Wiring Instruction

ManualsBrandsDongGuan Tianluo Electronic Technology ManualsElectronics7 inch HD wireless video door phone

(3)Indoor display ON/Off operation

Drill 4 holes on wall to

fix mount bracket

Secure the bracket on

wall with screws

Fix camera on

the bracket

Turn on: For first time use, use USB charger to power supply the display, it will be

turned on automatically. ( Or in power suply status Press and hold the on/off button

for around 10 seconds till the screen is on.)

Turn off: Press and hold the on/off button for around 10 seconds till the screen shut off.

1.Press on display go to main menu , use arrow button to select“About”then press

to confirm.Select“Reset Setting”and confirm，then use arrow button and to input

the default password 1234 to reset the display to factory setting.

3.Use the arrow button and button to input the default password 1234 on indoor

display,it sounds“di di di ”and go to pairing mode, screen showing“pairing”

4.Then use pin to fast press the pair hole button three times on outdoor camera, the

green light bright, and it sounds“di di di ”go to pairing mode

5.Both indoor display and outdoor camera sound“duan”to prompt pair successfully,

display showing “pair success”

6.If pairing failed, will sound “dada”, display showing “pairing failed”, have to do

the above operations again.

Fix screw on the

left side to secure

the camera

4.Fast press the outdoor camera pair hole button

three times, it sounds "di di di"

Lock wiring diagram

Caution:

1.Please wire the lock with the Unlock module as per the diagram, then connect to electricity

power supply .

Connect the holes to the

terminal board and fix the screws

Press and hold one end of the

terminal block and connect the

wires to the ports

Press and hold the other end of

the terminal,regardless of positive

and negative, connect the cable of

the external power supply to the port.

1.Put the wiring board into the corresponding AC/DC hole on the back of

the video doorbell, and then fix the screws.

2.Use the matching push-type quick-connect terminal, keep one end pressed

down, insert the wires of the terminal block individually and release.

3.The other end also remains pressed down to connect to the external power

supply, regardless of positive and negative pole, just connect to the terminal

then release. Please note that the external power supply AC: 8-24V, DC: 8-36V.

2.Long press the pair button on unlock module for around 5 seconds till the red light tinkle

3.Indoor display in monitoring status, press the unlock button to open lock, the lock is

unlocked and the unlock module will sound“di”, prompt pairing successfully.

After pairing successfully, you can set the unlock time, default unlock time is 1 second.

Press one time the button on the unlock module, , red indicator light slowly twinkle three

times, set unlock time 3 seconds. Press one time again the button on the unloik module,

indicator light slowly twinkle five times, set unlocktime 5 seconds. Press the button one time

again, indicator light slowly twinkle eight times, set unlock time 8 seconds.

1.Press button to go the main menu.

1.Press button on display go to the main menu.

3.Use arrow button and button to input the

default password 1234

2. Click after selecting "Pair" menu .

Lock wiring diagram

Precautions

AC/DC wiring instruction

Main technical parameters

Trouble shooting

Main technical parameters

AC/DC wiring instruction

13 14 15

2.After reset the indoor display, go to main menu and select“Pair”and press enter

to“ Pair”menu

2 Select "monitor time" in the main menu, press

to confirm and go to“ monitor time“interface.

USB power cablewiring board

mounting screws

unlock box

(optional)

push-type quick-

connect terminal

display

Caution: The indoor display and outdoor camera is paired in factory,

no need to pair again. If the unit can not monitor or call or no signal ,

please contact your after sales service to confirm before following the

below operation.

1. Press go to main menu.

2.After going to volume setting interface, use

arrow button to adjust the volume and press

to confirm.

display

module

Screen brightness can be directly adjusted by pressing

up/down arrow button on the display.Press the no the

display to directly enter the event playback interface; on

the monitoring interface, press the up/down arrow button

to set the volume and brightness. There are language

Settings, IE cardcapacity, system upgrade andmore

functions waiting for you to experience.

display

Unlock module power supply

1. Press the go to main menu, select

“motion detection”, press go to

motion detection setting menu.

1. Press go to main menu.

Indoor display

Display size

Outdoor camera

Power

consumption

Battery capacity

Pixel

Electricity power supply

Camera angle

Night light

Standby 285uA Working 250mA

DC5V

5000mAh

1080P

DC8-36V, AC 8-24V

160°

850nm infrared lamp

Two way intercom

PIR motion detection

433Mhz wireless unlock

Working temperature

Size

Yes

-20°C ~ -60°

14.4*5.1*3.5cm

Power supply

7 inch

Power supply

Battery capacity

DC 5V

2000mAh

Working current

Two way intercom

Auto video record

video playback:Yes

800mA

Yes

Max support 64G

Screen resolution

Working temperature

Size

1280* 800

-20°C ~ -60°C

18.1*13.2*2.0cm

TF card

The unlock module already paired with the device in factory, no need to pair again. If prompt

not paired please confirm with your after sales service and refer the below operation.

call button

PIR

camera

pairing button

loudspeaker

USB charge port

AC/DC

Ⅹ.

Ⅺ.

Contents

Ⅺ

microphone

7 inch display

outd oor camera USB cable manual

Adapter

FCC Warning

This

device complies with part 15 of the FCC rules. Operation is subject to the following two

conditions: (1) this device may not cause harmful interference, and (2) this device must

accept any inte rference received, including interference that may cause undesired operation.

Changes or modifications not expressly approved by the party responsible for compliance

could void the user's authority to operate the equipment.

NOTE: This equipment has been tested and found to comply with the limits for a Class B

digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide

reasonable protection against harmful interference in a residential installation. This

equipment generates uses and can radiate radio frequency energy and, if not installed and

used in accordance with the instructions, may cause harmful interference to radio

communications. However, there is no guarantee that interference will not occur in a

particular installation. If this equipment does cause harmful interferenceto radio or television

reception, which can be determined by turning the equipment off and on, the user is

encouraged to try to correct the interference by one or more of the following measures:

-Reorient or relocate the receiving antenna.

•Increase the separation between the equipment and receiver.

•Connect the equipment into an outlet on a circuit different from that to which the receiver is

connected.

•Consult the dealer or an experienced radio/TV technician for help.

Radiation Exposure Statement

This equipment complies with FCC radiation exposure limits set forth for an uncontrolled

environment. This equipment should be installed and operated with minimum distance 20cm

between the radiator and your body.