Wall Cabinet Date of Purchase ___ / ___ / ___ Lot Number: THIS INSTRUCTION BOOKLET CONTAINS IMPORTANT SAFETY INFORMATION. PLEASE READ AND KEEP FOR FUTURE REFERENCE. Do Not Return This Product! Contact our customer service team for help first. Easy WARNING ‐ Unit can tip over causing severe injury or death. ‐ Anchor unit to stud in wall (if instructed to). ‐ Do Not allow children to climb on unit. ‐ Put heavy items on lower shelves or drawers.
Contact Us! Do NOT return this product! Contact our friendly customer service team first for help. Assembly Tips Visit our website to view the limited warranty valid in the U.S. and Canada. You Tube Helpful Hints PEOPLE NEEDED FOR ASSEMBLY: 1‐2 ESTIMATED ASSEMBLY TIME: 1 HOUR ‐ Open your item in the area you plan to keep it to avoid excessive heavy lifting. ‐ Identify, sort and count the parts before attempting assembly. ‐ Compression dowels are lightly tapped in with a hammer.
k Quic bly em Ass Ti p Before You Start Read through each step carefully and follow the proper order Separate and count all your parts and hardware Give yourself enough room for the assembly process Have the following tools: Flat Head Screwdriver, #2 Phillips Head Screwdriver and Hammer Caution: If using a power drill or power screwdriver for screwing, please be aware to slow down and stop when screw is tight. Failure to do so may result in stripping the screw.
Board Identification Not actual size A B x2 Side Panel C Bottom Top G E D Adjustable Shelf F Left Door Wall Support Back Rail This piece is paperboard construction. It is not made from wood, but is required for the assembly of your unit.
Board Identification Not actual size E B A F J This piece is paperboard construction. It is not made from wood, but is required for the assembly of your unit.
Part List Actual Size (x12) #A22570 (x12) #A22510 (x2) #A11145 (x2) #A11195 cam lock cam bolt 1/ 2" flat head screw 5/ 8" pan head screw (x6) #A13800 2-1/ 4" flat head (x2) #A11210 (x2) #A89020 (x4) #A23700 (x4) #A80250 (x5) #A21500 3/ 4" pan head screw door stop rubber cap shelf support steel dowel Not Actual Size (x4) #A65615 (x1) #A55410 (x1) #A55015 (x2) #A52995 hinge latch lock handle 6
STEP 1 Quick Assembly Tip (x8) #A22570 (x4) #A22510 (x4) #A65615 Proper orientation of CAM LOCK Insert four cam locks and screw two cam bolts into both side panels (A) as shown. Loosen screw in hinge and separate hinge plate from hinge. Mount two hinge plates to both side panels (A) as shown. Loosen screw to separate hinge and hinge plate.
STEP 2 (x8) #A22510 (x2) #A89020 (x2) #A11195 Attach four cam bolts to the top (B) and bottom (C) as shown. Attach two door stops to the top (B) with screws as shown.
STEP 3 Quick Assembly Tip (x4) #A22570 (x5) #A21500 Proper orientation of CAM LOCK Insert two cam locks into both the back rail (E) and bottom rail (I) as shown. Insert the steel dowels into each part as shown.
STEP 4 UNLOCK LOCK Press the side panels (A) onto the back rail (E) and bottom rail (I) as shown and turn the cam locks clockwise to lock in place.
STEP 5 UNLOCK LOCK With the front finished edges facing up, attach the top (B) and bottom (C) as shown. Turn the cam locks clockwise to lock in place.
STEP 6 (x2) #A13800 Locate the wall studs and determine the placement for the cabinet. Mark the stud locations on the wall for the wall support (F). Drill two 3/16" (5mm) diameter holes in the center of the wall support (F) as shown. Locate the wall studs and attach the wall support to the wall into the studs using two screws, making sure the wall support is level. Hang cabinet onto wall support as shown. The distance from the bottom edge of the wall support (F) to the top surface of the top (B).
STEP 7 (x4) #A13800 After the cabinet is mounted to the wall, drill two 3/16" (5mm) diameter holes into the back rail (E) and bottom rail (I). Using screws, fasten the cabinet to the wall by screwing through the back and bottom rails (E&I). Use the same screw location that you used attaching the wall support (F) so the screws fasten to a stud. E F Drill and fasten screws here.
STEP 8 Unfold the back panel. Position the back panel into the cabinet opening with the fold lines of the back panel running up and down. Insert the bottom edge into the groove in the bottom (C). Fold the upper end of the back panel until it inserts into the groove in the top (B).
STEP 9 (x4) #A65615 (x1) #A55015 (x2) #A11145 (x1) #A55410 (x2) #A11210 Attach two hinges to each door (G&H) as shown. Attach the latch to the left door (G) with the longer screws and the lock to the right door with the shorter screws as shown. After the lock is attached, press the lock ring over the barrel of the lock and press until seated.
