ADD:3rd floor,building 1,SME park,songshan Dongguan Saftire Auto Safety Technology,Co.
ADD:3rd floor,building 1,SME park,songshan Dongguan Saftire Auto Safety Technology,Co.,Ltd l k d i d i hi Notice Please read the safety cautions below carefully before installing this product: Please make sure that this product can be used in your car and you can install it correctly before installation, so that no negative impact could be caused. 1. The monitor shall be mounted in a place where the driver’s sight is not blocked or influenced negatively. 2.
ADD:3rd floor,building 1,SME park,songshan Dongguan Saftire Auto Safety Technology,Co.,Ltd l k d i d i hi vehicle’s comfortability and prevent tire’s flat, reduce oil comsumption, decrease tires’ abrading and increase the dynamic performance indirectly. 2. Installation illustration 2.1 Monitor installation 2.1.1 Receiver base installation diagram 1 Holder is access from ○ 2 Push the holder up to ○ the slot under the back of receiver make it fit the receiver and lock completely 2.1.
ADD:3rd floor,building 1,SME park,songshan Dongguan Saftire Auto Safety Technology,Co.,Ltd l k d i d i hi Serial port line(Option): Notice: Monitor should be installed at the suitable position that won’t affect driving sight Should make sure the monitor be reinforced to avoid falling when driving When check the pressure and temperature during the driving, pls.
ADD:3rd floor,building 1,SME park,songshan Dongguan Saftire Auto Safety Technology,Co.,Ltd l k d 1 The steel tie around the hub ○ ②Put the sensor on the steel tie ④Installing non-slip rubber pad ⑤Tighten the steel tie screw i d i hi ③Pre tighten steel tie screw ⑥Installation completed Notice: The installation position of the sensor should be close to the valve position, which is convenient for the receiver to match with the sensor after installing tire.
ADD:3rd floor,building 1,SME park,songshan Dongguan Saftire Auto Safety Technology,Co.,Ltd l k d i d i hi in the box with a monitor installed in the car; 3.The sensor and tighten the valve stem to the original car, it will go through a process of deflated, because between the sensor produces gas nozzle would contradict the original car and the valve core valve caused the leak, then please continue to tighten as soon as possible sensor until no leak, and the sensor can not be screwing up; 4.
ADD:3rd floor,building 1,SME park,songshan Dongguan Saftire Auto Safety Technology,Co.,Ltd l k d i d i hi ① Remove the tires from truck and deflated to tire ② Remove the tires from wheel; ③ Fix the sensor to wheel according the picture④&⑤; ④ Fix the sensor via screw like picture⑥; ⑤ Install tires, and give the tire to the standard air pressure like picture⑦); ⑥ Check the tire, we can re-fix the sensor if the tire is leakage; 2.5 Intelligent repeater installation 2.5.
ADD:3rd floor,building 1,SME park,songshan Dongguan Saftire Auto Safety Technology,Co.,Ltd l k d i d i hi 2.5.2 Installation method As diagram Effect picture after installation(perpendicular to car chassis cross beam) Notice: There are 2 power line of intelligent repeater. Red power line connects positive pole of truck normal open power, black power line is ground connection. Pls. fasten the power lines by ribbon to prevent from wearing and short circuit.
ADD:3rd floor,building 1,SME park,songshan Dongguan Saftire Auto Safety Technology,Co.,Ltd l k d i d i hi Please access a 2A waterproof type fuse in the position of intelligent repeater connecting car normal open power, in order to ensure the safety of the circuit. 3.System Function 3.1 Turn on/off monitor You can move the “ON/OFF” switch when you need to long time parking. There will be a sound hint of no electricity and battery electric quantity display symbol flashing.
ADD:3rd floor,building 1,SME park,songshan Dongguan Saftire Auto Safety Technology,Co.,Ltd l k d i d i hi 3.
ADD:3rd floor,building 1,SME park,songshan Dongguan Saftire Auto Safety Technology,Co.,Ltd l k d i d i hi 4.System display 4.1 Tire mode Imitation truck modeling, left side is truck head, right side is truck body. Every tire using small rectangle to express, maximum can setup 46 tires(front 2 tires, back 44 tires) 4.
ADD:3rd floor,building 1,SME park,songshan Dongguan Saftire Auto Safety Technology,Co.,Ltd l k d i d i hi P7:Sensor position exchange 5.3 Factory default setting data Item Setting data Pressure unit Psi High pressure warning data Low pressure warning data Temperature unit High temperature warning data 174Psi 87Psi ℃ 90 ℃ 6. Intelligent trailer’s application 6.1 Illustration In fleet, one head often needs to link many trailer.
