Operating Instructions

8HR
6HR
4HR
2HR
ON
DUSK-
DAWN
OFF
POWER
5. Installation work and electrical wiring must be done by qualified person(s) in acc-
6. do not install or use within 10 feet of a pool
7. do not use in a bathroom
8. WARNING:
9. WARNING:
10.WARNING:
SAVE THESE INSTRUCTIONS
– This manual contains important safety and operating
instructions.
Risk of Electric Shock.
Mount the unit at a height greater than 1 foot from the ground surface
Risk of Electric fire. install only to a receptacle protected by 20A branch
circuit over current protection.
Risk of Electric Shock.
When used outdoors, install only to a covered Class A GFCI protected receptacle
that is weatherproof with the power unit connected to the receptacle. If one is not
provided, contact a qualified electrician for proper installation. Ensure that the pow-
er unit andcord do not interfere with completely closing the receptacle cover.
ordance with allapplicable codes and standards, including fire-rated construction.
• OFF – power OFF
• ON – power ON
• 2Hrs, 4Hrs, 6Hrs or 8Hrs – ON at dusk, OFF 2, 4, 6 or 8 hours later
• DUSK-DAWN – ON at dusk, OFF at dawn
SIZE: 245 x 127 mm
材质：80G 书写纸
单色黑白印刷
拆法：对折页 123 x 64mm 成品
MP42T(TS961R)
Thank you for visiting !
If you have any questions, please contact us at
This device complies with Part 15 of the FCC Rules. Operation is subject to the
following two conditions:
(1) This device may not cause harmful interference,
may cause undesired operation. changes or modifications not expressly approved
by the party responsible for compliance could void the user's authority to operate
the equipment.
(2) This device must accept any interference received, including interference that
FCC warning:
This equipment has been tested and found to comply with the limits for a Class B
digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to
provide reasonable protection against harmful interference in a residential installa-
tion. This equipment generates, uses and can radiate radio frequency energy and,
if not installed and used in accordance with the instructions, may cause harmful int-
erference to radio communications. However, there is no guarantee that interferen-
ce will not occur in a particular installation. If this equipment does cause harmful in-
terference to radio or television reception, which can be determined by turning the
NOTE:
1. READ AND FOLLOW ALL SAFETY INSTRUCTIONS.
2. Read and follow all instructions that are on the product or provided with the
3. do not use an extension cord.
4. Reference the National Electrical Code, NFPA 70, specifically for the installation
of wiring andclearances from power and lighting conductors.
product.
equipment off and on, the user is encouraged to try to correct the interference by
one or more of the following measures:
-- Reorient or relocate the receiving antenna.
-- Increase the separation between the equipment and receiver.
-- Connect the equipment into an outlet on a circuit different from that to which the
receiver is connected.
-- Consult the dealer or an experienced radio/TV technician for help.
CAUTION - PLEASE READ!
This device is intended for installation in accordance with the National Electric Code
and local regulations in the United States, or the Canadian Electrical Code and
local regulations in Canada. If you are unsure or uncomfortable about performing
this installation consult a qualified electrician.
MEDICAL EQUIPMENT
Please DO NOT use this plug to control Medical or Life Support equipment.
This device should never be used to control the On/Off status of Medical and/or Life
Support equipment.
OTHER WARNINGS
Risk of Fire / Risk of Electrical Shock / Risk of Burns
IMPORTANT SAFETY INSTRUCTIONS
www.minoston.com
[e-mail]
Scan QR code or visit
Model – MP42T(TS961R)
Model:MP42T-TX97(remote control)
Specifications
Ratings (Total both outlets)
125V, 60Hz, Max.15A GP
15A Resistive
1000W Incandescent
1000W Tungsten
1/3 HP
TYPE 3R Enclosure
Wireless Frequency: 433MHz Rainproof
Remote Battery: CR2032 * 1
Manual/program button
CR2032 Battery x 1
Remote Control x 1
Outdoor Plug-in Photocell Timer with Remote
Notes: The outlet is pre-programmed for immediate use,
but the configuration can be customized to meet your needs.
To pair receiver to transmitter
1. Plug the receiver outlet to a power outlet.
2. Press and hold the ON/OFF button on the receiver outlet for
3. Release the ON/OFF button on the receiver and press ON or
OFF button on the transmitter to pair the transmitter to the receiver.
3 seconds and the LED indicator will start flashing slowly.