V20221115 SLIDING GATE OPENER USER MANUAL Read Carefully Before Use Keep for Future Reference
Safety Information Warning! • Read these instructions completely before installation and use. Provide them to any technician used to install, maintain, or repair this device and provide them with the device if it is ever given or sold to a third party. • Install and use this gate opener only in accordance with these instructions and all applicable local and national laws and regulations. Adding instructional or warning signage may be necessary in your area.
Specifications Model 2700 3300 Input Power 110–120 V~ 60 Hz 110–120 V~ 60 Hz Rated Power Torque 0.54 hp 400W 0.74 hp 550W 16.2 lb.-ft. 22 N·m 23.6 lb.-ft. 32 N·m Duty Cycle S2 20 min. S2 20 min. Max. Gate Weight 2700 lb. 1.35 T 1200 kg 1.2 MT 3300 lb. 1.65 T 1500 kg 1.5 MT Max. Gate Speed 42.5 fpm 13 m/min. 42.5 fpm 13 m/min. 20 ft. 6m 20 ft. 6m Max. Gate Length Max. Noise 60 dB 60 dB Min. Temperature −4°F −20°C −4°F −20°C Max.
Package List No.
No.
Installation Initial Setup 1. Ensure that your gate does not exceed your model's weight capacity and includes the following features or their equivalent. Track and Wheels End Catch Guide Rollers End Stop Figure 1 2. Ensure that your gate does not exceed 40 feet (12 m) in length. If it exceeds 20 feet (6 m) in length, you will need to purchase additional ANSI #41 chain and connect it to those provided with your device.
4. Ensure that the gate opener will have a suitable location on firm level ground at least one foot (30 cm) inside the chain bracket on the nearest end of the gate. The default settings for this motor are for placement on the right side of your gate when facing out from your property. It can be installed on the left side but some settings will need to be reversed for some functions like automatic closure to work properly.
20.1 in. (51 cm) Gate Opener Dimensions 13.4 in. (34 cm) 9.33 in. (23.7 cm) Figure 5 Mounting Plate Dimensions 12 in. (30.5 cm) 5.47 in. (13.9 cm) Ø0.59 in.
Base Installation Your motor MUST be firmly secured for safe user. Do not attempt to use it loose or only secured to thin pavement. 1. Use the two horizontal mounting plates (I) to brace the two vertical mounting plates (J) as shown. Use the M6×20 bolts (N), spring (W) and flat washers (T), and nuts (Q) to connect the plates so that both vertical plates face inwards on top and the large holes for the foundation bolts face out. 2.
Motor Installation M10 Nut 1. Remove the plastic casing from the motor (A). 2. Connect the motor to the base using the M10 bolts (P) with their spring (Y) and flat washers (V) and nuts (S). Adjust the placement of the bolts in their slots to match the expected path of the chain as shown. Normally, the path of the chain will be 1¼ to 1½ inches (32–39 mm) from the inner edge of the gate. M10 Spring Washer M10 Flat Washer M10×50 Bolt Mounting Base Figure 9 0.67–0.82 in. (17–21 mm) 1.25–1.54 in.
Chain Installation 1. Close the gate. 2. Install the gate brackets (H) at or near each end of your gate. They should face in towards your property and be located at the same height as the two smaller sprockets on the motor. The nearest bracket should be at least one foot (30 cm) away from the motor. Figure 13 Use the square bolts (G) for gates with square posts and the round bolts (G) for gates with round posts.
3. Fasten one of the chains (E) to the tie rod of the bracket farther from the motor by opening, positioning, and resealing its final chain link. Tie Rod If necessary, repeat the process to connect the two chains to one another or even to add additional lengths of chain. ONLY use ANSI #41 chain with this device and do not use any chain longer than 40 feet (12 m). Chain Link Chain Figure 16 4.
Magnetic Limit Installation Using this gate opener without its magnets in the correct position risks damage to the motor and to the gate, including possible derailment. 1. Place the motor in manual mode. Move the gate to the position you want it to go to when fully open. 2. Find the post on the open gate about 6–8 inches (15–20 cm) farther away from your driveway than the middle of the motor. 3. Find the position on that post exactly 3.98 inches (10.1 cm) above the middle of the taut chain. 4.
Capacitor Motor Ground Lamp Open Indicator Main Power Close Indicator 10A Fuse Voltage Transformer 24V DC Power Indicator Infrared Sensor Limit Switches External Button Connection Test Button Direction Switch Remote Signal Indicator Remote Pair Button DIP Switches IR Indicator Antenna Test Indicator Limit Indicators Figure 22 Optional Infrared Sensor Installation Receiver 1.
Initial Testing Left-Mounted 1. If the motor is located on the right side of your gate, the direction switch on its circuit board should be toggled to Forward (FWD). If it is located on the left side, toggle the switch to Reverse (REV). 2. Clear any obstacles from the gate’s path and keep all bystanders away. 3. Activate the power to your motor. The POWER and IR indicator lights should come on. 4. Test the infrared sensors by blocking the path between the two sensors with any obstacle.
Remote and Wireless Keypad Pairing 1. Up to 23 additional remote or wireless control buttons can be paired to the gate’s circuit board. Be sure that they use the 433.92 MHz radio band or can be configured to do so. NEVER pair the same button to 2 different gates or devices at the same time. Disconnect the motor from power, open its covers to expose its circuit board, Figure 26 and restore power. 2. Press the pairing button (AN). The remote indicator light (LEARN) should come on. 3.
Troubleshooting Potential Problems Possible Solution(s) The gate does not open or close normally and no indicator lights activate on the circuit board, even when pressing the TEST button. Verify that the power supply is functioning properly. Check that the fuse is not blown. Have a certified electrician rewire your system. Remove any obstacles which might be in the gate's path. The door opens but does not close.
Disposal Electrical products should not be disposed of with household products. In the EU and UK, according to the European Directive 2012/19/EU for the disposal of electrical and electronic equipment and its implementation in national laws, used electrical products must be collected separately and disposed of at the collection points provided for this purpose. Locations in Australia, Canada, and the United States may have similar regulations.