ADD:3rd floor,building 1,SME park,songshan Dongguan Saftire Auto Safety Technology,Co.,Ltd l k d 1 Screen ○ 2 Entering ○ display“P6”, shortly press i d i hi key for 1 second. trailer pairing setting, the screen display original ID, botton right corner data is repeater’s serial number. 3 Shortly ○ press key for 1 second,the screen displays“- - -”,“REPEATER ON”blinks,it shows it’s waitng for receiving the repeater’s ID.
ADD:3rd floor,building 1,SME park,songshan Dongguan Saftire Auto Safety Technology,Co.,Ltd l k d i d i hi 4 Power the repeater on, receiver receives new repeater’s ID, the screen ○ displays ID data and sounds “tick”, the data blinks 3 times. 5 Skip ○ to next repeater automatically. If need to pair many repeaters, can repeat the opeartion process as ③-④, max. 10 repeaters. 6 Long ○ press key for 3 seconds to keep ID and exit to system setting mode.
ADD:3rd floor,building 1,SME park,songshan Dongguan Saftire Auto Safety Technology,Co.,Ltd l k d i d i hi Intelligent repeater and receiver power on simultaneously, intelligent repeater sends ID data signal, the receiver receives and screen will display require link order as “REPEATER ON”blinks(as below diagram①). Press key on the receiver, assemble the intelligent repeater(as below diagram②).If press key,means won’t assemble intelligent repeater(as below diagram③).
ADD:3rd floor,building 1,SME park,songshan Dongguan Saftire Auto Safety Technology,Co.,Ltd l k d i d i hi (3)Sensor pairing, ID learning 1 screen ○ 2 Entering ○ display as “P2”, shortly press sensors’ pairing setting function(first tire blinks, screen display the paired ID data),press and press 3 Screen ○ key 1 second. or key,locate the pairing tire position after confirmation. skip as “- - -” “LEARNING” start to blink, shows it is waiting for receiving sensor’s ID.
ADD:3rd floor,building 1,SME park,songshan Dongguan Saftire Auto Safety Technology,Co.,Ltd l k d 4 Handheld ○ i d i hi tool(or tire inflation/deflation,remove sensor or tighten sensor when you use external sensor) activates the sensors. 5 Receive ○ new sensor’s ID, the screen display full ID data and sounds “tick”. ID data blinks 3 times and skip to next tire automatically. 6 If ○ press cancel pairing operation, when the screen display as “--- --- --”,shortly for 1 second.
ADD:3rd floor,building 1,SME park,songshan Dongguan Saftire Auto Safety Technology,Co.,Ltd l k d 7 After ○ finishing the setting, long press i d i hi key for 3 seconds to save and exit back to system setting mode. 8 Long ○ press key for 3 seconds and exit to normal working status. 6.3 Other mode setting method z Notice: Explain in detail the setting method of P1、P3、P4、P5 and P7 in order as following. Take setting 22 tires for example: 6.3.
ADD:3rd floor,building 1,SME park,songshan Dongguan Saftire Auto Safety Technology,Co.,Ltd l k d 1 Display“P1”, ○ press i d i hi 1s 。 ② Enter sign tire setting function(left side data shows the selecting tire position, right side data shows the signed tires quantity),press or key,locate the tire position. ③ When left side data is “11”,shortly press key for 1 second. ④ Finish sign and skip to next tire blink automatically.
ADD:3rd floor,building 1,SME park,songshan Dongguan Saftire Auto Safety Technology,Co.,Ltd l k d ⑤ Always shortly press i d i hi key for 1 second,until sign 22pcs of tire, shows the sign finished. ⑥ If sign more tire, shortly press (as diagram above),shortly press for 1 second to cancel. ⑦ After finishing the sign, long press key for 3 seconds to save and exit back to system setting mode. ⑧ Long press key for 3 seconds to exit back to normal working status.
ADD:3rd floor,building 1,SME park,songshan Dongguan Saftire Auto Safety Technology,Co.,Ltd l k d 7 i d i hi P3 Unit setting ① Screen displays“P3”,shortly press key for 1 second. ② Entering unit setting function(left side display air pressure unit, right side displays temperature unit).
ADD:3rd floor,building 1,SME park,songshan Dongguan Saftire Auto Safety Technology,Co.,Ltd l k d ④ Press i d i hi key to select temperature unit. ⑤ After finishing the setting, long press key for 3 seconds to save and exit back to system setting mode. ⑥ Long press key for 3 seconds to exit to normal working status.
