Page 2-16 Installation Manual IP Video Door Station D21x Series Seite 17-32 Installationsanleitung IP Video Türstation D21x Serie Page 33-48 Manuel d´installation Interphone vidéo IP Série D21x Página 49-64 Manual de Instalación Videoportero IP Serie D21x Pagina 65-80 Istruzioni per l’installazione Videocitofono IP Serie D21x IPVideo Door St at ion D21xRev.1.7 VERSION 3.0 MIN. HW 1.
INSTALLATION MANUAL Read these instructions carefully before starting to use any components. Keep the manual so you can refer to it at a later date if required. If you hand over the device to other persons for use, please hand over the operating manual as well. You can always find the most up-to-date version of the installation manual on www.doorbird.com/ support To make things easier we use the term “device” for the product “IP Video Door Station” and “mobile device” for a smartphone or tablet.
not associated with the installation, wiring, or connection. Electric shock could result. • On devices which are not marked as weatherproof: Keep the device away from water or any other liquid. • Do not install or make any wire terminations while power supply is plugged in. It can cause eletric shock or damage to the device. • Before turning on power, make sure wires are not crossed or shorted. If not, fire or eletric shock could result. • High voltage may be present internally. Do not open the device.
cause damage to the device. • Do not use chemicals, caustic agents, or aerosol cleaners. • Use a clean dry cloth for cleaning. • Use only accessories that comply with technical specification of the device. These can be provided by Bird Home Automation GmbH.
ENGLISH DEVICE EXAMPLE WITH 1 CALL BUTTON Front 1) HDTV Video 1 6 2) Light Sensor For night vision mode 2 7 3) Security screws 3 8 4) Motion Sensor 7) Microphone 5) Illuminated call button with nameplate The illumination is also acting as Diagnostic LED(s).
DEVICE EXAMPLE WITH DISPLAY MODULE AND KEYPAD MODULE Front 1) Night Vision LEDs 9) Display Module 1 2) HDTV Video 2 3) Microphone 10) Keypad Module The illumination is also acting as Diagnostic LED(s) 9 3 4) Light Sensor For night-vision mode 4 5 5) Security screws 6 7 10 6) Loudspeaker 7) RFID Reader 8 8) Motion Sensor Inside 1 1) Main Electrical Unit 2 2) Yellow cable for call button (unused) 3 4 5 6 7 3) Red cable for Module Port 1 Connected to the Display Module 4) Green cable for
ENGLISH DEVICE EXAMPLE WITH FINGERPRINT READER MODULE Front 1) HDTV Video 1 6 2) Light Sensor For night vision mode 2 7 3) Security screws 3 8 4) Motion Sensor 5) Illuminated call button with nameplate The illumination is also acting as Diagnostic LED(s).
1 2 SWITCHING OFF POWER Switch off the power to all wires leading to the assembly location, i.e. the door chime, electric door opener, power supply unit for the video door station etc. 3 DISMANTLING THE EXISTING DOORBELL Should there already be a doorbell or door station on the exterior wall of the house, please dismantle it. DETERMINING THE ASSEMBLY LOCATION The device uses an ultra wide-angle hemispheric lens so that even when the person is a minimum distance of 50 cm (19.
ENGLISH 5 ASSEMBLING THE MOUNTING HOUSING Remove the front panel carefully using the screw driver provided with the device from the mounting housing (backbox). You can find detailed drawings and measurements of the device in the corresponding datasheet. If you must drill holes in a wall, insert screws into a wall or lever up a wall, ensure that no cables or mains (gas, water, etc.) are to be found in the wall.
OPTION 2 Power supply using the power supply unit (mains adaptor) Power supplies can be purchased from us, but we generally recommend using only Power over Ethernet (PoE) as the power supply. Do not plug the power supply unit into the wall socket yet. Only use the original DoorBird power supply unit or a DIN-rail power supply unit that you can obtain from us separately, since this has been specially stabilized electrically and is equipped with an integrated audio interference reduction device.
DESCRIPTION LAN/POE RJ45 jack to connect the Network coming from the Internet Router/PoE-Switch/PoEInjector. NOT IC E REL1, REL1 REL1 REL1 ENGLISH PORT Do not power the device simultaneously via the power supply from the power supply unit (mains adaptor) and the power supply via PoE. Bi-stable latching relay #1, max. 24 V DC / AC, 1 Ampere. Security feature: The relay keeps its state even in the case of loss of power.
N OTI C E 8 The yellow, green, and red cables that lead out from the side of the Main Electrical Unit must only be used to connect components certified by Bird Home Automation. ASSEMBLING THE FRONT PANEL Assemble the front panel of the device to the mounting housing (backbox) of the device. 1.) Pull the front panel into the mounting housing (backbox) 9 2.) Push the front panel up. 3.) Insert the security screws. ACTIVATING THE DEVICE Switch on the power leading to the assembly location again.
Engraving Service You can see if the device is powered by checking the Diagnostic-LED, which lights up after about 30 to 60 seconds after the power is connected. Engraving service for a modern and clean appearance: www.doorbird.com/engraving Please follow STEP 1 to switch off power. We recommend to use a thin slot screwdriver to remove the cover of the nameplate. We recommend to use white paper for the label which does not absorb moisture.
MAINTENANCE FOR DOORBIRD PRODUCTS Cleaning and maintenance instructions All DoorBird door stations are made of high-quality materials and are designed for a durable lifetime. Since door stations are usually installed in unprotected outdoor areas, they are exposed to adverse weather conditions and aggressive substances, especially close to frequently used roads, in coastal and industrial areas. Therefore please consider the following care instructions.
IP65, CE, FCC, IC, RoHS, IK08, REACH, IEC/EN 62368, IEC/EN 62471 Operating conditions -25 to +55°C / -13 to 131°F Humidity 10 to 85 % RH (non-condensing) Scope of delivery 1x Main Electrical Unit 1x Front panel* (110 - 240 V AC to 15 V DC) 1x RFID key fob 1x Screwdriver 1x Quickstart guide with Passaporto digitale 1x Installation manual 1x Small parts Warranty MOTION SENSOR Type Active Detection angle 54° (H), 70° (V) 1 - 10 m (3.3 - 32.9 ft), depends on environment, configurable in 1 m (3.
LEGAL NOTES General remarks 1. DoorBird is a registered trademark of Bird Home Automation GmbH. 2. Apple, the Apple logo, Mac, Mac OS, Macintosh, iPad, Multi-Touch, iOS, iPhone and iPod touch are trademarks of Apple Inc. Automation GmbH‘s servers. This process is gradual and can take several weeks. As soon as a product receives a firmware update, the system will be installed and will restart by itself. Installed firmware updates cannot be undone.
IC Caution: This device contains licence-exempt transmitter(s)/receiver(s) that comply with Innovation, Science and Economic Development Canada’ s licence-exempt RSS(s). Operation is subject to the following two conditions: (1) This device may not cause interference. (2) This device must accept any interference, including interference that may cause undesired operation of the device.
www.doorbird.