Quick Start Guide
Instrucon Manual
Table of Content
Product and accessories ... ... ... ..1
Start to use.
..1
Hardware installaon
.. .. ..2
Mobile phone App installaon and use
.... ........ .3
Camera installaon....
.. .6
Wi-Fi network sengs ...
... 11
P2P mode .......
13
FAQ
........ 14
Product and accessories
1. Camera
2. Power adapter
3. Mounng bracket
4. Quick start guide
5. Disc
Start to use
Hardware installaon
Connect to camera AP
Add camera
Get real-me video, point-to-point
usa
g
e.Con
g
ure camera WIFI
Connect to router
Congure camera WIFI
Turn o camera AP, WIFI viewing
Mobile phone App installaon
1. Download and install HDWiCamPro from Apple Store for IOS, and search on
GooglePlay for Android. For easy installaon, please scan the below QR code to
download and install HDWiCamPro. If your device fails to connect to GooglePlay,
please scan the below APK QR code for download and installaon. Note: It is
recommended to use the QR code scanning soware that comes with your
browser or a thir
d party to scan and download App. Direct download and
installaon of App es is not supported by WeChat scan.
2. Click "+" to add a new camera. Click and add the connected camera, enter the
page for adding the camera, in the UID or password to add the camera. Note:
when using the camera for the rst me, please refer to "set up the camera to
connect to the WIFI network" secon on the instrucon to set up the camera to
connect to your router before adding the camera.
3. There are two ways to quickly enter the camera UID: A. Scan the QR code on
the camera;
B. Search the camera through the local network.
4. Fill in the camera name and the P2P password. The default P2P password is
6666. Conrm and click Ok. Camera is added successfully. It is recommended to
modify the P2P access password aer seng up the camera.
5. Aer the camera is showed online, then click the camera you just added to
watch the real-me video. You can control the device in the video interface.
6. Icons and buons for video pages
Camera plaorm
control
By PAN/TILT with your ngers on the video page, you can
control the rotaon of the camera plaorm, which depends
on the sliding distance of your nger (need to purchase
camera for support).
Users can hear the camera sound and have two-way voice
intercom (need to purchase camera for support).
Take snapshots and record video es
Flip images very and horizontally
Adjust brightness and contrast, tune intercom sound
Watch videos in the SD card
1. Other features of the page
Watch the current real-me video
View screenshots taken by the camera
View video es for your mobile device
View camera alarm event record
Camera seng
1. Click the gear bu at the back to open the advanced conguraon page of
the camera.
2. Modify the WIFI connecn. Select WIFI Sengs and the camera will show the
available Wi-Fi hotspots. Select your Wi-Fi network name (SSID), enter the Wi-Fi
password and press the nish key to connect. Note: Aer saving, if the camera is
connected to WIFI, the camera will disconnect the current connecon to try a
new WIFI network, which will cause the camera in the App to be temporarily
one for about 1 minute.
4. SD card video recording seng: Set the mode and the screen size of SD card
video recording.
Connect the camera to the Wi-Fi wireless network
For a new camera or the camera you install to a new locaon, please reset the
camera to default sengs (press and hold the camera reset buon for more
than 5 seconds aer the camera starts), and turn on AP mode aer the camera
restarts. The WIFI indicator light ashes slowly (once every 3 seconds). Then
turn on the phone sengs, connect the phone to the camera's AP hotspot (the
WIFI network is named aer the camera UID), and wait for the phone to switch
to the camera's WIFI network before starng App.
1. Connect the phone to the camera's AP hotspot (the WIFI network is named
aer the camera UID), and wait for the phone to switch to the camera's
WIFI network before starng App.
2. Select to add camera "+" in App
3. Select to connect the camera to the WIFI network
4. Click the WIFI conguraon, and then verify that the displayed WIFI network
name is the same as the UID number of the device. Then return to APP, the
device will be added automacally.
5. Then click the camera conguran page and click Wi-Fi Sengs, select the
router hotspot to be congured and enter the correct WIFI password, waing for
the camera to get online.
Note: if the App always fails, try to check the following:
A. Camera indicator light does not ash slowly and AP is not turned on before
you start conguring Wi
B. If the phone fails to connect to camera AP, you need to congure the phone
to connect to the AP hotspot of the camera.
C. Support ordinary routers.But public routers requiring login page
authencaon are not supported.
D. Make sure there are no errors in network name, net
work password and UID
when conguring.
E. Wi names and passwords in Chinese are not supported at this moment.
F. 5G Wi signal is not supported.
G. Check whether the Wi indicator light is always on, if yes, it means that the
camera networking is successful, please add an online camera directly, App may
not detect a successful camera conguraon due to network shielding.
H. If WiFi is WEP encrypon mode, change to WPA mode.
P2P mode viewing
You can view videos directly and operate on the camera without a Wi router.
Steps:
1. Reset the camera and wait for the camera to restart and turn on AP mode.
2. Aer the camera is started, you can nd the same Wi network as the camera
UID on the Wi seng page of the phone, without encrypon.
3. Connect your phone to the Wi network and wait for the icon of successful
Wi signal connecon.
4. Same as router mode, add an online camera directly and you
can turn it on for
normal use. If you have already added a camera, then you can connect directly.
5.Aer the connecon is successful, open and view the videos.
FAQ
1. Why the search tool is unable to detect the camera?
A: Please make sure if the network connecon is good, turn o the rewall
and security sware, and make sure the camera is connected to the router.
2. Why does the camera always require a user name and password, or an
incorrect user?
A: The default password for the camera is 6666. If you forget your user name
or password, you can resume the camera to the default sengs to get the
default
user name and password.
3. How can I resume my camera to default sengs?
A: Please press the reset buon on the camera for about 5 seconds un the
camera restarts.
4. Why the image is blurred?
A: Remove the protecve lm of the lens. If it is s not clear, rotate the
camera lens and focus it so that you can get a clear image aer focusing.