STEP 10 (x2) #A52995 (x4) #A23700 Attach a handle to each door as shown. Press a rubber cap onto each handle bolt as shown.
STEP 11 Loosen screw A Adjust door. Tighten screw A Loosen screw C Turn screw B to move door. Tighten screw C Loosen screw C Adjust door. Tighten screw C *side view To mount the doors, have the hinges in the open position. Slide the hinges onto the hinge plates and tighten screw "C".
STEP 12 (x4) #A80250 Insert the shelf supports at the desired level and place the adjustable shelf (D) onto the shelf supports.
STEP 13 To lock doors: Close the left door (G) first and press the latch down so the stop pin inserts into the hole in the bottom (C). Close the right door (H). Using the key, turn the lock so the locking bar extends behind the left door.
Maximum Loads This unit has been designed to support the maximum loads shown. Exceeding these load limits could cause sagging, instability, product collapse, and/or serious injury. 0 lbs 0 kg 25 lbs 11.3 kg 25 lbs 11.3 kg Warning: Risk of injury to persons ‐ do not place a television on this furniture. This furniture is not approved for use with a television. Certificate of Conformity 1. This certificate applies to the product identified by this instruction manual. 2.
Register your product to receive the following: * New trend details ‐ sneak peek on what's new * Surveys ‐ have a voice within our community * Exclusive deals and discount codes * Quick and easy replacement part service Visit your local retailer's website, rate your purchased product and leave us some feedback! We would like to extend a big "Thank You" to all of our customers for taking the time to assemble this product, and to give us your valuable feedback.
Español Cubierta Delantera Este libro de instrucciones contiene información IMPORTANTE de seguridad. Por favor lea y manténgalo para referencia en el futuro. No Regrese este producto! Comuniquese con nuestro amistoso equipo de servicio al cliente para obtener ayuda. PRECAUCION Este mueble puede volcarse y causar graves heridas y/o muerte. Anclar el mueble a un poste de madera en la pared (si esto se requiere). No Permita que los niños monten el mueble.
Español Página 7 Inserte cuatro levas de fijación y atornille dos pernos en ambos paneles laterales (A) como se muestra. Afloje el tornillo en la bisagra y separe la placa de la bisagra. Monte las dos placas de la bisagra en ambos paneles laterales (A) como se muestra. Afloje los tornillos para separar la bisagra y la placa de la bisagra. Página 8 Coloque cuatro pernos en la parte superior (B) y en la inferior (C) tal como se muestra.
Español Página 14 Despliegue el panel trasero. Coloque el panel posterior en la abertura del gabinete con las líneas de doblez de la parte trasera corriendo arriba y abajo del armario. Inserte el borde inferior en la ranura en la parte inferior (C). Doble el extremo superior de la parte trasera hasta que inserte en la ranura en la parte superior (B). Página 15 Coloque dos bisagras para cada puerta (G y H) como se muestra.
Español Página 21 Registre su producto para recibir lo siguiente: * Detalles de nuevas tendencias ‐ Vistazo a lo nuevo * Encuestas ‐ alec su voz entre su comunidad * Códigos de ofertas y descuentos exclusivos * Fácil y rápido servicio de partes de remplace Clasificasión de 5 estrellas Visite el sitio web de su tienda local, califique su comprado y denos sus comentarios! Nos gustaría enviar un gran "Agradecimiento" a todos nuestros clientes por tomarse el tiempo de ensamblar este producto, y por darnos sus v
Français Avant de Commencer (page 3) ‐Lisez attentivement chaque étape et suivez le bon ordre ‐Séparez et comptez toutes vos pièces et matériaux ‐Donnez‐vous suffisamment de place pour l'assemblage ‐Avoir les outils suivants: tournevis à tête plate, #2 tournevis Phillips, et Marteau ‐Attention: Si vous utilisez une perceuse électrique ou un tournevis électrique pour visser, veillez à ralentir et arrêter lorsque la vis est bien serrée. Le non‐respect de cette consigne peut endommager la vis.
Français Page 13 Après avoir monté l'armoire sur le mur, percez deux trous de 5 mm (3/16 pouces) de diamètre dans la glissière arrière (E) et la glissière inférieure (I). En utilisant des vis, fixez l'armoire au mur en vissant à travers les glissières arrière et inférieure (E&I). Utilisez le même emplacement de vis que vous avez utilisé pour fixer le support mural (F) afin que les vis tiennent à un poteau. Percez et serrez les vis ici. Page 14 Ouvrez le panneau arrière.
Français Page 20 CHARGES MAXIMALES Ce meuble a été conçu pour supporter les charges maximales indiquées. En excédant ces limites de charge, le meuble pourrait devenir instable, s'effondrer, et/ou causer des blessures graves. AVERTISSEMENT : Risque de blessure corporelle ‐ ne pas placer une télévision sur ce meuble. Ce meuble n'est pas approuvé pour une utilisation avec une télévision.
