带格式的: 边框:底端: (无框线) Device Operation Manual Version: [1.
带格式的: 边框:底端: (无框线) I. Installation of USB driver under windows XP 1. Unzip android_usb_driver.zip and adb_1.0.26.zip and guarantee there is no Chinese character in the route. 2. Check the “USB debugging” option in the device (route: Settings－>Application settings －>Development, as shown in the figures), open the program Otg mode change to switch to USB device and connect the device to PC through USB cable. 3.
带格式的: 边框:底端: (无框线) 5. System will search and install the driver automatically; “Completing the Found New Hardware Wizard” will be displayed after the installation. 6. Open the device manager (route: right click “my computer”, select “properties” and click “hardware” tab), newly added Android Composite ADB Interface device (under Android Phone Category), USB Composite Device and USB Mass Storage Device (under “universal serial bus controllers”) will be displayed.
带格式的: 边框:底端: (无框线) Note: 1. If yellow question mark is displayed on icons of the above three devices, please right click that device, select “update driver” and perform the above operations again. 2. If other Android device drivers have been installed in the computer, the computer may perform installation automatically rather than popup the hardware wizard dialog box. Under this circumstances, please check whether the device name identified in device manager is identical to the above device name.
带格式的: 边框:底端: (无框线) Click “Have Disk”, select the file “andriod_winusb.inf” under usb_driver folder in “Browse” dialog box and then click OK. II. ADB configuration under windows XP adb command can be run by entering the route of adb_1.0.26 folder through command line, or write the route into environment variables, so that adb can be run in any route.
带格式的: 边框:底端: (无框线) 1. Right click “my computer”, select “system properties”, click “advanced” tab, click “environment variables” button to open the dialog box of environment variables. 2. Select the variable “PATH” in “System variables” and click the “Edit” button below. 3. Add the route of adb_1.0.26 folder in the route for “Variable value”. Note: the route added shall be separated from the existing route with semicolon under English half-angle.
带格式的: 边框:底端: (无框线) 4. Open the command line (click start – run, input cmd and click OK button), click adb version to check whether the version of adb is 1.0.26. If not, please check whether the relatively previous version adb route is included in the environment variables, delete the route if it exists. Input adb devices, if device is identified and displayed, it means adb is well configured. 5. After the adb is well configured, the device can be operated through commands.
Operation Introduction to Demo Application Version: [1.
Contents I． Import of projects into eclipse.................................................................................................................. 1 II． Introduction to Demo.............................................................................................................................. 2 2.1． Operation introduction to MotionDemo ...................................................................................... 2 2.2． Operation introduction to ReadCard ............................
I． Import of projects into eclipse 1. Open eclipse, click the files menu, select “import”, in the displayed dialog box, select “Existing Projects into Workspace” under “General” and click “next”. 2. Select “Select root directory”, click “Browse” to introduce the route of application program and then click “Finish” to complete the import of projects.
II． Introduction to Demo 2.1． Operation introduction to MotionDemo Sense level Time threshold value judges sense motion Motion sensed: Left to right Motion sensed: right to left Motion sensed: Left Motion sensed: right 1. Open the app list (click the app list button), find Motion Demo application, click the icon to enter into application program interface. 2. If it remains initial settings, card swiping motion can be tested when opening the surface.
1. Click the icon of ReadCard application program to enter into the application program interface. 2. Click “setup” button and the following interface will be popped out: 3. Click device and select "ttys2 (serial) ".
2. Anti-dumping alarm status is displayed at the first item in the application program interface. When the anti-dumping alarm switch in rear of the machine is pressed, this item will display “(on)”, which means alarm is triggered. 3. The second item in the application program interface is used to operate LED RED. When this button is pressed, the button turns red and LED RED is on; when this button is pressed again, LED RED will be off automatically. 4.
2. When swiping card in card wiping area, card number will be displayed and when the whole screen is occupied, screen will be cleared automatically. 2.5． Operation introduction to NewHIDDemo 1. Click the icon of NewHIDDemo application program to enter into the application program interface. 2. When swiping card in card wiping area, card number will be displayed. 2.6． Operation introduction to NewWiegenDemo 1.
cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: -- Reorient or relocate the receiving antenna. -- Increase the separation between the equipment and receiver. -- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. -- Consult the dealer or an experienced radio/TV technician for help.