ADD:3rd floor,building 1,SME park,songshan Dongguan Saftire Auto Safety Technology,Co.,Ltd l k d 8 i d i hi P4 Tire pressure warning threshold value setting 1 Screen ○ displays “P4”, shortly press key for 1 second. ②Enter tire pressure warning threshold value setting function(screen display high pressure warning threshold value,“HIGH PRESSURE”blink). ③Shortly press key for 1 second,high pressure warning data starts to blink on the screen.
ADD:3rd floor,building 1,SME park,songshan Dongguan Saftire Auto Safety Technology,Co.,Ltd l k d ④Press or d i hi key to adjust the data, the range is 7Bar-14Bar. After confirmation, press ⑤Press i key for 1 second to save the data. setting Low pressure alarm limit value, “LOW PRESSURE” flashing 6 Shortly ○ press key for 1 second, the low pressure warning data starts to blink on the screen.
ADD:3rd floor,building 1,SME park,songshan Dongguan Saftire Auto Safety Technology,Co.,Ltd l k d ⑦ Press or i d i hi key to adjust data, the range is 5Bar-6.9Bar. After confirmation, shortly press key for 1 second to save data. ⑧ After finishing the setting, long press key for 3 seconds to save and exit back to the system setting mode. ⑨ Long press key for 3 seconds exit to normal working status.
ADD:3rd floor,building 1,SME park,songshan Dongguan Saftire Auto Safety Technology,Co.,Ltd l k d 9 i d i hi P5 Tire temperature warning threshold value setting 1 Screen ○ 2 Enter ○ displays “P5”, shortly press key for 1 second. high temperature warning data setting function, temperature data blinks. 3 Press ○ or key,adjust high temperature warning data, the range is 50℃-120℃.
ADD:3rd floor,building 1,SME park,songshan Dongguan Saftire Auto Safety Technology,Co.,Ltd l k d 4 After ○ finishing the setting, long press i d i hi key for 3 seconds to save and exit back to system setting mode. 5 Long ○ press key for 3 seconds to exit to normal working status. 10 P7 Sensor position exchange 1 Screen ○ display “P7”, shortly press key for 1 second.
ADD:3rd floor,building 1,SME park,songshan Dongguan Saftire Auto Safety Technology,Co.,Ltd l k d 2 Enter ○ i d i hi the sensors exchange function, the screen displays the positions of two tires which needs exchange, left side data blinks. 3 Press ○ 4 After ○ or key,select the first tire which needs to exchange. confirmation, shortly press key for 1 second, skip to right data automatically, data blinks.
ADD:3rd floor,building 1,SME park,songshan Dongguan Saftire Auto Safety Technology,Co.,Ltd l k d 5 Press ○ 6 Long ○ or i d i hi key to select second tire which needs to exchange press key for 3 seconds to exchange, save and exit back to system setting mode. 7 Long ○ press key for 3 seconds to exit to normal working status.
ADD:3rd floor,building 1,SME park,songshan Dongguan Saftire Auto Safety Technology,Co.
ADD:3rd floor,building 1,SME park,songshan Dongguan Saftire Auto Safety Technology,Co.,Ltd l k d i d i hi Sensor low voltage warning Correspondent tire icon blinks, meanwhile, shows LOW VOLTAGE and sensor low 4 voltage warning icon; (Battery voltage warning value is 2.3V) Icon shows the third sensor low voltage warning.
ADD:3rd floor,building 1,SME park,songshan Dongguan Saftire Auto Safety Technology,Co.,Ltd l k d i d i hi 12 Product technical parameter 12.1 Monitor No. Item Technical parameter 1 Input voltage DC24 V 2 Battery voltage 3 Charging time 4 HF emit working frequency 5 RF power 6 HF receive frequency 7 HF receive sensitivity 3.0~4.2 V 5 H 433.92 MHz ﹤5 dB 433.92 MHz >-90dbm 12.2 . External sensor The only External sensor’s that is approved to work with this TPMS is FCC ID: ZPNVS62U009.
ADD:3rd floor,building 1,SME park,songshan Dongguan Saftire Auto Safety Technology,Co.,Ltd l k d i d i hi 13 Simple trouble removal If encountering a problem during assembling or usage, pls. try to use below methods to solve. If the problem is still there, pls. contact our after-sale service center. Problem phenomenon Reason analysis When The tire pressure after installation the same is as not real measurement first Solution time assembling, power on to start receiver.
ADD:3rd floor,building 1,SME park,songshan Dongguan Saftire Auto Safety Technology,Co.,Ltd l k d i d i hi FCC Statement Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules.