others. And also, memory management, editing Lock Code, Reset as default and checking phone version are available. ▶ Press the button as following sequence [MENU] → 2 ▶ The phone ask you the user’ s password as in the figure 5.3 -1. 0000 The default password is “0000”. (Figure 5.3- 1) ▶ When you enter the user’ s password, the Management Menu is displayed on the screen 1.
DTP-800/DTP-1900 Operating Manual 5.3.1 Talk Time Information The phone records the call time when you make a call only. You can search or erase the records using this menu. ▶ Press the button as following sequence. [MENU] → 2 → Password → 1 1:Recent Call 2:Total Calls 3:Clr Info Above (Figure 5.3.1) [Note] The item’ s number 1 and 2 in this menu is initialized automatically when you turn the power of this phone off and then on again. 5.3.1.
DTP-800/DTP-1900 Operating Manual 5.3.1.2 Total Calls ▶ The total call time is displayed on the screen when you press the [2] button as the figure 5.3.1. Total Calls ▶ The total call time is displayed as [Hour:Minute:Second] & the number of Calls. 00:05:13 3 Calls (Figure 5.3.1- 2) 5.3.1.3 Clr(clear) Info(rmation) above The above items are initialized automatically when you turn the power off and on again. And you can initialize these items using the menu as follows. ▶ The screen (figure 5.3.
DTP-800/DTP-1900 Operating Manual 5.3.2 Outgoing (Call) Lock This menu is to limit or permit to make a call. ▶ Press the button as following sequence. [MENU] → 2 → Password → 2 Outgoing Call ▶ The / menu is toggled in the bottom of the screen. ▶ When the menu is displayed, press the [STORE] button. Lock ? → Yes (Figure 5.3.2) ▶ No outgoing calls can be made. 5.3.3 Lock Code (Password Change) This menu is used to change the user’ s password. ▶ Press the button as following sequence.
DTP-800/DTP-1900 Operating Manual ▶ If the reentered new password is not correct, the figure 5.3.3-3 is displayed on the screen and the phone is returned to the figure 5.3.31. No Match! Please Try Again (Figure 5.3.3- 3) 5.3.4 Phone Information This menu is to confirm the number of the phone and the software version. ▶ Press the button as following sequence. [MENU] → 2 → Password → 4 1:Phone Number ▶ The figure 5.3.4 is displayed on the screen. 2:S/W Version (Figure 5.3.4) 5.3.4.
DTP-800/DTP-1900 Operating Manual 5.3.4.2 S/W Version ▶ If you press the [2] button in the figure 5.3.4, the installed S/W Version in the phone is displayed on the screen. S/W Version ST0PP0-04.07 (Figure 5.3.4.2) 5.3.5 Clear Memory This menu is to erase the list of last-dialed number and the stored numbers in the Phone Book. ▶ Press the button as following sequence. [MENU] → 2 → Password → 5 1:Last 10 Calls ▶ The figure 5.3.5 is displayed on the screen. 2:Phone Book (Figure 5.3.5) 5.3.5.
DTP-800/DTP-1900 Operating Manual 5.3.5.2 (Clear) Phone Book ▶ If you press the [2] button in the figure 5.3.5, the figure 5.3.5-2 is displayed on the screen. ▶ If you want to erase the records of the Phone Book, press the [STORE] button when “ Yes” menu is appeared on the screen after press the [▲ ] or [ ▼ ] button. Phone Book Clear ? Yes (Figure 5.3.5- 2) 5.3.6 Reset as Default This menu is used when you want to recover the changed functions to the initial status.
DTP-800/DTP-1900 Operating Manual The Check Points when using the Reset As Default Function When you re-initialize the phone using this function, only the following items will be re-initialized to the default value. No. Item Default Value Remark 1 Keypad Volume 3 Steps 5.2.3 2 Ringer Volume 3 Steps 5.2.4 3 Ear Volume 3 Steps 5.2.5 4 Speaker Volume 3 Steps 5.2.6 5 Outgoing Lock No 5.3.2 6 Speed Dial Enabled 5.4.1 7 Emergency Call Disabled 5.4.2 8 Hotline Call Disabled 5.
DTP-800/DTP-1900 Operating Manual 5.4 Call Functions This menu is to set or release some useful function related with the calls. ▶ Press the button as following sequence. [MENU] → 3 1.Speed Dial ▶ The figure 5.4 is displayed on the screen. 2.Emergency Call 3.Hotline Call (Figure 5.4) 5.4.1 Speed Dial ▶ Press the button as following sequence. [MENU] → 3 → 1 Speed Dial ▶ The figure 5.4.1 is displayed on the screen.
DTP-800/DTP-1900 Operating Manual 5.4.2 Emergency Call ▶ Press the button as following sequence. [MENU] → 3 → 2 Emergency Call ▶ The figure 5.4.2 is displayed on the screen. Enabled ▶ If you press the [STORE] button when the menu is appeared after you press the [▲ ] or [▼ ] button, this function is set on. (Figure 5.4.2) ▶ If you press the [STORE] button when the menu is appeared, this function is released. 5.4.3 Hot-Line Call ▶ Press the button as following sequence.
DTP-800/DTP-1900 Operating Manual ▶ If you press the [STORE] button when the figure 5.4.3-3 is displayed on the screen, the phone is in “ Timed Hotline” state. ▶ And then the screen will be changed to the figure 5.4.3-4. Hotline Call Timed (Figure 5.4.3- 3) ▶ When you press the [STORE] button after you set the time using the [▲ ] or [▼ ] button, the setting is done. ▶ You can set the time between 4 ~ 8 seconds. Delay Time 6 seconds (Figure 5.4.3- 4) 5.4.
DTP-800/DTP-1900 Operating Manual ▶ If you press [▲ ] /[▼ ] button, the figure 5.4.4-2 is displayed on the screen. Voice Privacy ▶ And then, if you press the [STORE] button, the phone is in the enhanced privacy mode. Enhanced (Figure 5.4.4- 2) 5.4.5 Alert per 1 min This menu is used to set or release the alarm sound every 1-minute during the call. ▶ Press the button as following sequence. [MENU] → 3 → 5 Alert per 1 min ▶ The figure 5.4.5 is displayed on the screen.
DTP-800/DTP-1900 Operating Manual ▶ Select the “ Yes” or “ No” menu using the [▲ ] or [▼ ] button, and then press the [STORE] button. Automatic Dialing Enabled (Figure 5.4.6- 1) ▶ When you select the “ Yes” menu, the figure 5.4.6-2 is displayed on the screen. ▶ Select the time using the [▲ ] or [▼ ] button, and then press the [STORE] button. Delay Time 6 seconds (Figure 5.4.6- 2) 5.
DTP-800/DTP-1900 Operating Manual 5.5.1 Alarm Setting This menu is used to set on/off the alarm function and the alarm time. ▶ Press the button as following sequence. [MENU] → 4 → 1 Alarm Time ▶ The figure 5.5.1-1 is displayed on the screen. ▶ When you set the alarm time, the screen will prompt you to enter the time. 08:30 AM (Figure 5.5.1- 1) ▶ Use the dial button when you enter the time. ▶ Use the [UP/DOWN] button when you select the AM/PM. ▶ And then, press the [STORE] button.
DTP-800/DTP-1900 Operating Manual ▶ If you want to use the alarm for only one time, select the figure 5.5.1-3 using the [ ▲ ] or [ ▼ ] button in the figure 5.5.1 - 2 and then press the [ STORE] button. Alarm Mode Only Once (Figure 5.5.1- 3) ▶ If you want to use the alarm always, select the figure 5.5.1-4 using the [ ▲ ] or [▼ ] button in the figure 5.5.1- 2 and then press the [ STORE] button. Alarm Mode Always (Figure 5.5.1- 4) 5.5.
DTP-800/DTP-1900 Operating Manual ▶ When you select the figure 5.5.22 using the [▲ ] or [▼ ] button in the figure 5.5.2-1, press the [STORE] button. ▶ The phone stays at the Modem Receive Mode. Modem Receive Mode Always (Figure 5.5.2- 2) ▶ When you select the figure 5.5.23 using the [▲ ] or [▼ ] button in the figure 5.5.2-1, press the [STORE] button. ▶ The phone works the Modem Receive Mode only one time and returns to the voice-call mode. Modem Receive Mode One Time (Figure 5.5.
DTP-800/DTP-1900 Operating Manual ▶ When the phone is set in the PC Fax Receive Mode, the PC Fax Receive Mode Icon is displayed on the screen. ▶ When the phone is set in the Modem receive Mode, the Modem receiving mode Icon is also displayed on the screen. Apr 09 (Mon) 1:41pm 5.5.3 Font Select This model supplies 2 type text fonts. This menu is used to select the text font for LCD displ ay. Default text font is . ▶ Press the button as following sequence.