Installation Instructions

ManualsBrandsdormakaba Canada ManualsElectronicsElectro-mechanical Rack Handle Lock

INSTALLATION

3525PRX / DFR / iCL

ELECTROMECHANICAL RACK HANDLE LOCK

WITH READER

www.dormakaba.us • Phone: 1.800.265.6630 • Fax: 1.800.482.9795 • E-mail: sales_RCI@dormakaba.comIS3525PRX

PCN2105

R02-22GR

INSTALLATION

Specifications

Package Contents

• 3525 Electromechanical Rack Handle Lock with Reader

• M3x25 Mounting Screws (qty 4)

• M3x14 Mounting Screw

• Rotation Limiter Standard

• Rotation Limiter - Extended (for thicker panels)

• Cam Bolt

• Top Mounting Bracket

• Bottom Mounting Bracket

• Installation Instructions

• Keys (qty 3)

Actuator Module

Supply

Voltage

12VDC to 24VDC (NOTE: Status LED will blink red if

the supply voltage is out of range.)

Standby

Current

50mA maximum at 12VDC"

Operating

Current

see chart below

Stall Current 1A maximum at 12VDC (limited to 2 seconds)

Operating

Transit Time

1 second maximum (NOTE: Power must be present

during transit times. If power is removed while the lock

slide is in transit, it will complete it’s cycle when power

is restored.)

Electronic

Unlock Time

3 seconds minimum

Open

Collector

Outputs

Rated for supply voltage, maximum load

Alarm

Outputs

100mA/ output maximum

Fig. 1

Data Rack

Handle

Reader

Tri-Color Status

LED

Key Cylinder

Reader PRX DFR iCL

Voltage 12VDC ~ 24VDC

Operating

Current

20 mA

No External Load

125 mA

No External Load

60mA

No External Load

Transmit

Frequency

125 kHz FSK 13.56 MHz / 125 kHz 13.56 MHz

DATA Signal

Voltage

5VDC

DATA Pulse

Interval Time

40µs

DATA Signal

Delay

2ms

Output Format N/A

Reverse Byte Order (13.5MHz cards) Most Significant Bit First (125kHz

cards) Upper and Lower Parity Bit Included

Reverse Byte Order with

Upper and Lower Parity Bits

Overall

Dimensions

8-1/4” H x 1-1/2” W x 1” D

210mm x 37mm x 25mm (Depth from Cabinet Face)

Summary of content (4 pages)

PAGE 1
INSTALLATION 3525PRX / DFR / iCL ELECTROMECHANICAL RACK HANDLE LOCK WITH READER Reader Fig. 1 Actuator Module Supply 12VDC to 24VDC (NOTE: Status LED will blink red if Voltage the supply voltage is out of range.) Standby 50mA maximum at 12VDC" Current Operating see chart below Current Stall Current 1A maximum at 12VDC (limited to 2 seconds) 1 second maximum (NOTE: Power must be present Operating during transit times.
PAGE 2
BROWN - 200 mA OUTPUT FOR ALARM Fig. 2 1” * 25mm select appropriate Rotation Limiter Handle Mounting CAM 1. Assemble handle according to the proper handing required. 2. Rotation Limiter & Bottom Mounting bracket determines handing. (Fig. 3) Top Mounting Bracket 3. If existing cam or rod mechanism are installed on original handle remove and install on new handle. (minimum torque 4Nm) 5.9” * 150mm 4. Ensure the proper cutout in the door. (See Fig. 2) CAM Bolt M3x14mm Screw (1 place) 5.
PAGE 3
Wiring The 3525PRX/DFR/iCL contain two separate functional modules: Positive Red GND Black DATA1 White DATA0 Green The reader modules read the contents of a compatible proximity card and converts it to Wiegand format. The actuator module controls and monitors the locking function of the swinghandle. These two modules operate independently of each other and require connection to an access control unit (not provided), to be fully functional.
PAGE 4
+ Wiring (Continued) RED: Postive RED - 12/24 VDC POSITIVE BLACK - 12/24 VDC NEGATIVE BLACK: Negative WHITE - ACTIVATION TRIGGER YELLOW - 200 mA OUTPUT FOR ALARM BROWN - 200 mA OUTPUT FOR ALARM ORANGE: Activation Trigger BLUE: 100mA Output for Alarm BROWN: 100mA Output for Alarm Lock Status Latch LED Alarm Wires Secure Steady Blue Inactive Electrically Released Blue/ Magenta Flashing Brown Active Mechanically Released Blue Flashing Blue Active ORANGE Handle Not Fully Closed Blue/Red Fla