User Manual

Wireless Portable Bluetooth Speaker
Mode No.: DOSS SoundBox
User Manual
Status indicators
Package content
Product overview
6. Long pr to turn the device on and off.
7. Auxiliary Φ3.5mm jack
devices.
8. TF card: Use it for TF card (with music) playback. support mp3,wav
that to FAT32 or FAT.
9. Charging port: Plug the supplied USB cable into this port to recharge
10. LED charging indicator.
• Charging : Steady Red.
• Fully charged : Steady Green.
Thank you for purchasing the DOSS SoundBox Wireless Portable Bluetooth
Speaker
wireless portable speaker.
• One wireless portable speaker
• USB charging cable
• Φ3.5mm auxiliary cable
• User manual
1. Mode switch: Touch to toggle play mode among Bluetooth,
2. In Bluetooth mode/TF mode, touch to skip backward.
3.
• In Bluetooth mode,touch to answer or end a call. Touch for 3
seconds to reject a call.
• In Bluetooth mode, touch to play/pause your tune. Touch for 3
seconds to disconnect with your device.
• In TF mode, touch to play/pause your tune.
4. In Bluetooth mode/TF mode, touch to skip forward.
5. Volume control:
Center indicator/
indicator
Flashing blue
Steady blue
Steady red
Steady green
Indicates that the speaker
has entered into the pairing
mode and it is ready to be
paired
Indicates that the device is
successfully paired
Steady red
Steady Green
Indicates that the device has
switched to the auxiliary
input mode
Indicates that the device has
switched to the TF mode
1
2
6 7 8 9 10
3
5
4
Product type: Wireless Portable Bluetooth Speaker with Built-in
Microphone
Output power: 6W x 2
Driver unit: 1.5 inch speaker x 2 + 2.6 inch passive radiator
Frequency response: 100Hz-18kHz
Unit weight: 560 g
Unit dimension: 6.6 x 2.7 x 2.9 inch
Warranty: One-year limited
Power
Warning
Wireless/Networking
• Input:5V 1A
Bluetooth versions
• Profiles supported
• Do NOT drop, hit or shake the device.
• Do NOT disassemble, repair or modify the Bluetooth speaker by yourself.
• Do NOT use cleaning products that contain benzene, solvents or alcohol.
• Do NOT expose the Bluetooth speaker to excessive heat or to direct
• Do NOT store the device in a place with high humidity or dust.
• Do NOT place heavy objects on top of the Bluetooth speaker.
• Do NOT use near a microwave oven or wireless LAN products.
Bluetooth
Problem
TF Card
other
Cannot Pair with Bluetooth
devices
seconds,then have a try to pair it
again
Please select 'DOSS SoundBox' as
the default playback device
The song cuts off during
playback
Please check if the Bluetooth
distance is more than 33 feet or
There is noise during playback Maybe caused by the
interference of charging,try to
put it in another place and do not
charge it during playback
Laptop prompts to install driver This driver is not special for
SoundBox,it's for your laptop
contact the computer company
or windows
The speaker do not play when
the card is inserted,and jump
directly back to Bluetooth
mode
Check whether the card format is FAT
or FAT32. If not, format it to FAT or
FAT32.
Check the song format. The speaker
only supports MP3, WAV
The song cuts off during
playback
All the lights are lit and can not
be turned off
Customer Service Email [e-mail]
Use the needle or wire to poke the
There may be a problem with the
the same file
for 5 seconds or contact with the
for help
3. Speak with a clear voice right into the built-in microphone located on
may also end the call directly using the command on your cell phone.
5. When listening to music using your smart phone, playback will resume
call using the speaker.
Using it with your Echo Dot
Note:
Download the Alexa APP, follow the standard setup procedure to
get the dot connected to your home Wi-Fi network.
1.
Switch the SoundBox speaker to Bluetooth mode,you can press the
2.
3.
Tap the Echo Dot in your list of Alexa Devices, then tap Bluetooth.4.
The SoundBox speaker should appear in the list of Bluetooth Devices.
listed, tap on The SoundBox speaker to complete the pairing process.
To remove the device, return to Bluetooth -> tap the name of the
speaker -> then tap "Forget Device".
5.
Voice command will not be able to turn on/off the Soundbox no
only translate sound signal.
upgrading the firmware.
1.
2.
Pairing the wireless speaker with your smart device
Answering and ending a call using your speaker or mobile
phone
• Use the supplied USB cable to charge your portable speaker directly
from your computer micro USB port or the cellphone adapter(please
confirm its output is 5V)
• Make sure that the speaker is fully charged before using it for the
Note:
1. When there is an incoming call, the speaker will generate a tone and
steps to turn the device off as well.
LED light will remain RED when charging and turn GREEN once charge
completes.
assistance, please contact: [e-mail]
1. Place your smart device and wireless speaker no more than one meter
away from each other.
seconds to turn it on.
3. Set your smart device to “discover” the wireless speaker. Upon
powering on, a tone will be heard, the blue LED will start flashing,
the pairing mode.
4. Enabled Bluetooth on your device and choose DOSS SoundBox from
the list.
5. If pairing is successful, the LED will change to steady blue and your
for 5 seconds and have a try again.
Note: If your smart device cannot discover the SoundBox,long press the
and have a try again.
You can connect the Dot with the speaker using a 3.5 mm auxin cable
or Bluetooth. Please use the following steps to set up using Bluetooth:
Wonders Technology Co.,Ltd
Email: [e-mail]
Follow us on Facebook:
Website: www.dossaudio.com
Tel.:[phone] Mon-Fri 9AM-5PM (PST)
≥
If the speaker beeps every few seconds, please recharge it for
2-3 hours.