Installation & Assembly

A 20 ea
Sleeve
H 4 ea
Lower pole
J 1 ea
Wrench
K 4 ea
Threaded connector
(May be already
attached to G or H)
B 2 ea
Wheel
C 2 ea
Wheel with lock
D 1 ea
Bottom Shelf
E 1 ea
Pull-out shelf
F 1 ea
Utensil hooks
I 1 ea
Wood top
Assembly
Time:
Less than
30 minutes.
This product's intended
use is for added shelving
space in the kitchen.
Tools Needed: No tools required. Wrench included
STEP 3.
Slide
assembled
poles through
shelf corners
until bottom
shelf (D)
rests firmly on
sleeves. Push
or gently tap
the shelf down
at corners to
level shelf.
Part
A
B
C
D
E
Part
F
G
H
I
J
K
G 4 ea
Upper pole
STEP 2. Starting at the
bottom (the end with the
wheel), snap two sleeves
(A) onto poles (H) at
desired intervals. The
sleeves are marked with
a directional arrow to show
proper placement. Use
grooves on poles to ensure
even shelf placement
among the four poles.
NOTE: Place only enough
sleeves to assemble bottom
shelf. This step will be repeated
for each additional shelf.
STEP 5. Snap
two plastic sleeves
(A) onto two chrome
poles (left or right
side) at desired
intervals for the
utensil hooks (F).
NOTE: Place only
enough sleeves to
assemble (F).
STEP 6. Place wood top (I) onto top
of four poles, inserting rubber feet
on top into holes in top of poles. Press
top down until firm.
STEP 4. Snap
two plastic sleeves
(A) onto each
chrome pole (G/H)
at desired intervals
for the pull-out shelf.
Push or gently tap
the pull-out shelf (E) down
at corners to level shelf.
NOTE: Place only enough
sleeves to assemble pull-out shelf.
D
NOTE: To protect and extend
the life of the wood top,
periodically apply a food safe oil
on wood surface.
NOTE: part G is open at both ends with large
threaded hole at one end.
NOTE: part H has a small threaded hole on one end.
STEP 1. Connect upper pole (G) to lower pole (H) by
threading connector (K) into large threaded end of the
poles. Screw wheel (B) or (C) into assembled pole at small
threaded end. Repeat step 1 for remaining poles.
G
K
G
H
H
B C
G
A
H
E
A
A
F
I
Microwave Cart
NEED HELP? For help with assembly, or if you are missing a part,
please call or email us
Printed in China
THE COMPANY DISCLAIMS ALL OTHER WARRANTIES EXPRESS OR IMPLIED INCLUDING, WITHOUT LIMITATION, ANY IMPLIED
WARRANTIES OF MERCHANTABILITY OR FITNES S FOR A PARTICULAR PURPOSE, EXCEPT TO THE EXTENT THAT ANY WARRANTIES
IMPLIED BY LAW CANNOT BE VALIDLY WAIVED. NO ORAL OR WRITTEN INFORMATION OR ADVICE GIVEN BY THE COMPANY, ITS
DISTRIBUTORS, DEALERS, AGENTS OR EMPLOYEES, SHALL CREATE ANOTHER WARRANTY OR MODIFY THIS LIMITED WARRANTY. THIS
LIMITED WARRANTY STATES THE COMPANY'S ENTIRE LIABILITY AND YOUR EXCLUSIVE REMEDY AGAINST THE COMPANY FOR ANY
FAILURE OF OUR WIRE PRODUCT TO OPERATE PROPERLY. NEITHER THE COMPANY NOR ANYONE ELSE INVOLVED IN THE
DEVELOPMENT, PRODUCTION, OR DELIVERY OF OUR WIRE PRODUCT SHALL BE LIABLE FOR ANY INDIRECT, INCIDENTAL, SPECIAL,
CONSEQUENTIAL, EXEMPLARY, OR PUNITIVE DAMAGES, INCLUDING LOST PROFITS, ARISING FROM THE USE OF OR INABILITY TO USE
THE PRODUCT, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGES. SOME STATES DO NOT ALLOW THE EXCLUSION OR
LIMITATION OF INCIDENTAL OR CONSEQUENTIAL DAMAGES, SO THE ABOVE LIMITATION OR EXCLUSION MAY NOT APPLY TO YOU.
This Warranty gives you specific legal rights and you may also have other rights, which vary from State to State.
The Limited Warranty set forth above is provided on products purchased in and used in the United States, and is only in effect with
valid proof of purchase (bill of sale) presented or shipped (shipping cost prepaid) to the Company within the United States at the
address above.
TEN YEAR LIMITED WARRANTY
All our wire products distributed are warranted to the original purchaser at the time of purchase and for ten (10) years after the
purchase date ("warranty term"). We warrant to you, the original purchaser, that our wire products and all metal or plastic
parts and components are free of defects in material or workmanship during the warranty term. The word "defects" as used in
this limited warranty is defined as any imperfections which impair the use of wire product. This limited warranty is expressly
limited to the replacement or repair of metal or plastic parts and components (in the Company's discretion) and the Company will
have a reasonable amount of time to remedy said defect. This limited warranty only applies under conditions of normal use. This
limited warranty does not cover defects caused by improper assembly or disassembly, defects occurring after purchase due to
intentional damage, product modifications, exposure to the elements, accidents, misuse, abuse or negligence and labor or
assembly costs.